Texas Instruments

LM2903AVQDRG4 - Dual Comparator for Analog Control | TI

MPN: LM2903AVQDRG4 ✓ چالاک
2 V to 36 V Vdss 8-SOIC, 0.154 in width and 3.90 mm width Package
MOQ: 1 |

LM2903AVQDRG4 گشتی

The Texas Instruments LM2903AVQDRG4 is a dual differential analog comparator with two independent comparison channels, a 2 V to 36 V supply range, and an 8-pin SOIC package. It provides open-collector outputs, 2 mV typical input offset voltage, and a 0.3 µs response time for general-purpose signal detection and control applications.

An analog comparator is a semiconductor IC that compares two input voltages and changes its output state when one input crosses the other. The LM2903 family belongs to the comparator hierarchy, where a comparator is an amplifier-class interface IC used for thresholding, sensing, level translation, and system protection. Its two channels can operate independently, allowing one package to implement two comparison functions.

The principal electrical features are the 2 V to 36 V single-supply operating range, 2 mV typical offset voltage, and 0.3 µs response time. Single or dual supplies are supported, while the open-collector output stage requires an external pull-up resistor to establish a valid logic-high voltage. The V-grade designation identifies the low-supply-current version of the LM2903 family.

Internally, each channel includes a differential input stage, a bias network, and an open-collector output stage. The two comparators share common supply and ground pins but retain separate non-inverting, inverting, and output connections. This arrangement supports independent sensing tasks while reducing package count compared with two single-channel comparator ICs.

Typical uses include overvoltage and undervoltage detection, battery monitoring, sensor thresholding, temperature-control loops, industrial control signals, and digital system conditioning. The wide supply range is useful in equipment operating from regulated low-voltage rails as well as industrial systems with higher supply voltages. The open-collector output also permits wired signal combining when the system uses compatible pull-up rails and logic levels.

For reliable operation, select pull-up resistors appropriate for the output logic voltage and account for the open-collector sink-current limit. Input common-mode range, output saturation behavior, and supply bypass requirements must be checked against the operating conditions. Decoupling capacitors should be placed close to the supply and ground pins to limit coupling from adjacent switching circuitry.

This page organizes the LM2903AVQDRG4 specifications, practical application guidance, and verified drop-in alternatives into one engineering reference. It also highlights the distinctions among automotive, B-revision, and comparator-family alternatives so that a replacement can be selected by package, pinout, voltage envelope, and intended application rather than by package name alone.

جێگرەوەکانی جێگۆڕکێ بۆ LM2903AVQDRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903AVQDRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Comparator Type, Operating Temperature Range, Response Time, Output Type.

Texas Instruments
Package: 8-SOIC (D), 3.90 mm body width
Comparator Type: Differential
Operating Temperature Range: -40 °C to +125 °C
بەراوردکردن لەگەڵ LM2903AVQDRG4 →
Texas Instruments
Package: 8-SOIC (D), 0.154 in (3.90 mm) body width
Comparator Type: Differential, general purpose
Operating Temperature Range: -40 C to +125 C
بەراوردکردن لەگەڵ LM2903AVQDRG4 →
Texas Instruments
Package: 8-pin SOIC (D)
Operating Temperature Range: -40 °C to +125 °C
بەراوردکردن لەگەڵ LM2903AVQDRG4 →
Texas Instruments
Package: 8-pin SOIC
Operating Temperature Range: -40 °C to +125 °C
Response Time: 300 ns
بەراوردکردن لەگەڵ LM2903AVQDRG4 →
Texas Instruments
Package: 8-pin SOIC (D)
Comparator Type: Dual differential general-purpose comparator
Operating Temperature Range: -40°C to +85°C
بەراوردکردن لەگەڵ LM2903AVQDRG4 →
Texas Instruments
Package: SOIC-8 (D), 3.90 mm body width
Operating Temperature Range: 0 °C to +70 °C
Response Time: 1.3 µs (typical)
بەراوردکردن لەگەڵ LM2903AVQDRG4 →

LM2903AVQDRQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-SOIC
Differential, general purpose · 2 · Open-Collector / Open-Drain, Rail-to-Rail · 2 V to 36 V · +/-1 V to +/-18 V · Rail-to-Rail · 0.4 mA per channel (distributor specification listing) · 1.3 us

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903BIDR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-SOIC
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393BIDR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-SOIC
Dual differential general-purpose comparator · 2 channels · Open-collector · 38 V · -38 V to +38 V · Includes ground · 2.5 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903DR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-SOIC
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393DR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-SOIC
Texas Instruments · LM393DR · Dual Differential Comparator · 2 · Open-Collector · 2 V to 36 V · ±1 V to ±18 V · 1 mV

