LM2902KAVQPWR - 30V Quad Op Amp with 2kV ESD | Texas Instruments
MPN: LM2902KAVQPWR ✓ چالاکLM2902KAVQPWR گشتی
An operational amplifier, or op amp, is a high-gain differential-input amplifier that uses external feedback to set closed-loop gain. The LM2902KAV family belongs to the broader hierarchy of analog amplifiers, analog signal-processing ICs, and semiconductors. Four independent amplifiers in one package reduce component count and board area in designs that require multiple sensing, buffering, or gain stages.
Key electrical characteristics include a 1.2 MHz gain-bandwidth product, 2 mV maximum input offset voltage for the BA version, 600 uV typical offset stated for the family, and 2 kV ESD protection on the K-suffix devices. The LM2902 supply arrangement supports 26 V single-supply operation or plus-and-minus 13 V dual-supply operation. Supply-current drain is specified as low as 0.8 mA typical and remains independent of supply voltage.
The common-mode input voltage range includes ground, making the amplifier suitable for single-supply sensors whose outputs remain near 0 V. Differential input voltage capability and rail-to-rail output behavior also make the device useful in cost-sensitive analog signal chains where the output must approach supply limits. The B-generation device is positioned by Texas Instruments as a drop-in replacement for LM224, LM324, and LM2902 versions with improved specifications.
Typical uses include industrial sensor conditioning, transducer amplification, low-frequency active filters, instrumentation amplifiers, audio preamplifier stages, motor-feedback networks, and general-purpose power-control loops. Four amplifiers can implement a complete low-speed control or measurement chain in a single package.
PCB design should prioritize short feedback traces, clean grounding, and input-node protection from switching or high-energy sources. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be tied to a defined common-mode voltage rather than left floating. The 14-TSSOP package uses a narrow lead pitch, so inspect the manufacturer land pattern and solder reflow profile before assembly.
جێگرەوەکانی جێگۆڕکێ بۆ LM2902KAVQPWR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902KAVQPWR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Input Offset Voltage, Package, Amplifier Type, Maximum Supply Voltage, AEC-Q100 Qualification.
LM2902PWRG3
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902KPWG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2902PWRG3
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902KAVQPWRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902KAVQPWR زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifiers | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV maximum for BA version; 600 uV typical for family |
| ESD Protection | 2 kV for K-suffix devices |
| Single-Supply Operating Range | Up to 26 V |
| Dual-Supply Operating Range | Plus-and-minus 13 V |
| B/BA Version Supply Range | 3 V to 36 V |
| Supply-Current Drain | 0.8 mA typical |
| Common-Mode Input Voltage | Range includes ground |
| Differential Input Voltage Capability | Supported; rating not stated |
| Output Swing | Near supply rails; exact limits not stated |
| پاکێج | 14-pin TSSOP |
| جۆری دامەزراندن | Surface mount |
| Lead Pitch | 0.65 mm nominal |
| دۆخی RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not stated |
| Automotive-Grade Variant | LM2902KVQPWRQ1 identified as a separate ordering option |
ڕێنمایی ڕێکخستنی پینی LM2902KAVQPWR 14-pin tssop
ڕێکخستنی پین بۆ LM2902KAVQPWR (پاکێجی 14-pin tssop). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2902KAVQPWR.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2902KAVQPWR گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Signal Conditioning, Low-Frequency Active Filters, Motor Feedback and Control Loops, Audio Preamplifier Stages, Power-Supply Feedback and Monitoring, Battery-Powered Measurement Front Ends.
Industrial Sensor Signal Conditioning
The LM2902KAVQPWR fits four-stage industrial sensor conditioning because its common-mode input range includes ground and its supply-current drain is 0.8 mA typical. Two amplifiers can amplify differential sensor outputs, while the remaining channels can perform active filtering and level shifting. The 30 V-class device also provides headroom for 24 V industrial systems when the exact operating limits are confirmed. Compared with a low-voltage precision amplifier, this device offers a simpler, higher-voltage general-purpose solution with a 1.2 MHz gain-bandwidth product. Add input protection and filtering at connector-facing pins because 2 kV ESD protection is specified for the K-suffix device but does not replace a dedicated surge-protection network.
پێشنیارکراو
Low-Frequency Active Filters
The LM2902KAVQPWR is suitable for second- and fourth-order low-frequency active filters built from its four 1.2 MHz gain-bandwidth amplifiers. The gain-bandwidth product supports closed-loop gains where the resulting closed-loop bandwidth remains within the amplifier's operating range, while the low offset characteristic helps preserve accuracy around the signal's DC operating point. Quad-channel integration reduces the component count for cascaded filters and auxiliary gain stages. Its common-mode range including ground makes it especially useful in single-supply filter networks, provided each stage is biased within the input and output swing limits shown in the manufacturer datasheet.
