LM2903EDR2G - Dual 36V Low Offset Comparator | onsemi | SOIC-8
MPN: LM2903EDR2G ✓ چالاکLM2903EDR2G گشتی
A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC family - related to operational amplifiers but optimized for fast, saturated switching rather than linear amplification - and are fundamental elements of power management, signal conditioning, and mixed-signal systems. Dual comparators such as the LM2903 family integrate two independent comparator cells in one package, halving board area versus two single-channel parts.
Key features of the LM2903EDR2G include single-supply operation from roughly 2 V up to 36 V, a common-mode input range that extends down to ground level (negative rail), and an open-collector output that allows wire-OR connection of multiple comparators and simple interfacing to logic levels up to the supply rail through an external pull-up resistor. The low 2.0 mV input offset voltage specification permits accurate threshold detection with modest hysteresis network design.
Technically, the device uses a differential PNP input stage, which is what allows the input common-mode range to reach ground even when powered from a single positive supply. The output transistor sinks current to ground while the pull-up resistor defines the logic-high level, making the part level-flexible across 5 V, 12 V, 24 V, and 36 V industrial rails.
Typical applications include overvoltage and undervoltage monitoring, limit comparators in power supplies, window detectors, square-wave and relaxation oscillators, and analog-to-digital threshold interfacing in industrial automation equipment.
A key design consideration: because the open-collector output only sinks current, every output requires a pull-up resistor, and response time depends strongly on the chosen pull-up value - lighter pull-ups trade speed for lower power.
This page synthesizes distributor availability data, pin-compatible drop-in alternatives, and practical design notes in one place - information not consolidated in the manufacturer datasheet alone.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903EDR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903EDR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Comparator Type, Channel Independence, Operating Temperature Range, Propagation Delay.
LM2903DR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903VDR2
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM393DR2G
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903M/NOPB
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903EDR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| کارکردن | Dual independent precision voltage comparator |
| Number of Channels | 2 |
| Supply Voltage (Maximum) | 36 V |
| Split Supply (Maximum) | ±18 V |
| Input Offset Voltage | 2.0 mV (as low as, per manufacturer datasheet) |
| جۆری دەرچوون | Open-collector |
| Input Common-Mode Range | Includes ground (negative rail) |
| Supply Operation | Single or split supply |
| پاکێج | 8-SOIC (SO-8, surface mount) |
| جۆری دامەزراندن | Surface Mount |
| Packing | Tape and Reel (R2 suffix) |
| پۆل | Standard general-purpose comparator |
ڕێکخستنی پینی LM2903EDR2G
| پین 1 | OUT A — Comparator A output (open collector) |
| پین 2 | INA- — Comparator A inverting input |
| پین 3 | INA+ — Comparator A non-inverting input |
| پین 4 | GND (V-) — Ground / negative supply |
| پین 5 | INB+ — Comparator B non-inverting input |
| پین 6 | INB- — Comparator B inverting input |
| پین 7 | OUT B — Comparator B output (open collector) |
| پین 8 | VCC (V+) — Positive supply, up to 36 V |
بەکارهێنانە باوەکان
LM2903EDR2G گونجاوە بۆ 6 بەکارھێنانs: Overvoltage / Undervoltage Monitoring, Industrial Automation Threshold Detection, Square-Wave and Relaxation Oscillators, Power Supply Control and Protection, Battery-Powered and Portable Equipment, Analog-to-Digital Threshold Interfacing.
Overvoltage / Undervoltage Monitoring
The LM2903EDR2G is a natural fit for supply-rail supervision because its 36 V maximum rating covers 12 V automotive and 24 V industrial buses directly, and its common-mode input range reaching ground allows sensing of near-zero fault conditions without negative bias. Each of the two independent comparator channels can implement one threshold, so a single package provides both overvoltage and undervoltage detection for a window-monitor function. The open-collector outputs wire-OR together so that either fault condition pulls a shared alarm line low. With the 2.0 mV-class offset, threshold accuracy is dominated by the resistor divider tolerance rather than the comparator, enabling ±1-2% trip-point accuracy with 1% resistors and modest hysteresis of 10-50 mV to prevent chatter near the threshold.
