Texas Instruments

LM2902KAVQPWRG4 - Quad 30V 1.2MHz Op Amp | Texas Instruments

MPN: LM2902KAVQPWRG4 ✓ چالاک
30 V Vdss 14-pin TSSOP (PW) Package
MOQ: 1 |

LM2902KAVQPWRG4 گشتی

Texas Instruments LM2902KAVQPWRG4 is a four-circuit operational amplifier in a 14-pin TSSOP (PW) package. The device supports supply voltages up to 30 V, operates across a 1.2 MHz gain-bandwidth product, and provides a 2 mV input offset voltage. Its four amplifiers are designed for general-purpose analog signal conditioning across industrial, automotive, and instrumentation systems.

An operational amplifier is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. A quad operational amplifier combines four amplifiers in one package, allowing a board to implement four independent gain, buffering, filtering, comparison, or current-voltage conversion functions while reducing package count and simplifying power distribution.

The LM2902KAV family provides a 3 V to 36 V supply range, a 1.2 MHz gain-bandwidth product, and input offset voltage as low as 2 mV in the BA version. The target MPN is associated with improved ESD protection of 2 kV and automotive qualification for AEC-Q100 applications. The 14-pin TSSOP package also supports operation from -40°C to +125°C.

Each amplifier contains differential input and output stages with substantial open-loop gain. When feedback is applied, the closed-loop gain is established by external resistors rather than by the intrinsic open-loop gain. Suitable external compensation and output bypassing must be selected according to the operating mode, load, and gain because stability requirements vary with circuit topology.

Typical uses include current-sensing amplifiers, sensor signal conditioning, low-frequency active filters, level-shift and reference buffers, industrial sensor interfaces, and automotive control modules. The four independent channels also reduce board area when several low-frequency analog functions are required near one another.

For layout, keep input and feedback connections short, place compensation or bypass components close to their associated pins, and avoid routing high-current or switching signals alongside sensitive input traces. Confirm common-mode and output-swing limits at the actual supply voltage, and verify stability with the intended load and cable capacitance before production release.

This page organizes the manufacturer specifications, package information, application guidance, and same-footprint ordering alternatives into one engineering reference. It also highlights where automotive qualification and ESD protection affect replacement decisions, helping designers distinguish genuine board-level drop-ins from merely similar quad operational amplifiers.

جێگرەوەکانی جێگۆڕکێ بۆ LM2902KAVQPWRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902KAVQPWRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Input Offset Voltage, Package, Amplifier Type, ESD Protection, Maximum Supply Voltage.

Texas Instruments
Input Offset Voltage: 2 mV maximum for BA version; 600 uV typical for family
Package: 14-pin TSSOP
Amplifier Type: General-purpose operational amplifier
بەراوردکردن لەگەڵ LM2902KAVQPWRG4 →
Texas Instruments
Input Offset Voltage: 2 mV
Amplifier Type: Quad general-purpose operational amplifier
ESD Protection: 2 kV
بەراوردکردن لەگەڵ LM2902KAVQPWRG4 →
Texas Instruments
Input Offset Voltage: 2 mV
Package: 14-pin TSSOP
بەراوردکردن لەگەڵ LM2902KAVQPWRG4 →

LM2902KAVQPWR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 14-pin TSSOP (PW)
4 circuits · General-purpose operational amplifier · 1.2 MHz · 2 mV maximum for BA version; 600 uV typical for family · 2 kV for K-suffix devices · Up to 26 V · Plus-and-minus 13 V · 3 V to 36 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902KAVQPWR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 14-pin TSSOP (PW)
4 circuits · General-purpose operational amplifier · 1.2 MHz · 2 mV maximum for BA version; 600 uV typical for family · 2 kV for K-suffix devices · Up to 26 V · Plus-and-minus 13 V · 3 V to 36 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2902KAVQPWRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Count 4 circuits
Product Type Quad operational amplifier
Maximum Supply Voltage 30 V
Family Supply Voltage Range 3 V to 36 V
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 2 mV maximum
Improved ESD Protection 2 kV
مەودای پلەی گەرمیی کارکردن -40°C to +125°C
پاکێج 14-pin TSSOP (PW)
ژمارەی پین 14 pins
جۆری دامەزراندن Surface mount
Automotive Qualification AEC-Q100 qualified