✓ بەردەستە

$0.11 / یەکە

بینینی داتاشیت →

LM2903AVQDRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Comparator Type Dual differential comparator
Number of Channels 2 channels
Supply Voltage Range 2 V to 36 V
Dual-Supply Operating Range ±1 V to ±18 V
Input Offset Voltage 2 mV typical
Response Time 0.3 µs
جۆری دەرچوون Open-collector
پاکێج 8-SOIC, 0.154 in width and 3.90 mm width
جۆری دامەزراندن Surface mount
Automotive Qualification AEC-Q100 automotive catalog variant

ڕێکخستنی پینی LM2903AVQDRG4

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT1 — Comparator 1 open-collector output
پین 2 IN-1 — Comparator 1 inverting input
پین 3 IN+1 — Comparator 1 non-inverting input
پین 4 GND — Ground connection
پین 5 IN+2 — Comparator 2 non-inverting input
پین 6 IN-2 — Comparator 2 inverting input
پین 7 OUT2 — Comparator 2 open-collector output
پین 8 VCC — Positive supply connection

بەکارهێنانە باوەکان

LM2903AVQDRG4 گونجاوە بۆ 6 بەکارھێنانs: Battery Voltage Monitoring, Overvoltage and Undervoltage Protection, Industrial Sensor Thresholding, Temperature Control Loops, Digital Logic Level Conditioning, Power-Supply Fault Signaling.

⚡

Battery Voltage Monitoring

The LM2903AVQDRG4 fits battery threshold detection because its two independent channels can monitor positive and negative transitions against reference voltages. The 2 V to 36 V supply range supports many battery-powered systems, while 2 mV typical input offset voltage helps place a switching threshold close to the intended cell voltage. Connect the battery voltage to a non-inverting input and a divided reference to the inverting input, then use the open-collector output to drive a warning or shutdown signal. An external pull-up sets the logic-high voltage and must be selected for the receiving logic. Check the input common-mode range over the complete battery discharge and charging profile so both the comparator input and supply remain within their operating limits.

🏭

Overvoltage and Undervoltage Protection

The LM2903AVQDRG4 can implement two independent supply-limit checks in an industrial or automotive control module. One channel compares a feedback voltage with an upper threshold, while the other checks a lower threshold, allowing the open-collector outputs to combine into a fault signal. Its 0.3 µs response time supports rapid detection, and the 2 V to 36 V operating range accommodates a broad range of protected rails. Divide the monitored voltage down before applying it to the inputs so the signal stays within the common-mode limits. Use appropriately rated feedback resistors and pull-up resistors, and account for output sinking current when several protection signals share a wired bus.

🧩

Industrial Sensor Thresholding

The LM2903AVQDRG4 is appropriate for converting a continuously variable sensor signal into a digital limit state. A resistive divider can scale the sensor voltage into the comparator input range, while one channel monitors the upper threshold and the other the lower threshold. The 2 mV typical input offset voltage supports threshold accuracy when the sensing system does not require millivolt-level resolution across a wide temperature range. Because the outputs are open collector, each channel can drive an optocoupler, relay-control input, or digital isolator after adding a suitable pull-up resistor. Keep high-impedance sensor nodes short and place the divider close to the comparator when noise or leakage could otherwise shift the crossing point.

♨️

Temperature Control Loops

The LM2903AVQDRG4 can serve as the switching element in a simple thermistor-based temperature controller. One channel compares the divided thermistor voltage with a setpoint generated by another divider, while its open-collector output controls a heater, fan, or relay-driver stage. The dual-channel configuration can support two temperature thresholds, such as control and alarm points. Its 0.3 µs response time helps limit delay around the switching threshold, and the 2 V to 36 V supply range allows operation from several common industrial rails. Select resistor values that keep the divider current above leakage effects, and size the pull-up resistor for the required output transition speed and sink current.

🔧

Digital Logic Level Conditioning

The LM2903AVQDRG4 is useful when a sensor or legacy logic signal must be translated into a clean open-collector event. The differential inputs compare the incoming level against a local reference, and the output changes state only after the threshold is crossed. Pull-up the output to the destination logic rail so the translated voltage remains compatible with the receiving circuit. This avoids tying the comparator output to a fixed supply when the source and destination use different voltage domains. The 2 mV typical offset and 0.3 µs response time support dependable digital decision-making, but the source signal must remain inside the comparator's input common-mode range. Add hysteresis with positive feedback when chatter around the threshold could repeatedly toggle the output.

