LM2902KVQPWRG4Q1 - Quad 26V Automotive Op Amp | TI
MPN: LM2902KVQPWRG4Q1 ✗ کۆتایی ژیانLM2902KVQPWRG4Q1 گشتی
An operational amplifier is a voltage-controlled differential amplifier whose high open-loop gain and feedback network create accurate, stable closed-loop behavior. The LM2902 family belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, voltage-feedback amplifiers, analog signal-conditioning ICs, and power-management system components. Four integrated channels reduce package count while preserving separate amplifier sections for sensors, actuator interfaces, diagnostics, and control loops.
The headline characteristics are a 26 V supply capability, 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage. These ratings support low-frequency control and sensing functions where a wide supply range, multiple channels, and economical integration are more important than high-speed precision. The automotive designation identifies the LM2902-Q1 family as qualified for vehicle applications, although production qualification does not by itself guarantee suitability for every vehicle subsystem.
Each amplifier is frequency compensated and intended for use with conventional negative-feedback networks. When configured as a non-inverting amplifier, the closed-loop gain is established by external resistors; when configured as an inverting amplifier, the input and feedback impedances set the signal relationship. The 1.2 MHz gain-bandwidth product leaves useful open-loop bandwidth for common audio-bandwidth, sensor-conditioning, and industrial-control loops, although exact stability and accuracy must be evaluated at the selected gain and load.
Typical uses include battery-powered sensor interfaces, vehicle body and chassis control modules, transducer conditioning, line-driver stages, low-current actuator drivers, and general-purpose signal amplification. Operating from a single supply or split supplies allows integration around sensors referenced to ground or to mid-supply. Care should be taken when driving capacitive loads or approaching supply-rail limits because output swing, input common-mode range, load current, and thermal conditions determine usable linear operation.
The TSSOP-14 footprint requires a compact surface-mount layout with adequate copper for heat dissipation. Place bypass capacitance close to the supply pins, maintain short feedback paths, and route high-impedance input nodes away from switching nodes. Because this exact orderable code is listed as no longer in production, engineers should verify availability and approved sourcing before releasing a new production design.
This product summary combines the automotive LM2902-Q1 specifications with same-footprint family alternatives, application guidance, package considerations, and a selection framework. It helps distinguish electrical and qualification differences that are not apparent from the 14-pin TSSOP package designation alone.
جێگرەوەکانی جێگۆڕکێ بۆ LM2902KVQPWRG4Q1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902KVQPWRG4Q1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Automotive Qualification, ESD Protection, Maximum Supply Voltage.
LM2902QPWRG4Q1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902KVQPWRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902PT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2902KVPT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2902KVQPWR
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902KVQPWRG4Q1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 channels |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| پاکێج | 14-pin TSSOP |
| Automotive Qualification | AEC-Q100 automotive family |
| جۆری دامەزراندن | Surface mount |
| AEC-Q100 Status | Qualified for automotive applications |
ڕێنمایی ڕێکخستنی پینی LM2902KVQPWRG4Q1 14-pin tssop
ڕێکخستنی پین بۆ LM2902KVQPWRG4Q1 (پاکێجی 14-pin tssop). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2902KVQPWRG4Q1.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2902KVQPWRG4Q1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Signal Conditioning, Body and Chassis Control Modules, Battery-Powered Sensor Interfaces, Transducer Bridge Excitation and Readback, Actuator Drive Signal Conditioning, General-Purpose Industrial Control Amplification.
Automotive Sensor Signal Conditioning
The LM2902KVQPWRG4Q1 fits automotive sensor-conditioning circuits that require several low-frequency amplifier channels on a 26 V-rated supply. Its four independent sections can amplify transducer outputs, buffer high-impedance sensor nodes, or form gain stages around control-system inputs. The 1.2 MHz gain-bandwidth product is suitable for signals well below the megahertz range, while the 2 mV offset specification helps bound input-referred error in closed-loop amplifier configurations. Because the device is from the LM2902-Q1 automotive family, it is intended for vehicle electronic systems that require controlled environmental qualification. Final validation should include the sensor output range, common-mode limits, output swing, transient protection, and fault behavior.
پێشنیارکراو
Body and Chassis Control Modules
The LM2902KVQPWRG4Q1 is appropriate for body and chassis control electronics where one package must provide multiple general-purpose analog channels. A quad amplifier can support actuator command conditioning, position-sensor interfaces, switch-state amplification, and diagnostic signal paths without using four separate packages. Its automotive-family identity and 26 V maximum supply rating make it relevant to 12 V and 24 V vehicle electrical architectures, although surge and load-dump protection must be handled by the surrounding power network. The 1.2 MHz gain-bandwidth product supports low-frequency control loops, and the 2 mV input offset provides a defined starting point for closed-loop error analysis.