ڕێکخستنی پینی LM2902KAVQPWRG4

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
پین 1 OUT1 — Output of amplifier 1
پین 2 IN1- — Inverting input of amplifier 1
پین 3 IN1+ — Non-inverting input of amplifier 1
پین 4 V+ — Positive supply connection
پین 5 IN2+ — Non-inverting input of amplifier 2
پین 6 IN2- — Inverting input of amplifier 2
پین 7 OUT2 — Output of amplifier 2
پین 8 OUT3 — Output of amplifier 3
پین 9 IN3- — Inverting input of amplifier 3
پین 10 IN3+ — Non-inverting input of amplifier 3
پین 11 V- — Negative supply connection
پین 12 IN4+ — Non-inverting input of amplifier 4
پین 13 IN4- — Inverting input of amplifier 4
پین 14 OUT4 — Output of amplifier 4

بەکارهێنانە باوەکان

LM2902KAVQPWRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Signal Conditioning, Automotive Control Module Interfaces, Active Low-Frequency Filtering, Precision Current Sensing, Instrumentation Buffering, Audio and Communication Interface Circuits.

🏭

Industrial Sensor Signal Conditioning

The LM2902KAVQPWRG4 fits industrial sensor interfaces that require amplification and buffering of low-frequency signals from transducers, resistive bridges, or external sensing modules. Four amplifiers in one 14-pin TSSOP package allow a controller board to combine signal conditioning, active filtering, and reference buffering while limiting board area. Its 1.2 MHz gain-bandwidth product is appropriate for bandwidths well below the unity-gain limit, while the 2 mV input offset specification helps preserve accuracy in high-gain stages. The -40°C to +125°C operating range supports demanding industrial environments, and 2 kV improved ESD protection adds useful robustness at externally accessible amplifier inputs. Confirm the sensor output remains inside the input common-mode range and add filtering at high-impedance sources.

🚗

Automotive Control Module Interfaces

LM2902KAVQPWRG4 is appropriate for low-frequency analog channels in automotive electronic control modules, including actuator feedback, sensor conditioning, and buffered voltage references. Its AEC-Q100 qualification and 2 kV improved ESD protection distinguish the G4 configuration for automotive program requirements. The four internal amplifiers allow several independent analog functions to share a common supply and reduce component count. With a 1.2 MHz gain-bandwidth product, the device suits filters and amplifiers operating well below its unity-gain bandwidth, including slow sensor and vehicle-network interfaces. The -40°C to +125°C rating covers automotive temperature requirements. Designers must still verify transient protection, common-mode limits, channel-to-channel behavior, and the exact qualification requirements for the completed module.

🔧

Active Low-Frequency Filtering

The LM2902KAVQPWRG4 can implement active low-pass, high-pass, or band-pass filter stages where a 1.2 MHz gain-bandwidth product provides more bandwidth than the signal path requires. Its four amplifiers permit a second-order filter using one stage and leave three channels available for gain, buffering, or offset correction. The 2 mV input offset voltage is particularly useful when higher closed-loop gain magnifies both signal and offset. Four independent amplifiers in a compact 14-pin TSSOP also reduce routing complexity compared with separate single-amplifier packages. Component tolerances, capacitor selection, and op-amp noise will often determine filter accuracy more than the nominal bandwidth. Validate stability and frequency response across the intended supply voltage and load because compensation requirements change with closed-loop gain.

⚡

Precision Current Sensing

The LM2902KAVQPWRG4 can amplify the small voltage generated by a shunt resistor in low-to-moderate current measurement systems. A 2 mV input offset specification is valuable when the shunt voltage is close to the amplifier's noise and offset limits, while the 1.2 MHz gain-bandwidth product supports control loops and diagnostics above very low frequencies. Four channels allow one amplifier to sense current while the others provide gain, filtering, or reference buffering. For high-current switching systems, Kelvin connections and careful shunt placement are necessary to prevent IR gradients from appearing as measurement error. The amplifier's common-mode and output-swing limits must be checked against the shunt voltage and selected gain, and input filtering may be required when switching nodes are electrically close to the sense traces.

📺

Instrumentation Buffering

The LM2902KAVQPWRG4 is suitable for instrumentation buffers, sensor outputs, and reference nodes where high input impedance prevents the source from being loaded. A follower configuration provides isolation between a sensor and subsequent conversion or filtering stages, while the 1.2 MHz bandwidth supports signals well below the amplifier's upper frequency limit. Its 2 mV offset specification contributes little error when configured for unity gain. Four channels allow buffering of multiple measurement inputs without requiring four separate packages, and the 14-pin TSSOP footprint simplifies routing in compact instrumentation. Bias-current effects can become significant with very high source impedances, so use the datasheet's input bias and noise characteristics during impedance planning. Keep sensitive traces short and shield them from adjacent power-converter currents.