🖥️

Power-Supply Fault Signaling

The LM2903AVQDRG4 can monitor a power rail and generate an open-collector fault indication for a controller, sequencer, or system supervisor. One channel detects excessive rail voltage, while the other identifies a rail below its valid operating threshold. Its wide 2 V to 36 V supply range supports operation in both low-voltage electronics and higher-voltage industrial systems. The open-collector outputs can be wired together when the logic system requires a single active-low fault line, provided the total sink current remains within the device limit. Use a resistor divider to create the monitored signal, verify operation at startup and shutdown, and choose a pull-up voltage that remains compatible with every connected receiver.

What is the operating voltage of LM2903AVQDRG4?
The LM2903AVQDRG4 operates from 2 V to 36 V with a single supply or from ±1 V to ±18 V with dual supplies. According to the Texas Instruments LM2903 datasheet, each of the two channels can operate from the same supply arrangement, although common-mode and output limits must be considered for a particular design.
What are the key specifications of LM2903AVQDRG4 that engineers should know?
The LM2903AVQDRG4 provides two independent differential comparator channels, a 2 V to 36 V supply range, 2 mV typical input offset voltage, 0.3 µs response time, and open-collector outputs in an 8-SOIC package. Texas Instruments identifies it as a general-purpose dual comparator with low-supply-current V-grade characteristics.
Where can I download the LM2903AVQDRG4 datasheet PDF?
The authoritative LM2903AVQDRG4 documentation is available from the Texas Instruments LM2903 product page. The datasheet contains the ordering table, absolute maximum ratings, electrical characteristics, pin configuration, typical application information, and device-replacement guidance needed to confirm an exact ordering code.
Where is the LM2903AVQDRG4 pinout?
The LM2903AVQDRG4 pinout is shown in the pin-configuration section of the Texas Instruments LM2903 datasheet. Pin 1 is OUT1, pins 2 and 3 are IN−1 and IN+1, pin 4 is GND, pins 5 and 6 are IN+2 and IN−2, pin 7 is OUT2, and pin 8 is VCC.
Can the LM2903AVQDRG4 operate from dual supplies?
Yes, the LM2903AVQDRG4 can operate from dual supplies within the specified ±1 V to ±18 V range. The two comparator channels are independent at their input and output pins but share the supply pins. Check the datasheet's common-mode input and output saturation limits before operating near either supply rail.
Why does the LM2903AVQDRG4 open-collector output need a pull-up resistor?
The LM2903AVQDRG4 output can sink current but cannot actively drive its output high, so an external pull-up resistor is required. According to the Texas Instruments LM2903 datasheet, this arrangement supports open-drain-style wired logic and allows the pull-up voltage to match the receiving circuit's logic level.
Where to buy LM2903AVQDRG4 online?
The LM2903AVQDRG4 can be requested through the Request a Quote form on this page. Submit the exact MPN, target quantity, delivery location, and required packaging so the order can be matched to the correct Texas Instruments ordering code without ambiguity.
What is the price of LM2903AVQDRG4?
Current commercial terms for the LM2903AVQDRG4 are provided through the Request a Quote form on this page. The form accepts the exact MPN, quantity, and shipment requirements, allowing the current order configuration to be reviewed without publishing a potentially stale price.
What is the lead time for LM2903AVQDRG4?
The current lead time for the LM2903AVQDRG4 should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, manufacturing allocation, package configuration, and shipment destination, so it is best to request the schedule together with the exact ordering information.
Is LM2903AVQDRG4 in stock?
Current inventory status for the LM2903AVQDRG4 should be checked through the Request a Quote form on this page. Provide the required quantity and delivery destination so the latest stock and order-confirmation status can be addressed for the exact ordering code.
What can replace LM2903AVQDRG4?
The LM2903AVQDRG4 can be replaced by a pin-compatible 8-SOIC LM2903-family device when its supply range, channel configuration, input limits, output behavior, qualification, and temperature requirements match. LM2903AVQDRQ1 is an automotive-catalog option, while LM2903BIDR and LM393BIDR are documented B-revision-family candidates.
Is LM2903AVQDRG4 the same as LM2903AVQDRQ1?
Yes, LM2903AVQDRQ1 is closely related to the LM2903AVQDRG4 and uses the same 8-SOIC dual-comparator configuration. The Q1 ordering code denotes an automotive-catalog variant, so it is the preferred candidate when automotive qualification is required; confirm the temperature and qualification details against the intended design.
LM2903AVQDRG4 vs LM2903BIDR - which is better for an industrial control board?
LM2903BIDR is the better candidate when a documented B-revision device with the same 8-SOIC envelope is required, while LM2903AVQDRG4 is appropriate for a design specifying the V-grade low-supply-current ordering path. Both retain two channels, a 2 V to 36 V supply framework, and SOIC-8 packaging, but qualification and ordering requirements should decide the choice.
When should I choose LM2903AVQDRG4 over LM2903AVQDRQ1?
Choose LM2903AVQDRG4 when the board does not require the automotive-catalog Q1 ordering path and the V-grade low-supply-current feature is desirable. Choose LM2903AVQDRQ1 when automotive qualification is part of the system requirement. Both use an 8-SOIC package, so the mechanical footprint remains compatible.
Is LM2903AVQDRG4 suitable for battery and power-supply monitoring?
The LM2903AVQDRG4 is suitable for battery and power-supply monitoring when the monitored voltage, common-mode range, and output pull-up arrangement meet its limits. Its 2 V to 36 V supply range and 2 mV typical offset voltage support threshold detection, while the open-collector output can drive a digital input or protection signal.
What is the best cross-brand equivalent for LM2903AVQDRG4?
A cross-brand equivalent should be selected only after its manufacturer confirms an 8-SOIC pin-for-pin footprint, two-channel open-collector output, compatible supply range, and suitable common-mode limits. Use the Request a Quote form on this page with the target application and required qualification criteria so a candidate can be evaluated against the exact LM2903AVQDRG4 operating conditions.

