Texas Instruments

LM258ADGKR - Dual 30V 700kHz Op Amp | Texas Instruments

MPN: LM258ADGKR ✓ چالاک
30 V Vdss 40 nA Id 8-pin VSSOP (DGK) Package
MOQ: 1 |

LM258ADGKR گشتی

The Texas Instruments LM258ADGKR is a dual, general-purpose operational amplifier rated for a maximum total supply voltage of 30 V, a typical gain-bandwidth product of 700 kHz, and a maximum input offset voltage of 3 mV. The device is packaged in an 8-pin VSSOP (DGK) and operates from -25°C to 85°C.

An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM258 belongs to the general-purpose amplifier family within the broader voltage-feedback amplifier hierarchy. Its frequency compensation is internal, allowing each channel to operate as a stable closed-loop amplifier without an external compensation capacitor.

The two channels feature a typical slew rate of 0.3 V/µs, low supply-current drain of approximately 0.7 mA, and low input bias current. Each amplifier can operate from a single supply or from split supplies. The common-mode input range includes ground, which supports direct sensing of signals near the negative rail and makes the device useful in battery-powered monitoring circuits.

Common applications include low-frequency sensor conditioning, transducer amplification, audio preamplification, analog signal filtering, and general control loops. Because the LM258ADGKR provides more supply-voltage headroom than many modern rail-to-rail amplifiers, it remains useful when signals exceed 12 V or when a single supply of 24 V must be accommodated. The output stage does not rail-to-rail swing, so output-headroom calculations are required at the chosen supply voltage.

When designing a new board, use a 100 nF bypass capacitor close to each supply pin and verify output swing, load current, stability, and common-mode range at the actual signal amplitude. Confirm that the amplifier output remains above the lower saturation limit and below the upper load-dependent limit.

This page combines manufacturer specifications, package details, drop-in replacement options, application guidance, and practical design notes to support component selection and PCB implementation.

جێگرەوەکانی جێگۆڕکێ بۆ LM258ADGKR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM258ADGKR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Maximum Supply Voltage, Number of Channels, Operating Temperature Range, Package.

Texas Instruments
Maximum Supply Voltage: 26 V
Number of Channels: 2 channels
Package: 8-pin VSSOP
بەراوردکردن لەگەڵ LM258ADGKR →
Texas Instruments
Amplifier Type: Dual general-purpose operational amplifier
Maximum Supply Voltage: 30 V
Operating Temperature Range: 0 °C to +70 °C
بەراوردکردن لەگەڵ LM258ADGKR →

LM358ADGKR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin VSSOP (DGK)
Dual general-purpose operational amplifier · 2 channels · 30 V · 700 kHz · 3 mV · 0 °C to +70 °C · VSSOP (DGK) · 8 pins

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DGKR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin VSSOP (DGK)
General-purpose operational amplifier · 2 channels · 26 V · 700 kHz · Push-pull · Extends to ground

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM258ADGKR زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type General-purpose operational amplifier
Number of Channels 2
Number of Amplifiers 2
Maximum Total Supply Voltage 30 V
Supply Voltage Range 3 V to 32 V
Typical Gain-Bandwidth Product 700 kHz
Typical Slew Rate 0.3 V/µs
Maximum Input Offset Voltage 3 mV
Typical Input Bias Current 40 nA
Typical Supply Current 0.7 mA
ئێستای دابینکردن 800 µA
Typical Output Current per Channel 30 mA
مەودای پلەی گەرمیی کارکردن -25°C to 85°C
Input Common-Mode Range Includes ground
Compensation Internal
Supply Configuration Single or split supply
پاکێج 8-pin VSSOP (DGK)
جۆری دامەزراندن Surface mount

ڕێکخستنی پینی LM258ADGKR

MSOP-8 Package Pinout Diagram MSOP-8 3x3mm, P0.65mm, JEDEC MO-187. 1 8 2 7 3 6 4 5 MSOP-8
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 V- — Negative supply connection
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 V+ — Positive supply connection

بەکارهێنانە باوەکان

LM258ADGKR گونجاوە بۆ 6 بەکارھێنانs: 24 V Industrial Sensor Conditioning, Audio Preamplifier Stage, Power-Supply Feedback Control, Transducer Bridge Amplifier, Battery and Portable Monitor, Analog Control and Filter Stage.

