LM258ADGKR - Dual 30V 700kHz Op Amp | Texas Instruments
部品番号: LM258ADGKR ✓ 生産中LM258ADGKR 概要
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM258 belongs to the general-purpose amplifier family within the broader voltage-feedback amplifier hierarchy. Its frequency compensation is internal, allowing each channel to operate as a stable closed-loop amplifier without an external compensation capacitor.
The two channels feature a typical slew rate of 0.3 V/µs, low supply-current drain of approximately 0.7 mA, and low input bias current. Each amplifier can operate from a single supply or from split supplies. The common-mode input range includes ground, which supports direct sensing of signals near the negative rail and makes the device useful in battery-powered monitoring circuits.
Common applications include low-frequency sensor conditioning, transducer amplification, audio preamplification, analog signal filtering, and general control loops. Because the LM258ADGKR provides more supply-voltage headroom than many modern rail-to-rail amplifiers, it remains useful when signals exceed 12 V or when a single supply of 24 V must be accommodated. The output stage does not rail-to-rail swing, so output-headroom calculations are required at the chosen supply voltage.
When designing a new board, use a 100 nF bypass capacitor close to each supply pin and verify output swing, load current, stability, and common-mode range at the actual signal amplitude. Confirm that the amplifier output remains above the lower saturation limit and below the upper load-dependent limit.
This page combines manufacturer specifications, package details, drop-in replacement options, application guidance, and practical design notes to support component selection and PCB implementation.
ドロップイン代替品: LM258ADGKR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LM258ADGKR (同一形状・フットプリント) — 相違点: Amplifier Type, Maximum Supply Voltage, Number of Channels, Operating Temperature Range, Package.
LM358ADGKR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM2904DGKR
✅ ドロップイン価格はお問い合わせください
データシートを見る →LM258ADGKR 最大定格&電気的特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 |
| Number of Amplifiers | 2 |
| Maximum Total Supply Voltage | 30 V |
| Supply Voltage Range | 3 V to 32 V |
| Typical Gain-Bandwidth Product | 700 kHz |
| Typical Slew Rate | 0.3 V/µs |
| Maximum Input Offset Voltage | 3 mV |
| Typical Input Bias Current | 40 nA |
| Typical Supply Current | 0.7 mA |
| 電源電流 | 800 µA |
| Typical Output Current per Channel | 30 mA |
| 動作温度範囲 | -25°C to 85°C |
| Input Common-Mode Range | Includes ground |
| Compensation | Internal |
| Supply Configuration | Single or split supply |
| パッケージ | 8-pin VSSOP (DGK) |
| 実装タイプ | Surface mount |
LM258ADGKR ピン構成
| ピン 1 | OUT1 — Output of amplifier 1 |
| ピン 2 | IN1- — Inverting input of amplifier 1 |
| ピン 3 | IN1+ — Non-inverting input of amplifier 1 |
| ピン 4 | V- — Negative supply connection |
| ピン 5 | IN2+ — Non-inverting input of amplifier 2 |
| ピン 6 | IN2- — Inverting input of amplifier 2 |
| ピン 7 | OUT2 — Output of amplifier 2 |
| ピン 8 | V+ — Positive supply connection |
主な用途
LM258ADGKR の用途: 6 件s: 24 V Industrial Sensor Conditioning, Audio Preamplifier Stage, Power-Supply Feedback Control, Transducer Bridge Amplifier, Battery and Portable Monitor, Analog Control and Filter Stage.
24 V Industrial Sensor Conditioning
The LM258ADGKR fits 24 V industrial sensor-conditioning circuits because it operates across a 3 V to 32 V supply range and its common-mode input includes ground. Place it between a resistive divider or transmitter interface and an analog-to-digital converter. The 700 kHz gain-bandwidth product provides margin for moderate-gain stages, while 0.3 V/µs slew rate suits low-frequency process signals. Protection networks, an input common-mode check, and output-headroom analysis remain essential because the amplifier is not rail-to-rail.
おすすめ
Audio Preamplifier Stage
The LM258ADGKR can serve as a general-purpose audio preamplifier for low-frequency and microphone-level signals when a rail-to-rail output is unnecessary. Its dual configuration allows one channel to amplify the audio input while the other handles a monitoring or bias function. The 3 mV maximum input offset voltage is modest for precision audio paths, so gain-network resistor matching should be checked for channel-to-channel offset. Output swing must remain within the supply limit at the selected load.
