LM2903AVQDRQ1 - 36V AEC-Q100 Dual Open-Collector Comparator | Texas Instruments
MPN: LM2903AVQDRQ1 ✓ چالاکLM2903AVQDRQ1 گشتی
A comparator is a type of analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. Because a comparator only switches when its inputs cross, it is used as a threshold detector rather than as an amplifier, sitting in the signal chain between a sensor or divider network and the logic block that reacts to the decision. In the wider hierarchy, a comparator belongs to the amplifier and comparator IC family within the broader category of analog and mixed-signal integrated circuits.
Key features of this device include two independent comparison channels, rail-to-rail input common-mode operation, an open-collector output stage that can sink up to 16 mA and drive external relays or TTL loads, low supply current that stays essentially independent of supply voltage, and a 1.3 µs propagation delay. The open-collector architecture allows several comparators to be wire-ORed together on a shared bus, and the output can be pulled up to any logic level the system uses.
Internally the device is built around a differential input stage, a second stage, and a bipolar open-collector output driver, which is why the supply current draw is described as independent of supply voltage. The wide 36 V total supply capability is what allows the same part to sit directly on 12 V and 24 V automotive and industrial rails without external protection, and the low offset and low bias currents keep the threshold error small compared with the resistive dividers usually placed in front of it.
Typical applications include automotive battery and 12 V rail monitoring, industrial sensor threshold conditioning, overvoltage and undervoltage protection in power supplies, motor drive current-limit and stall detection, medical instrumentation window comparison, and IoT sensor-level detection. The AEC-Q100 Grade 0 and Grade 1 qualification supports use in harsh automotive environments where temperature extremes and ESD events are common.
When designing with this part, remember that the open-collector output needs an external pull-up resistor, and that a device driving a large relay or solenoid coil needs a flyback diode to protect the output transistor from inductive voltage spikes. Keep the input divider resistors close to the pins to limit parasitic pickup on high-impedance threshold networks.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903AVQDRQ1 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903AVQDRQ1 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Output Type, Package, Comparator Type, Propagation Delay, Automotive Qualification.
LM2903AVQDRG4Q1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903AVQDRG4Q1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903QDRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903HYDT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM393AMX
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903AVQDRQ1 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Differential, general purpose |
| Number of Channels | 2 |
| جۆری دەرچوون | Open-Collector / Open-Drain, Rail-to-Rail |
| Supply Voltage Range, Single | 2 V to 36 V |
| Supply Voltage Range, Dual | +/-1 V to +/-18 V |
| Input Common-Mode Range | Rail-to-Rail |
| ئێستای دابینکردن | 0.4 mA per channel (distributor specification listing) |
| Propagation Delay | 1.3 us |
| مەودای پلەی گەرمیی کارکردن | -40 C to +125 C |
| Automotive Qualification | AEC-Q100 Grade 0 and Grade 1 |
| ESD Qualification Test | MIL-STD-883, Method 3015 |
| پاکێج | 8-SOIC (D), 0.154 in (3.90 mm) body width |
| ژمارەی پینەکان | 8 |
| جۆری دامەزراندن | Surface Mount |
| Supply Voltage Independent Supply Current | Yes, low supply-current drain independent of supply voltage |
ڕێکخستنی پینی LM2903AVQDRQ1
| پین 1 | OUT1 — Open-collector output of comparator 1 |
| پین 2 | IN1- — Inverting input of comparator 1 |
| پین 3 | IN1+ — Non-inverting input of comparator 1 |
| پین 4 | V- — Negative supply or ground reference |
| پین 5 | IN2+ — Non-inverting input of comparator 2 |
| پین 6 | IN2- — Inverting input of comparator 2 |
| پین 7 | OUT2 — Open-collector output of comparator 2 |
| پین 8 | V+ — Positive supply input |
بەکارهێنانە باوەکان
LM2903AVQDRQ1 گونجاوە بۆ 6 بەکارھێنانs: Automotive Battery and 12 V Rail Monitoring, Industrial Sensor Threshold Conditioning, Power Supply Overvoltage and Undervoltage Protection, Motor Drive Current-Limit and Stall Detection, Medical Instrumentation Threshold Monitoring, IoT and Smart Sensor Level Detection.