🌐

Audio and Communication Interface Circuits

LM2902KAVQPWRG4 can support low-frequency audio, communications, and general interface functions such as gain stages, buffers, and crossover networks. The 1.2 MHz gain-bandwidth product is sufficient for many voice-band and low-rate communication signals, while four amplifiers allow two stereo channels or several single-ended functions to share one package. Its 2 mV input offset helps reduce unwanted DC shift in inverting or high-gain stages. The device should not be interpreted as a high-performance audio amplifier: output-current capability, distortion, noise density, and load drive must be checked against the intended impedance and bandwidth. In communications equipment, keep input and feedback routes away from switching supplies and clocks, and use grounded reference geometry to minimize noise coupling into the signal path.

کورتەی بەرهەمە پێشنیارکراوەکان

LM2902DG onsemi بەکارهێنراوە لە: Industrial Sensor Signal Conditioning, Active Low-Frequency Filtering, Instrumentation Buffering LM2902PT Related Texas Instruments quad operational amplifier requiring package verification بەکارهێنراوە لە: Industrial Sensor Signal Conditioning, Precision Current Sensing, Audio and Communication Interface Circuits LM2902KAVQPWR Texas Instruments بەکارهێنراوە لە: Automotive Control Module Interfaces, Active Low-Frequency Filtering, Precision Current Sensing, Audio and Communication Interface Circuits LM2902KAVQPW Same-family 14-pin PW operational amplifier without the G4 suffix بەکارهێنراوە لە: Automotive Control Module Interfaces, Instrumentation Buffering
What is the operating voltage of LM2902KAVQPWRG4?
The LM2902KAVQPWRG4 supports a supply range up to 30 V for the target device, while the manufacturer identifies a 3 V to 36 V range for the LM2902B and LM2902BA family versions. According to the Texas Instruments LM2902KAV product page and manufacturer datasheet, the exact minimum and maximum limits for the selected ordering code should be confirmed against the supply-voltage table before connecting the device.
What are the key specifications of LM2902KAVQPWRG4 that engineers should know?
The LM2902KAVQPWRG4 is a four-circuit operational amplifier with a 30 V maximum supply rating, 1.2 MHz gain-bandwidth product, 2 mV input offset voltage, 2 kV improved ESD protection, and AEC-Q100 automotive qualification. It is packaged in a 14-pin TSSOP (PW) package for a -40°C to +125°C operating range. These specifications make it appropriate for low-frequency industrial, instrumentation, sensor-interface, and automotive signal-conditioning circuits.
Where can I download the LM2902KAVQPWRG4 datasheet PDF?
The LM2902KAVQPWRG4 datasheet can be obtained through the Texas Instruments LM2902KAV product page and the LM2902 family datasheet. The manufacturer datasheet contains the ordering information, electrical characteristics, pin configuration, typical performance curves, and application guidance. Use the orderable part details page to distinguish the 14-pin PW package and the automotive-qualified G4 ordering code from other LM2902 package variants.
Where can I find the LM2902KAVQPWRG4 pinout?
The LM2902KAVQPWRG4 pin configuration is shown in the pin-configuration section of the Texas Instruments manufacturer datasheet. The device uses four operational amplifiers in a 14-pin TSSOP (PW) package, with each amplifier using two input pins and one output pin, plus shared supply pins. Assign PCB tracks from the numbered package drawing rather than relying only on amplifier ordering within the package.
Can LM2902KAVQPWRG4 replace LM2902KAVQPWR?
Yes, LM2902KAVQPWRG4 is a same-family ordering option for LM2902KAVQPWR when the board uses the 14-pin PW footprint and the electrical requirements remain unchanged. Both identify a 1.2 MHz quad operational amplifier with 2 mV offset voltage and 2 kV ESD capability. The G4 version is identified as AEC-Q100 qualified for automotive applications, so procurement should confirm the required qualification and environmental controls.
What is the best drop-in replacement for LM2902KAVQPWRG4?
LM2902KAVQPWR is the closest documented same-brand drop-in candidate because it uses the same 14-pin PW package and the same 1.2 MHz, 2 mV-offset LM2902KAV electrical family. LM2902KAVQPW is another same-package ordering option. Verify the required automotive qualification, tape-and-reel orientation, production configuration, and lifecycle requirements before substituting any ordering code into an approved design.
LM2902KAVQPWRG4 vs LM2902KAVQPWR - which is better for automotive use?