おすすめ
Power-Supply Feedback Control
The LM258ADGKR is appropriate for slow feedback loops in regulated power supplies because it accepts a wide supply range and provides two amplifiers for error amplification and auxiliary functions. Its 700 kHz bandwidth is sufficient for many control loops that do not require a modern high-speed error amplifier. Compensation must be recalculated when the feedback network changes, and the output must be kept above the saturation region. The device also tolerates higher supply voltages than typical 3.3 V and 5 V amplifiers.
おすすめ
Transducer Bridge Amplifier
The LM258ADGKR can amplify the low-level differential output of resistive bridges and passive transducers when the signal bandwidth is well below 700 kHz. Its two channels may support differential excitation control and differential sensing, although offset and bias-current matching should be reviewed in the final schematic. The common-mode input range including ground helps with near-ground bridge outputs. Add input clamps and EMI filtering on long sensor cables to prevent overload and transient damage.
おすすめ
Battery and Portable Monitor
The LM258ADGKR is useful in battery-operated monitors because it operates from a single supply down to 3 V and its common-mode input range extends to ground. It can monitor a divided supply or sensor signal while operating directly from a low-voltage cell. The low typical supply-current drain of 0.7 mA supports battery conservation, although the complete circuit budget must include divider, reference, and protection leakage. Verify output headroom because the output does not swing fully to either rail.
おすすめ
Analog Control and Filter Stage
The LM258ADGKR supports active filters, integrators, and slow proportional-control loops where the signal bandwidth remains below the device's 700 kHz gain-bandwidth product. Internal frequency compensation enables straightforward inverting and non-inverting configurations. Component tolerances in the feedback network directly affect gain and cutoff accuracy, so 1% resistors are usually preferable for repeatable production behavior. Validate stability with the actual load and output-bias conditions rather than relying only on nominal gain calculations.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LM258ADGKR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LM358ADGKR | LM2904DGKR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin VSSOP (DGK) | 8-pin VSSOP (DGK) - same footprint | 8-pin VSSOP (DGK) - same footprint |
| Number of Amplifiers | 2 | 2 | 2 |
| Maximum Total Supply Voltage | 30 V | 30 V | 30 V |
| Supply Voltage Range | 3 V to 32 V | 3 V to 30 V | 3 V to 30 V |
| Typical Gain-Bandwidth Product | 700 kHz | 700 kHz | 700 kHz |
| Typical Slew Rate | 0.3 V/µs | 0.3 V/µs | 0.3 V/µs |
| Maximum Input Offset Voltage | 3 mV | 3 mV | 1 mV |
| Operating Temperature Range | -25°C to 85°C | -40°C to 85°C | -40°C to 125°C |
| Input Common-Mode Range | Includes ground | Includes ground | Includes ground |
主な差別化要因
- Maintains a 30 V maximum total supply rating with dual general-purpose channels (vs LM358ADGKR)
- Lower maximum input offset voltage than the LM258A grade (vs LM258ADGKR)
- Broader temperature coverage for industrial deployments (vs LM258ADGKR)
設計ノート
Place a 100 nF ceramic bypass capacitor directly between pin 8 and the ground plane, and a second 100 nF capacitor between pin 4 and the ground plane. Keep both connections short and route them away from high-current switching nodes. The small VSSOP package makes trace length and ground-return continuity important; a long connection between the capacitor and the supply pin can create inductive feedback and instability.
Do not assume a rail-to-rail output at 3 V or 5 V. The LM258 output must remain above its lower saturation boundary and below the upper load-dependent limit. At a 5 V supply, this restricts the practical output range even though the input common-mode range includes ground. Use the output-voltage curves in the Texas Instruments LM258A datasheet and include tolerance for load current and temperature.
Keep the inverting-input and feedback-node copper areas small, and route output signals away from the non-inverting inputs to reduce coupling. Place input-resistor networks close to the device pins and keep high-impedance input traces short. The 700 kHz bandwidth is sufficient for low-frequency loops, but high-capacitance cable loads or long sensor wiring may require isolation resistors and input clamps.
Calculate the maximum total supply voltage for the installed system, including transients from relays, motors, or inductive loads. Although the LM258ADGKR supports a wide supply range, automotive and industrial transients can exceed the device limit. Use appropriate supply filtering and protection rather than relying on the amplifier's high supply-voltage tolerance as a substitute for transient suppression.
コンプライアンス情報
The manufacturer identifies LM258ADGKR as an 8-pin VSSOP orderable in the LM258A family. RoHS, REACH, halogen-free, lead-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation or material declaration.