🏭

24 V Industrial Sensor Conditioning

The LM258ADGKR fits 24 V industrial sensor-conditioning circuits because it operates across a 3 V to 32 V supply range and its common-mode input includes ground. Place it between a resistive divider or transmitter interface and an analog-to-digital converter. The 700 kHz gain-bandwidth product provides margin for moderate-gain stages, while 0.3 V/µs slew rate suits low-frequency process signals. Protection networks, an input common-mode check, and output-headroom analysis remain essential because the amplifier is not rail-to-rail.

🎧

Audio Preamplifier Stage

The LM258ADGKR can serve as a general-purpose audio preamplifier for low-frequency and microphone-level signals when a rail-to-rail output is unnecessary. Its dual configuration allows one channel to amplify the audio input while the other handles a monitoring or bias function. The 3 mV maximum input offset voltage is modest for precision audio paths, so gain-network resistor matching should be checked for channel-to-channel offset. Output swing must remain within the supply limit at the selected load.

⚡

Power-Supply Feedback Control

The LM258ADGKR is appropriate for slow feedback loops in regulated power supplies because it accepts a wide supply range and provides two amplifiers for error amplification and auxiliary functions. Its 700 kHz bandwidth is sufficient for many control loops that do not require a modern high-speed error amplifier. Compensation must be recalculated when the feedback network changes, and the output must be kept above the saturation region. The device also tolerates higher supply voltages than typical 3.3 V and 5 V amplifiers.

📱

Transducer Bridge Amplifier

The LM258ADGKR can amplify the low-level differential output of resistive bridges and passive transducers when the signal bandwidth is well below 700 kHz. Its two channels may support differential excitation control and differential sensing, although offset and bias-current matching should be reviewed in the final schematic. The common-mode input range including ground helps with near-ground bridge outputs. Add input clamps and EMI filtering on long sensor cables to prevent overload and transient damage.

🔋

Battery and Portable Monitor

The LM258ADGKR is useful in battery-operated monitors because it operates from a single supply down to 3 V and its common-mode input range extends to ground. It can monitor a divided supply or sensor signal while operating directly from a low-voltage cell. The low typical supply-current drain of 0.7 mA supports battery conservation, although the complete circuit budget must include divider, reference, and protection leakage. Verify output headroom because the output does not swing fully to either rail.

🔧

Analog Control and Filter Stage

The LM258ADGKR supports active filters, integrators, and slow proportional-control loops where the signal bandwidth remains below the device's 700 kHz gain-bandwidth product. Internal frequency compensation enables straightforward inverting and non-inverting configurations. Component tolerances in the feedback network directly affect gain and cutoff accuracy, so 1% resistors are usually preferable for repeatable production behavior. Validate stability with the actual load and output-bias conditions rather than relying only on nominal gain calculations.