LM2902KAVQPWRG4 is the better choice for a design that specifically requires the automotive-qualified G4 configuration. Both parts use the 14-pin TSSOP (PW) footprint and are based on the 1.2 MHz LM2902KAV family with 2 mV input offset voltage and 2 kV ESD protection. For industrial or consumer products, LM2902KAVQPWR may be acceptable when automotive qualification is not required.
When should I choose LM2902KAVQPWRG4 over a generic LM2902?
Choose LM2902KAVQPWRG4 when the design needs a 14-pin PW quad operational amplifier, operation across -40°C to +125°C, 2 kV improved ESD protection, and AEC-Q100 automotive qualification. A generic LM2902 in a different package cannot be soldered directly onto the same footprint without PCB changes. Even a similarly packaged part should be checked for offset voltage, bandwidth, supply range, common-mode range, and qualification.
Is LM2902KAVQPWRG4 suitable for sensor signal conditioning?
Yes, LM2902KAVQPWRG4 is suitable for many low-frequency sensor signal-conditioning applications because it provides four amplifiers, a 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage. Its -40°C to +125°C range and 2 kV ESD protection also support demanding industrial and automotive environments. Check the input common-mode range against the sensor output and include input filtering for high-impedance sources.
Can LM2902KAVQPWRG4 drive a capacitive load?
The LM2902KAVQPWRG4 can be used with capacitive loads only within the stability limits established by the manufacturer datasheet. The exact maximum capacitive load and recommended isolation resistance are not stated in the product summary, so the relevant graph and application guidance must be checked before connecting long sensor cables or large filter capacitors. Shorter feedback traces and an isolation resistor can improve stability.
How should I decouple the LM2902KAVQPWRG4 power supply?
Place the manufacturer-recommended supply bypass capacitor close to the positive and negative supply pins, and keep the return-current path short. Decoupling requirements depend on supply impedance, source distance, and the noise present on the power rail. Avoid placing sensitive input traces beside the capacitor return path, and follow the datasheet reference layout to minimize supply-to-output coupling through the shared ground connection.
What is the difference between LM2902KAVQPWRG4 and LM2902KAVQPW?
LM2902KAVQPWRG4 and LM2902KAVQPW share the LM2902KAV electrical family and 14-pin PW package, but their ordering and qualification details differ. The G4 part is identified as AEC-Q100 qualified for automotive applications and is supplied as the G4 ordering configuration. The PW code identifies the same TSSOP package family without the G4 qualification suffix, so procurement documentation should confirm the exact qualification and delivery configuration required.
Where to buy LM2902KAVQPWRG4 online?
Use the Request a Quote form on this page to request LM2902KAVQPWRG4 availability, lead time, and order quantities from XAIPART. The request should include the exact 14-pin PW package configuration and whether the automotive-qualified G4 version is mandatory. This approach keeps the inquiry tied to the specific ordering code rather than a broader LM2902 family listing.
What is the price of LM2902KAVQPWRG4?
Current LM2902KAVQPWRG4 pricing is handled through the Request a Quote form on this page rather than through a static price statement. Submit the required quantity, delivery location, packaging preference, and automotive qualification requirements. The quote team can then confirm the current commercial terms for the exact LM2902KAVQPWRG4 ordering code.
What is the lead time for LM2902KAVQPWRG4?
The current lead time and minimum order quantity for LM2902KAVQPWRG4 should be requested through the Request a Quote form on this page. Include the required quantity, date code policy, shipping destination, and whether production traceability or automotive qualification records are needed. These details allow the order to be checked against the exact 14-pin PW G4 configuration instead of a generic LM2902 family order.
Is there a cross-brand drop-in replacement for LM2902KAVQPWRG4?
No cross-brand part is listed as a confirmed 14-pin TSSOP drop-in replacement for LM2902KAVQPWRG4 in the manufacturer and cross-reference information reviewed for this page. LM2902DG and LM2902PT are related quad operational amplifiers, but their package and pin arrangements must be checked before considering a board redesign. For a genuine no-rework replacement, use only a part whose manufacturer confirms the same PW footprint, pinout, supply limits, and qualification requirements.