داتای سەرچاوەی ئەندازیاری بۆ LM2903AVQDRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM2903AVQDRG4 for a general-purpose dual-comparator design that specifies the V-grade low-supply-current device and an 8-SOIC footprint. LM2903AVQDRQ1 is the closest choice when the automotive-catalog Q1 ordering path is required. LM2903BIDR is appropriate when the board is assigned a B-revision LM2903 device and its electrical limits have been checked. LM393BIDR or LM393DR should be selected only after confirming output and common-mode characteristics because they belong to the LM393 family rather than the LM2903 family. For every alternative, verify the complete pinout, supply range, input voltage limits, output sink current, qualification, and temperature grade against the original design before production release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2903AVQDRQ1 LM2903BIDR LM393BIDR LM2903DR LM393DR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Comparator Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector

جیاکەرەوە سەرەکییەکان

  • Two-channel comparison in one 8-SOIC package (بەراورد بەLM2903DR)
  • Automotive-catalog ordering option (بەراورد بەLM2903BIDR)
  • Fast 0.3 µs response with 2 mV typical offset (بەراورد بەLM393BIDR)

تێبینییەکانی دیزاین

Place the input divider networks close to pins 2, 3, 5, and 6 to minimize pickup from adjacent switching nodes. Route the two output nets separately because each open-collector output requires its own pull-up resistor. Keep the pin 8 supply trace short, connect a decoupling capacitor directly to pin 8 and pin 4, and provide a quiet ground return to avoid introducing supply noise into the threshold decision.

Add deliberate hysteresis with positive feedback when the input can cross the threshold slowly or with noise. The resistor values must preserve the intended switching point because leakage and input offset voltage shift the effective crossing voltage. Also verify that the source impedance stays low enough for the comparator input current and that the selected pull-up value satisfies both the required logic-high voltage and output sink-current limit.

Do not treat the open-collector output as a push-pull logic output; without a pull-up resistor, OUT1 and OUT2 cannot establish a valid logic-high state. Check input common-mode limits during power-up and shutdown, especially when the monitored signal can lead the supply. For wired fault outputs, calculate the sum of all pull-up currents and confirm that the combined sink current does not exceed the device limit.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The Q1 ordering code is identified as an automotive-catalog variant. Other environmental and material compliance declarations require confirmation from the manufacturer for the exact ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2903AVQDRG4 LM2903AVQDRG4 datasheet LM2903AVQDRG4 datasheet pdf LM2903AVQDRG4 pinout Texas Instruments LM2903AVQDRG4 LM2903AVQDRG4 8-SOIC LM2903AVQDRG4 2V 36V LM2903AVQDRG4 open collector LM2903AVQDRG4 equivalent LM2903AVQDRG4 replacement LM2903AVQDRG4 vs LM2903AVQDRQ1 LM2903AVQDRG4 price LM2903AVQDRG4 stock LM2903AVQDRG4 battery monitoring LM2903AVQDRG4 overvoltage protection

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM2903AVQDRG4 LM2903AVQDRQ1 LM2903BIDR LM393BIDR LM2903DR LM393DR dual differential comparator analog comparator amplifier IC interface IC semiconductor open-collector output open-drain logic PSRR 8-SOIC SOIC package family surface-mount package SMD input offset voltage response time battery monitoring overvoltage protection industrial sensor thresholding temperature control
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