Automotive Battery and 12 V Rail Monitoring
The LM2903AVQDRQ1 fits 12 V and 24 V vehicle rails because it accepts a single supply of 2 V to 36 V with rail-to-rail inputs, so a resistor divider from the battery to ground can be compared against a 1.2 V bandgap-style reference without level shifting. The AEC-Q100 Grade 0 and Grade 1 qualification and the -40 C to +125 C rating cover underhood and body-module environments where temperature extremes and load dump transients are routine. Two independent open-collector channels allow one comparator to watch a high threshold and the other a low threshold, with both outputs pulled up to the module logic level. Because supply current is independent of supply voltage, the quiescent draw stays near 0.4 mA per channel whether the module runs at 8 V or 36 V, which matters for vehicles that spend time on a partially depleted battery.
پێشنیارکراو
Industrial Sensor Threshold Conditioning
The LM2903AVQDRQ1 turns analog sensor nodes into clean logic events in industrial instrumentation. A thermistor, RTD or resistive bridge output is scaled by a divider and compared against a setpoint on one input while the other input holds the reference, and the open-collector output directly drives a PLC input, a relay driver or an opto-isolator input through a pull-up resistor. The 1.3 us propagation delay is negligible compared with the thermal and mechanical time constants of the sensed process, so false switching is not a concern. Its 36 V supply capability allows the comparator to sit on a 24 V control rail and share that rail with the sensor conditioning circuitry, which simplifies the power tree. The -40 C to +125 C rating covers unheated enclosures, cabinets and field boxes that would push an industrial-temperature part past its limits.
پێشنیارکراو
Power Supply Overvoltage and Undervoltage Protection
The LM2903AVQDRQ1 implements hardware overvoltage and undervoltage cutoffs around a DC-DC or AC-DC converter without relying on firmware. A tap from the output rail is scaled by a resistor divider, compared against a precision reference on the opposite input, and the open-collector output pulls a crowbar or series disconnect MOSFET gate low to remove the faulted rail. Because the open-collector stage can sink up to 16 mA, it can drive a gate resistor network or a fault latch directly, and the output can be wire-ORed with a second comparator so that either fault condition disables the supply. Its wide 2 V to 36 V supply range means the protection circuit can be powered from the same wide input bus it is protecting, and the low supply-current drain keeps the protection path from disturbing the power budget of a low-power system.
پێشنیارکراو
Motor Drive Current-Limit and Stall Detection
The LM2903AVQDRQ1 serves as the hardware trip detector behind the current-sense amplifier in a brushless DC or stepper motor driver. The amplified shunt voltage representing motor current is compared against a programmed limit, and when the threshold is crossed the open-collector output asserts a fault signal that inhibits the gate drivers, protecting the MOSFETs and the motor windings from a stalled rotor or a shorted phase. The 1.3 us response time is fast enough to react to a step change in current before the switching devices exceed their pulsed current rating. Because the output is open-collector, the fault line can be shared between the two comparators of the pair, one watching phase A and one watching phase B, and can also feed a microcontroller interrupt without level translation.
پێشنیارکراو
Medical Instrumentation Threshold Monitoring
The LM2903AVQDRQ1 can be used in diagnostic and monitoring equipment as a hardware guard on a patient-sensing front end. A buffered electrode or sensor signal is compared against a configured threshold, and the open-collector output disables an alarm path or a stimulation output when the signal leaves the valid window, adding a deterministic hardware interlock alongside the software checks. Rail-to-rail input operation means the sensing chain can operate from a single low-voltage rail without headroom concerns on the threshold inputs, and the wide supply range allows the interlock to be powered from the same auxiliary rail as the analog front end. The low supply-current drain and the wide -40 C to +125 C rating suit both bedside monitors and compact portable carts where enclosure space and thermal budget are constrained.
