LM224ADRE4 - Quad 32V 1.2MHz Op Amp | Texas Instruments
料号: LM224ADRE4 ✓ 量产中LM224ADRE4 概述
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The LM224 family belongs to the broader hierarchy of amplifier ICs, analog signal-conditioning ICs, and semiconductors. Internally frequency-compensated amplifiers simplify closed-loop design by removing the need for an external dominant-pole capacitor in many conventional gain configurations.
The LM224ADRE4 provides four high-gain amplifiers in one package, allowing a design to use several independent analog channels without allocating separate single or dual amplifier packages. Typical input offset voltage is 2 mV, typical input bias current is 2 nA, and typical supply-current drain is 0.8 mA. Its common-mode input range includes ground, which supports direct sensing of signals near the negative supply rail.
The 1.2 MHz gain-bandwidth product defines the frequency range available for closed-loop amplification and is particularly useful for low- to moderate-frequency signal paths. A 0.5 V/µs slew rate supports accurate output transitions in amplifier networks that process bipolar, sensor, or control signals. Four amplifiers in one 14-pin SOIC can also reduce board area and simplify assembly compared with four separate single-amplifier packages.
Typical uses include temperature and pressure sensor interfaces, low-level signal conditioning, industrial control loops, instrumentation, and general voltage amplification. In sensor applications, the amplifier can convert a small transducer voltage into a larger signal suitable for an ADC or controller. In control systems, the four channels can support conditioning, active filtering, error amplification, and output buffering within one circuit board.
For reliable operation, maintain adequate supply headroom and verify that input and output voltage excursions remain within the common-mode and output limits stated in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance so that oscillation, offset, or saturation does not affect the assembled circuit.
直接替换替代料: LM224ADRE4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM224ADRE4 (相同外形与封装尺寸) ——差异在于 Amplifier Type, Operating Temperature Range, Package.
LM324BAIDR
✅ 直接替换联系询价
查看数据手册 →LM2902B
✅ 直接替换📋 参考替代料(不在目录中)
LM224ADRE4 最大额定值与电气特性
| Number of Amplifiers | 4 channels |
| Amplifier Type | High gain, internally frequency compensated |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Minimum Supply Voltage | 3 V |
| Maximum Supply Voltage | 32 V |
| Typical Input Offset Voltage | 2 mV |
| Typical Input Bias Current | 2 nA |
| Typical Supply-Current Drain | 0.8 mA |
| Common-Mode Input Range | Includes ground |
| 工作温度范围 | -25 °C to +85 °C |
| 引脚数 | 14 pins |
| 封装 | 14-pin SOIC |
| 安装类型 | Surface mount |
| RoHS 状态 | Compliant |
| Supply Voltage Configuration | Single or split supply |
LM224ADRE4 14-pin soic 引脚配置指南
LM224ADRE4(14-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM224ADRE4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM224ADRE4 适用于 6 应用s: Temperature Sensor Signal Conditioning, Industrial Process Control, Pressure Sensor Interface, Instrumentation and Measurement, Data Acquisition Conditioning, Power Supply Feedback and Control Loops.
Temperature Sensor Signal Conditioning
The LM224ADRE4 fits low-level temperature-sensor front ends because its 1.2 MHz gain-bandwidth product handles slow sensor signals while its 2 mV typical input offset voltage limits the input-referred error. The common-mode input range includes ground, allowing the amplifier to operate with the signal near the lower rail on a single supply. Use one channel to amplify the sensor output and configure the remaining channels for filtering, reference buffering, or diagnostics. Because a 14-pin SOIC contains four amplifiers, the design can consolidate several analog functions without adding separate amplifier packages.
推荐
Industrial Process Control
The LM224ADRE4 is appropriate for low-frequency industrial process-control loops that require amplification of sensor and error signals. Its 3 V to 32 V supply range supports more operating headroom than many low-voltage precision amplifiers, while 0.8 mA typical supply-current drain helps limit power consumption. The four internal channels can provide sensor conditioning, active filtering, comparator-like error amplification, and actuator-signal buffering. Designers should use the manufacturer pinout, keep feedback loops compact, and confirm output swing at the selected supply voltage and load.