پێشنیارکراو
Battery-Powered Sensor Interfaces
The LM2902KVQPWRG4Q1 can serve as the analog front end for battery-powered pressure, temperature, position, or current sensors in vehicle systems. Four channels allow designers to combine non-inverting gain, inverting gain, active filtering, and reference buffering on one board. The device's 26 V supply capability provides headroom in automotive electrical environments, while its 1.2 MHz gain-bandwidth product is adequate for many sensor bandwidths below 100 kHz. The 2 mV input offset specification should be included in total error calculations, together with input bias current, resistor tolerance, and common-mode limitations. Supply bypassing and input routing are particularly important because long harness-connected sensor nodes can couple noise into high-impedance amplifier inputs.
پێشنیارکراو
Transducer Bridge Excitation and Readback
The LM2902KVQPWRG4Q1 can support bridge-style sensor interfaces when the excitation and readback network must remain within the amplifier's input common-mode and output-swing limits. One channel can buffer an excitation source, another can amplify the differential sensor output, and the remaining channels can provide gain or active filtering. Its 1.2 MHz gain-bandwidth product allows useful bandwidth for common resistive-bridge and strain-gauge measurement systems, but it does not make the device a high-speed instrumentation amplifier. The 2 mV input offset can contribute directly to the measured bridge imbalance, so design calculations should include offset drift, bias-current effects, resistor matching, and the sensor's intrinsic sensitivity.
پێشنیارکراو
Actuator Drive Signal Conditioning
The LM2902KVQPWRG4Q1 is useful for conditioning low-current actuator commands in vehicle electronic modules. It can amplify a controller output, level-shift it into an acceptable control range, buffer a feedback signal, or provide active filtering before a discrete transistor or driver stage. The amplifier's 26 V maximum supply rating supports automotive supply environments, while the 1.2 MHz gain-bandwidth product is more than adequate for slow solenoid, valve, or motor-control envelopes. Output-current capability, output swing, and capacitive-load stability must be checked against the actuator-driver interface. Protection or a separate driver stage is required when the load current exceeds the operational-amplifier output capability.
پێشنیارکراو
General-Purpose Industrial Control Amplification
The LM2902KVQPWRG4Q1 can also serve in industrial control boards that use an automotive-qualified quad amplifier for signal conditioning. Four channels can handle analog inputs, loop error signals, reference buffering, and output conditioning within one package. The 1.2 MHz gain-bandwidth product is suitable for common process-control bandwidths, and the 2 mV offset provides a useful specification for amplifier error analysis. Industrial designs must observe the 26 V maximum supply rating and provide input protection for transients above that limit. Stable feedback components, short traces, local supply decoupling, and adequate output-load analysis are required to obtain predictable operation across temperature and process variations.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2902KVQPWRG4Q1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2902QPWRG4Q1 | LM2902KVQPWRQ1 | LM2902PT | LM2902KVPT |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin TSSOP (PW) | 14-pin TSSOP (PW) | 14-pin TSSOP (PW) | 14-pin TSSOP (PT) | 14-pin TSSOP (PT) |
| Amplifier Configuration | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Automotive Family | LM2902-Q1 automotive family | LM2902 family | LM2902-Q1 automotive family | LM2902 family | LM2902-Q1 automotive family |
| Ordering Suffix | KVQPWRG4Q1 | QPWRG4Q1 | KVQPWRQ1 | PT | KVPT |
جیاکەرەوە سەرەکییەکان
- Exact automotive-family orderable code (بەراورد بەLM2902QPWRG4Q1)
- Four-channel integration in a 14-pin TSSOP (بەراورد بەLM2902PT)
- Automotive KV family with the target order suffix (بەراورد بەLM2902KVPT)
- Close family retention of electrical behavior (بەراورد بەLM2902KVQPWRQ1)
تێبینییەکانی دیزاین
Route each amplifier's input and feedback components close to their corresponding pins, and place supply bypass capacitors immediately between the supply and ground pins. Keep sensitive sensor inputs away from actuator-control traces and switching nodes. The quad layout can create accidental coupling between channels, so preserve separation between adjacent amplifier sections and ground return currents. Because this is a 14-pin TSSOP device, inspect the manufacturer pin configuration and exposed copper geometry before finalizing the land pattern.
Do not assume that the 26 V maximum supply rating permits unrestricted operation near that limit. Confirm the transient profile, automotive supply conditions, input common-mode range, output swing, and load current at every operating condition. The 2 mV input offset can be significant in high-gain sensor measurements, so include it in the error budget along with bias current and drift. The part is no longer in production, making traceability and last-time-buy planning more important than nominal pin compatibility.
Use the TSSOP land pattern with continuous copper beneath and around the device where the package and board construction permit, and avoid placing it beside a heat source without thermal analysis. Operational-amplifier dissipation depends on the supply voltage, output voltage, load current, and ambient temperature. Confirm that the worst-case internal dissipation keeps the junction below its rating. For high-current or sustained-output operation, add an external buffer rather than forcing current through the amplifier output.
زانیاری پابەندبوون
Texas Instruments identifies the LM2902-Q1 as an automotive family. Detailed RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements for the exact orderable code are not listed in the product information used for this summary.