What are the key specifications of LM258ADGKR that engineers should know?
The LM258ADGKR is a dual, general-purpose operational amplifier with a 30 V maximum total supply voltage, 700 kHz typical gain-bandwidth product, 0.3 V/µs typical slew rate, and 3 mV maximum input offset voltage. According to the Texas Instruments LM258A datasheet, both channels operate from a 3 V to 32 V supply and are temperature-rated for -25°C to 85°C. The unit is offered in an 8-pin VSSOP package.
Where can I download the LM258ADGKR datasheet PDF?
The LM258ADGKR datasheet is available from the Texas Instruments LM258A product page and the LM258 family landing page. The manufacturer data describes the part as a dual, 30 V, 700 kHz operational amplifier with a 3 mV maximum offset voltage. Use the LM258A datasheet for the DGK orderable details, pin configuration, electrical characteristics, and application information.
What is the LM258ADGKR pinout and package?
The LM258ADGKR uses an 8-pin VSSOP with the standard dual-op-amp arrangement. Pins 1 and 7 are the two outputs, pins 2 and 6 are the inverting inputs, pins 3 and 5 are the non-inverting inputs, pin 4 is V-, and pin 8 is V+. According to Texas Instruments ordering information, the package designation is DGK with 8 pins.
Can LM258ADGKR operate from a single 5 V supply?
Yes, the LM258ADGKR can operate from a single 5 V supply because its supported supply-voltage range extends down to 3 V. The Texas Instruments LM258A datasheet specifies operation from 3 V to 32 V with single or split supplies. At a 5 V supply, however, the output swing remains limited, so the required output amplitude must remain inside the load-dependent output-voltage range.
What can replace an LM258ADGKR on an existing PCB?
The LM358ADGKR is the closest documented drop-in option because it retains the dual general-purpose amplifier architecture, 700 kHz-class bandwidth, and compatible VSSOP footprint. The LM2904DGKR provides a wider-temperature alternative with similar dual-amplifier functionality. Texas Instruments identifies LM358B as a drop-in replacement with upgraded functionality for the LM258 family. Confirm pin, package, supply-voltage, and temperature requirements against the selected replacement datasheet.
Is the LM258ADGKR the same as an LM358?
The LM358 family is related to the LM258 family but is not guaranteed to be identical in every electrical characteristic. The LM258ADGKR has a 30 V maximum total supply specification and a 3 mV maximum input offset voltage, while the LM358 replacement family may specify different offset and temperature grades. Texas Instruments describes LM358B as a drop-in replacement with upgraded functionality, so board use should be confirmed against the specific replacement orderable MPN.
When should I choose LM258ADGKR instead of LM358ADGKR?
Choose LM258ADGKR when the design specifically specifies the LM258A offset grade, the 30 V maximum total supply rating, or an approved LM258A-based BOM. Choose LM358ADGKR when the board can be requalified around the LM358 family and the replacement offers equivalent dual general-purpose operation with updated functionality. Both use an 8-pin VSSOP arrangement, but procurement and thermal requalification still require controlled engineering approval.
Is LM258ADGKR suitable for 24 V industrial sensor conditioning?
Yes, the LM258ADGKR is well suited to 24 V industrial signal-conditioning stages because it supports supply voltages up to 32 V and its common-mode input range includes ground. A typical application divides a 0 V to 5 V sensor signal, amplifies it with the appropriate noise-gain network, and interfaces the result to a converter or analog-to-digital converter. Input protection and transient suppression are still required when the sensor wiring leaves the enclosure.
What is the best ON Semiconductor equivalent for LM258ADGKR?
A valid ON Semiconductor equivalent must be checked for the exact VSSOP footprint and pin arrangement before use. The documented LM358-family references indicate that pin-compatible general-purpose dual op amps commonly share the same functional arrangement, but package codes and electrical limits differ between manufacturers. For LM258ADGKR, verify the candidate's maximum supply voltage, input offset voltage, common-mode range, output swing, and operating temperature against the original circuit requirements.
How much bypass capacitance does the LM258ADGKR need?
Place a 100 nF ceramic bypass capacitor close to pin 8 and a second 100 nF capacitor near pin 4, with both connected to the appropriate supply and ground planes. Follow the Texas Instruments LM258A datasheet typical-application guidance for decoupling and stable feedback layouts. Extra bulk capacitance can be added near the regulator output, but long supply traces between the capacitor and the device increase the likelihood of oscillation.
Does the LM258ADGKR support rail-to-rail output?
No. The LM258ADGKR does not provide a rail-to-rail output stage. Its output must remain above the lower saturation region and below the upper output limit set by the supply voltage and load current. This matters most in low-voltage designs where a 3 V or 5 V supply leaves little headroom. Use the Texas Instruments LM258A datasheet output-voltage and output-current curves to confirm the operating point.
Where can I buy LM258ADGKR online and check current stock?
Use the Request a Quote form on this page to request current LM258ADGKR availability, lead time, and commercial terms for the exact 8-pin VSSOP orderable. The Texas Instruments orderable page and distributor listings identify LM258ADGKR as an 8-pin VSSOP general-purpose dual amplifier. Give the requester the complete MPN, including the DGK package code, to avoid confusion with LM258 variants in other packages.
What is the lead time for LM258ADGKR?
Current lead time for LM258ADGKR should be requested through the Request a Quote form on this page. The manufacturer product page identifies the part as an 8-pin VSSOP orderable within the LM258A family. Provide the required quantity, date code preference, and target date with the request so current manufacturing and logistics status can be confirmed for the exact MPN.
What is the price of LM258ADGKR?
Submit an LM258ADGKR inquiry through the Request a Quote form on this page for the current commercial quotation. Pricing can depend on order quantity, date code, packaging, market conditions, and inventory status, so a single figure may not represent the current market. Use the complete LM258ADGKR MPN and the 8-pin VSSOP DGK designation when requesting the quotation.
Is LM258ADGKR currently in stock?
Current inventory for LM258ADGKR should be confirmed through the Request a Quote form on this page. Texas Instruments lists LM258ADGKR as an orderable 8-pin VSSOP configuration, while distributor availability can change independently of manufacturer production status. The quote request captures the quantity and timing needed for a meaningful stock confirmation.