推荐
Pressure Sensor Interface
The LM224ADRE4 can condition the millivolt-level output of a resistive or bridge-based pressure sensor. The 2 mV typical input offset voltage is important when the amplified result is intended to preserve small sensor changes, and the 2 nA typical input bias current supports high-impedance sensing networks. Its 1.2 MHz gain-bandwidth product is more than adequate for pressure signals that change slowly compared with audio bandwidth. A practical implementation may dedicate separate channels to sensor amplification, offset correction, filtering, and output buffering.
推荐
Instrumentation and Measurement
The LM224ADRE4 fits general-purpose instrumentation where several low-frequency analog signals must be measured or buffered. Four high-gain amplifiers in one 14-pin SOIC reduce the number of separate analog packages and allow the board to combine input conditioning, gain stages, and active filters. The 0.5 V/µs slew rate supports reasonably clean signal transitions, while the 1.2 MHz gain-bandwidth product covers many audio-band measurement functions. For precision instruments, engineers should evaluate offset and bias errors against the required accuracy and use the manufacturer’s recommended layout for decoupling and feedback routing.
推荐
Data Acquisition Conditioning
The LM224ADRE4 can serve as the analog conditioning stage between low-level transducers and an ADC or data-acquisition controller. Its four amplifier channels allow several inputs to be amplified and filtered with a common device architecture, while the 3 V minimum supply supports operation from compact 5 V systems. The 1.2 MHz gain-bandwidth product permits useful bandwidth for many sensor channels, and the common-mode range including ground supports measurements near the supply floor. Input protection, settling time, and simultaneous-channel performance should be checked against the acquisition system’s sampling requirements.
推荐
Power Supply Feedback and Control Loops
The LM224ADRE4 is suitable for power-supply feedback and supervisory control circuitry operating from elevated rails. Its 32 V listed maximum supply supports applications that operate above common 5 V or 12 V analog ranges, and the four channels can implement voltage-error amplification, current-sense amplification, filtering, and buffered control signals. The 0.8 mA typical supply-current drain is useful in space-constrained or power-conscious designs. Compensation components and loop stability must be derived for the actual converter topology rather than copied without review.
推荐
推荐产品汇总
工程参考数据: LM224ADRE4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM324B | LM2902B |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Number of Amplifiers | 4 channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 32 V | 36 V | 36 V |
关键差异点
- Four independent amplifiers consolidated into one 14-pin SOIC (对比 LM324B)
- Targeted alternative with a lower supply ceiling (对比 LM2902B)
- Single-package integration for multichannel analog conditioning (对比 LM324B)
设计说明
Place the manufacturer-recommended supply-bypass capacitor directly between the supply and ground pins of the SOIC. Keep the capacitor and device ground connection short to reduce parasitic inductance, which can improve transient response and help prevent oscillation. Route sensitive input and feedback traces away from the supply-capacitor return current. The 14-pin SOIC footprint should also leave adequate clearance for the lead-forming and soldering process used by the assembly house.
Do not assume that the input common-mode range extends across the entire supply rail merely because the range includes ground. The manufacturer datasheet contains the exact input common-mode and output-swing limits, and the output must also remain within its linear operating region. Gain and feedback values should be checked for stability, especially at higher closed-loop gains where the 1.2 MHz gain-bandwidth product limits usable bandwidth.
Keep each amplifier’s input, feedback, and output loop physically compact to minimize parasitic capacitance and susceptibility to EMI. Grounding should follow the datasheet’s recommended single-point or quiet-ground strategy rather than separating analog and power returns excessively. For four-channel designs, avoid routing high-current or switching-node copper beneath the SOIC, and place input-referenced components close to their associated amplifier pins to minimize board-level noise pickup.
Check every rail and signal excursion against the 3 V to 32 V operating range, including transients caused by inductive loads or switching-supply overshoot. The LM224ADRE4’s typical supply-current drain is 0.8 mA, but total channel and load currents still contribute to device power dissipation. Use conservative supply design margins and verify temperature rise in the assembled PCB rather than inferring thermal performance from the low quiescent current alone.
合规信息
RoHS compliance is identified by the LM224ADRE4 technical listing. Other environmental and material-compliance declarations are not specified on that listing.