پێشنیارکراو
Motor Feedback and Control Loops
The LM2902KAVQPWR can implement current-sense amplification, error amplification, and slow control-loop functions around small DC motor or actuator drivers. Its differential input voltage capability and common-mode range including ground are useful when the feedback signal is referenced near 0 V, and the 1.2 MHz gain-bandwidth product provides adequate loop bandwidth for many low-speed positioning systems. Four amplifiers permit a practical allocation to current sensing, error amplification, and output buffering. The design must verify maximum differential input voltage, output swing, supply headroom, and stability with the chosen feedback network under motor-start transients.
پێشنیارکراو
Audio Preamplifier Stages
The LM2902KAVQPWR can serve as a general-purpose audio preamplifier for low-level microphone, line, or headphone-driver input stages. Its 1.2 MHz gain-bandwidth product is sufficient for many audio-band amplification tasks, while the low input offset helps reduce DC bias at the output. Four channels allow two stereo signal paths or one stereo path plus monitoring and filtering functions. Because this is a general-purpose rather than low-noise audio amplifier, the system should evaluate noise, distortion, input bias current, and output-swing requirements against the audio specification before deployment.
پێشنیارکراو
Power-Supply Feedback and Monitoring
The LM2902KAVQPWR can supervise and condition feedback signals in linear or switched power systems where the operating voltage exceeds typical low-voltage amplifier ranges. Its common-mode input range includes ground supports sensing near 0 V, and the wide supply family gives designers margin for 24 V industrial environments. Four channels can provide overvoltage detection, current-sense amplification, and fault-logic buffering. The amplifier is not a dedicated comparator, so response time and output-saturation behavior should be checked carefully; a comparator such as LM2903DR may be preferable when only a fast threshold function is required.
پێشنیارکراو
Battery-Powered Measurement Front Ends
The LM2902KAVQPWR is appropriate for battery-powered measurement front ends when a 0.8 mA typical supply-current drain is acceptable and the circuit operates from a supply well above the amplifier's minimum requirement. Four channels can reduce package count in portable instrumentation by combining sensor amplification, filtering, reference buffering, and output conditioning. The common-mode range including ground simplifies operation from low-voltage sensor sources. Designers should account for input bias current, noise, shutdown behavior that the device family may not provide, and the effect of a high-voltage supply on total power consumption.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2902KAVQPWR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2902PWR | LM2902KPWG4 | LM2902PWRG3 | LM2902KAVQPWRQ1 |
|---|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 4 circuits | 4 channels | 4 channels | 4 channels | 4 circuits |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Automotive Ordering Option | LM2902KAVQPWR | No automotive-qualified ordering option identified | No automotive-qualified ordering option identified | No automotive-qualified ordering option identified | Automotive-ordering designation |
| Common-Mode Input Voltage Range | Includes ground | Same LM2902 family; verify exact range | Same LM2902 family; verify exact range | Same LM2902 family; verify exact range | Includes ground for the family |
| Single-Supply Maximum | 26 V | 26 V family rating | 26 V family rating | 26 V family rating | 26 V family rating |
جیاکەرەوە سەرەکییەکان
- K-suffix ESD protection (بەراورد بەLM2902PWR)
- Four independent amplifiers in a 14-pin TSSOP (بەراورد بەLM2901PWR)
- Automotive-ordering family option (بەراورد بەLM2902PWR)
- Improved BA-version offset specification (بەراورد بەLM2902PWR)
تێبینییەکانی دیزاین
Route each amplifier's input, feedback, and output paths as short as practical because long feedback loops on a general-purpose operational amplifier can pick up noise or become susceptible to oscillation. Keep the four channels spatially separable when high-gain and low-level signals share the package. Use a continuous ground plane, place the bypass capacitor at the supply pins, and follow the manufacturer's 14-TSSOP land pattern for the 0.65 mm lead pitch.
The K-suffix device provides 2 kV ESD protection, but that rating should not be treated as complete industrial surge protection. Place series resistors or dedicated protection components at connector-facing inputs when cables can expose the amplifier to large transients. Return the shield and signal reference to the same low-impedance ground region, and verify that the maximum differential input voltage remains within the datasheet limit during an ESD event.
Do not allow an unused amplifier channel to float. An unused input and output should be tied to a stable common-mode voltage within the input and output ranges while avoiding configurations that can oscillate or inject current into the supply rails. Also verify that the selected operating point is compatible with the 3 V to 36 V B/BA family range and the LM2902-specific 26 V single-supply limit.
زانیاری پابەندبوون
The standard LM2902KAVQPWR ordering information does not identify an automotive qualification. The separate LM2902KAVQPWRQ1 automotive-ordering variant is listed among the family options. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses are not stated in the available product records.