پێشنیارکراو
IoT and Smart Sensor Level Detection
The LM2903AVQDRQ1 gives always-on wireless sensor nodes a hardware event trigger instead of a software polling loop. A resistive divider from a battery, thermistor or capacitive sensor is compared against a reference and the open-collector output wakes the radio MCU through an interrupt pin, so the node sleeps between events and only powers up when a threshold is crossed. The 2 V minimum supply lets the part run directly from a single lithium cell or a 3.3 V rail, while the 36 V maximum provides surge headroom when the module is connected to longer field wiring. Two channels in one 8-SOIC package let a node watch two thresholds, for example a high-water and a low-water level, at a lower footprint cost than two discrete comparators, and the open-collector outputs can be wired together onto a single wake line.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2903AVQDRQ1 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903AVQDR | LM2903AVQDRG4 | LM2903D | LM2903QDR | LM2903HYDT | LM393AMX |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | onsemi |
| Package | 8-SOIC (D) | 8-SOIC (D) - same | 8-SOIC (D) - same | 8-SOIC (D) - same | 8-SOIC (D) - same | 8-SOIC (D) - same | 8-SOIC (D) - same |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-Collector / Open-Drain, Rail-to-Rail | Open-Collector | Open-Collector | Open-Collector | Open-Collector | Open-Collector | Open-Collector |
| Automotive Qualification (AEC-Q100) | Grade 0 and Grade 1 | Not qualified | Not qualified | Not qualified | Not qualified | Not qualified | Not qualified |
| Number of Pins | 8 | 8 | 8 | 8 | 8 | 8 | 8 |
جیاکەرەوە سەرەکییەکان
- Automotive qualification with 36 V supply headroom in the same 8-SOIC footprint (بەراورد بەLM2903AVQDR)
- Qualification gap closes for vehicle and heavy-transport designs (بەراورد بەLM2903HYDT)
- Two threshold channels in one 8-pin package (بەراورد بەLM393AMX)
- Supply current independent of supply voltage (بەراورد بەLM2903D)
تێبینییەکانی دیزاین
The open-collector output is not a push-pull logic output and must have an external pull-up resistor, typically 10 kOhm to the local logic rail, or the output will float and never present a valid high level. Because the output is open collector, several comparators can be wire-ORed onto one bus line, which is a deliberate feature for window detection. Never assume the output can source current; it only sinks, and the pull-up determines the rise time.
Keep the input divider resistors and any reference capacitor physically close to pins 2, 3, 5 and 6 to minimize parasitic pickup on high-impedance threshold networks. Decouple the supply at pin 8 with a 100 nF ceramic capacitor placed at the pin and add 1 uF to 10 uF of bulk capacitance close to the device if the supply wiring is long. Keep the analog input traces away from relay coil and motor phase traces, because the 1.3 us response time means fast switching edges on adjacent nets can couple into the threshold node and cause false triggers.
Estimated: with a 12 V supply, a 5 V threshold network and a 16 mA maximum output sink into a relay coil, the output transistor dissipates roughly (12 V - 3.3 V) x 16 mA = about 0.14 W while the coil is energized, and the coil itself may draw 100 mA or more from the 12 V rail. Estimated: at a 36 V maximum supply this rises to about (36 V - 3.3 V) x 16 mA = 0.52 W. Keep the relay or load current within the output sink rating and add a flyback diode across any inductive load to keep the output transistor out of avalanche when the coil is switched off.
The LM2903AVQDRQ1 dissipates very little internally in normal threshold-detection service because the quiescent current stays near 0.4 mA per channel regardless of supply voltage, and the output stage only conducts while the output transistor is on. Estimated: at a 36 V supply with both channels sinking 16 mA continuously, total dissipation is roughly 1.0 W, which is manageable in an 8-SOIC on a standard copper pour. Provide at least a modest ground-plane area under the package so the thermal pad of the SOIC can spread heat into the board.
Do not apply a differential input voltage beyond the absolute maximum rating between pins 2 and 3 or between pins 5 and 6, even momentarily, because the input stage can be damaged before the output clamps. In battery monitoring circuits where a reverse connection is possible, protect the inputs with series resistors and a clamp structure. Also remember that the Q1 suffix denotes AEC-Q100 Grade 0 and Grade 1 qualification, not a different pinout, so the footprint is unchanged between the Q1 and standard variants.
زانیاری پابەندبوون
Texas Instruments lists the LM2903AVQDRQ1 as AEC-Q100 Grade 0 and Grade 1 qualified for automotive applications, tested to MIL-STD-883 Method 3015. RoHS, REACH, lead-free and halogen-free statements are [DATA_NEEDED] and are not asserted here without a manufacturer statement.