داتای سەرچاوەی ئەندازیاری بۆ LM258ADGKR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM258ADGKR for new or existing designs that specifically require the LM258A device identity, a 3 mV maximum offset grade, and operation from 3 V to 32 V. Its dual 700 kHz channels and 8-pin VSSOP package are appropriate for 24 V industrial sensors, audio preamplification, control loops, and near-ground signal monitoring. Select LM358ADGKR when a board is being requalified around the LM358 family and its documented drop-in relationship with upgraded functionality is acceptable. Select LM2904DGKR when lower input offset or operation across a wider industrial temperature range is more valuable than preserving the LM258A grade. Before substituting any part, verify the package drawing, pin numbering, supply limits, input common-mode range, output swing, load capability, temperature grade, and stability at the actual feedback network.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM358ADGKR LM2904DGKR
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-pin VSSOP (DGK) 8-pin VSSOP (DGK) - same footprint 8-pin VSSOP (DGK) - same footprint
Number of Amplifiers 2 2 2
Maximum Total Supply Voltage 30 V 30 V 30 V
Supply Voltage Range 3 V to 32 V 3 V to 30 V 3 V to 30 V
Typical Gain-Bandwidth Product 700 kHz 700 kHz 700 kHz
Typical Slew Rate 0.3 V/µs 0.3 V/µs 0.3 V/µs
Maximum Input Offset Voltage 3 mV 3 mV 1 mV
Operating Temperature Range -25°C to 85°C -40°C to 85°C -40°C to 125°C
Input Common-Mode Range Includes ground Includes ground Includes ground

جیاکەرەوە سەرەکییەکان

  • Maintains a 30 V maximum total supply rating with dual general-purpose channels (بەراورد بەLM358ADGKR)
  • Lower maximum input offset voltage than the LM258A grade (بەراورد بەLM258ADGKR)
  • Broader temperature coverage for industrial deployments (بەراورد بەLM258ADGKR)

تێبینییەکانی دیزاین

Place a 100 nF ceramic bypass capacitor directly between pin 8 and the ground plane, and a second 100 nF capacitor between pin 4 and the ground plane. Keep both connections short and route them away from high-current switching nodes. The small VSSOP package makes trace length and ground-return continuity important; a long connection between the capacitor and the supply pin can create inductive feedback and instability.

Do not assume a rail-to-rail output at 3 V or 5 V. The LM258 output must remain above its lower saturation boundary and below the upper load-dependent limit. At a 5 V supply, this restricts the practical output range even though the input common-mode range includes ground. Use the output-voltage curves in the Texas Instruments LM258A datasheet and include tolerance for load current and temperature.

Keep the inverting-input and feedback-node copper areas small, and route output signals away from the non-inverting inputs to reduce coupling. Place input-resistor networks close to the device pins and keep high-impedance input traces short. The 700 kHz bandwidth is sufficient for low-frequency loops, but high-capacitance cable loads or long sensor wiring may require isolation resistors and input clamps.

Calculate the maximum total supply voltage for the installed system, including transients from relays, motors, or inductive loads. Although the LM258ADGKR supports a wide supply range, automotive and industrial transients can exceed the device limit. Use appropriate supply filtering and protection rather than relying on the amplifier's high supply-voltage tolerance as a substitute for transient suppression.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer identifies LM258ADGKR as an 8-pin VSSOP orderable in the LM258A family. RoHS, REACH, halogen-free, lead-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation or material declaration.

داتا پشتڕاستکراوەتەوە لە: 2026-11-20 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm258adgkr datasheet lm258adgkr datasheet pdf LM258ADGKR pinout LM258ADGKR specifications Texas Instruments LM258ADGKR LM258ADGKR VSSOP-8 LM258ADGKR replacement LM258ADGKR equivalent LM258ADGKR vs LM358ADGKR LM258ADGKR price LM258ADGKR stock LM258ADGKR application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM258ADGKR LM258A LM358ADGKR LM2904DGKR operational amplifier op amp dual amplifier voltage-feedback amplifier analog integrated circuit VSSOP-8 DGK package surface mount gain-bandwidth product slew rate input offset voltage input bias current common-mode input range single-supply operation split-supply operation signal conditioning sensor conditioning audio preamplifier industrial control RoHS
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