داتای سەرچاوەی ئەندازیاری بۆ LM2902KAVQPWRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM2902KAVQPWRG4 for automotive or industrial designs that require four low-frequency amplifiers in the 14-pin TSSOP PW footprint, AEC-Q100 qualification, improved 2 kV ESD protection, and operation from -40°C to +125°C. LM2902KAVQPWR is the closest same-family option when the exact core electrical ratings and package are required but the G4 automotive qualification is not. LM2902KAVQPW can also reuse the same board footprint, although the absence of the G4 suffix requires careful review of qualification and ordering requirements. LM2902DG and LM2902PT are useful functional comparisons but should not be treated as drop-in parts without confirming their package dimensions and pin assignments. For any substitution, verify supply voltage, common-mode range, output swing, offset voltage, bandwidth, load stability, channel layout, and qualification before releasing the PCB.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2902KAVQPWR LM2902KAVQPW
Package 14-pin TSSOP (PW) 14-pin TSSOP (PW) 14-pin TSSOP (PW)
Brand Texas Instruments Texas Instruments Texas Instruments
Amplifier Count 4 circuits 4 circuits 4 circuits
Maximum Supply Voltage 30 V 30 V 30 V
Gain-Bandwidth Product 1.2 MHz 1.2 MHz 1.2 MHz
Input Offset Voltage 2 mV 2 mV 2 mV
Improved ESD Protection 2 kV 2 kV 2 kV
Pin Count 14 pins 14 pins 14 pins

جیاکەرەوە سەرەکییەکان

  • Automotive-qualified G4 configuration (بەراورد بەLM2902KAVQPWR)
  • Four-channel integration in a 14-pin package (بەراورد بەLM2902KAVQPW)
  • Improved ESD capability (بەراورد بەLM2902KAVQPW)
  • Same-footprint second-source option (بەراورد بەLM2902KAVQPWR)

تێبینییەکانی دیزاین

Place the supply bypass capacitor next to the V+ and V- pins, with a short and low-inductance return path to the device ground. Keep amplifier inputs and feedback components away from switching nodes and power-conductor edges. Use the manufacturer datasheet layout as the basis for the PCB because the four channels share supply pins, so trace geometry around one channel can affect noise and stability in the others.

Do not assume every LM2902 ordering code is a footprint-compatible replacement. LM2902DG and LM2902PT are related quad amplifiers, but their packages and pin arrangements require verification and may require PCB changes. A true no-rework replacement must use the 14-pin PW footprint, provide compatible supply and signal pins, and meet the required automotive qualification and ESD requirements.

For high-impedance sources, minimize input-trace length and capacitance, keep the feedback resistor close to the relevant output, and use guarding where leakage can affect accuracy. At higher closed-loop gain, verify the compensation network against the manufacturer guidance and intended capacitive load. Long sensor cables may require input protection or filtering, but added capacitance can reduce stability and should be evaluated electrically.

Check output swing and input common-mode limits at the lowest and highest supply voltages used by the design; the 30 V maximum rating does not guarantee linear operation at every intermediate supply condition. For dual-supply operation, account for the negative-rail limitations of the selected LM2902 variant. Avoid driving loads beyond the output-current and stability characteristics listed for the exact ordering code in the manufacturer datasheet.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The target MPN is identified as AEC-Q100 qualified for automotive applications. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly established by the manufacturer information reviewed for this product.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2902KAVQPWRG4 datasheet LM2902KAVQPWRG4 pinout LM2902KAVQPWRG4 datasheet pdf LM2902KAVQPWRG4 equivalent LM2902KAVQPWRG4 replacement LM2902KAVQPWRG4 vs LM2902KAVQPWR Texas Instruments LM2902KAVQPWRG4 LM2902KAVQPWRG4 30V 1.2MHz LM2902KAVQPWRG4 TSSOP-14 LM2902KAVQPWRG4 automotive op amp LM2902KAVQPWRG4 sensor signal conditioning LM2902KAVQPWRG4 price LM2902KAVQPWRG4 stock LM2902KAVQPWRG4 footprint LM2902KAVQPWRG4 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM2902KAVQPWRG4 LM2902KAVQPWR LM2902KAVQPW LM2902DG LM2902PT operational amplifier quad operational amplifier analog amplifier signal conditioner active filter current-sense amplifier voltage buffer LM2902KAV family TSSOP-14 PW package surface-mount package AEC-Q100 automotive qualification ESD protection input offset voltage gain-bandwidth product sensor interface industrial control automotive electronics
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