پێشنیارکراو
Industrial Automation Threshold Detection
In factory automation, sensor signals such as 4-20 mA loops converted to voltage, limit switches with analog conditioning, and photocell outputs all require a robust comparator to convert analog levels into discrete logic. The LM2903EDR2G's single-supply operation simplifies integration into 24 V industrial control panels where no negative rail exists, and its open-collector output interfaces cleanly to PLC digital inputs through a pull-up to the panel's logic voltage. The extended temperature grade keeps thresholds specified in hot cabinets and cold outdoor enclosures. Designers typically add 10-100 mV of hysteresis via positive feedback around the 2-6 MOhm range and a small input RC filter to reject contact bounce and industrial EMI, exploiting the comparator's ground-sensing PNP input stage.
پێشنیارکراو
Square-Wave and Relaxation Oscillators
A single comparator channel of the LM2903EDR2G forms a classic relaxation oscillator: positive feedback sets two trip levels around the non-inverting input while an RC network charges and discharges on the inverting input, producing a square wave whose frequency is set by f = 1 / (2 x R x C x ln3) for a symmetric configuration. The part's open-collector output provides clean, rail-defined edges for clocking counters or driving optocoupler LEDs, and the output high level is set by the pull-up supply, permitting direct logic-level adaptation. The dual channels allow generating two phases or gating the oscillator on and off with the second comparator. Because the device is specified to 36 V, the same oscillator works in 5 V logic contexts and 24 V industrial timing circuits without redesign.
پێشنیارکراو
Power Supply Control and Protection
Switching and linear power supplies use comparators for soft-start supervision, current-limit sensing, and fault latching, and the LM2903EDR2G covers these roles economically with two channels per package. Its 36 V rating allows direct connection across rectified low-voltage AC buses and 24-48 V auxiliary rails, while the ground-reaching common-mode range permits low-side current-shunt sensing near 0 V - a task many single-supply comparators cannot perform. The open-collector output can directly sink the base of a protection transistor or drive an optocoupler for galvanically isolated fault signaling to a controller. Adding 20-100 mV of hysteresis ensures clean, single-event fault latching, and the 2.0 mV-class offset keeps current-limit trip points predictable with milliohm-level shunt resistors.
پێشنیارکراو
Battery-Powered and Portable Equipment
Battery chargers and battery-management circuits need low-cost comparators for cell-voltage monitoring, charge-complete detection, and low-battery alarms. The LM2903EDR2G operates from single low-voltage supplies and its open-collector output consumes no static pull-up current when idle beyond the load path, helping battery budget in monitoring circuits. Each package monitors two cells or two thresholds - one channel for overcharge detection and one for deep-discharge warning, for example. The 36 V ceiling comfortably covers multi-cell series stacks of lead-acid and lithium chemistry when paired with resistor dividers. Designers add a few millivolts of hysteresis so the alarm output does not oscillate near the trip point as cell voltage drifts, and use the second channel with a reference such as TL431 for precise cutoffs.
پێشنیارکراو
Analog-to-Digital Threshold Interfacing
Microcontroller and logic systems frequently need to digitize a simple binary condition - has a sensor crossed a limit - without committing an ADC channel. The LM2903EDR2G performs this conversion in one channel: the sensor drives the inverting input, a divider or reference sets the threshold on the non-inverting input, and the open-collector output with a pull-up to the MCU's VDD provides a clean 0-to-3.3 V or 0-to-5 V logic signal. This level adaptation works because the output high voltage is set by the pull-up rail rather than the comparator supply, letting a 12 V or 24 V powered comparator talk directly to 3.3 V logic. A 10-50 mV hysteresis band and a small series input resistor protect against noise and overvoltage at the sensitive input pins.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2903EDR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903DR2G | LM2903VDR2 | LM2903DR | LM2903M/NOPB |
|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 |
| Maximum Supply Voltage | 36 V (±18 V) | 36 V | 42 V (extended V-grade) | 36 V | 36 V |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Temperature Grade | Extended (E suffix) | Standard LM2903 grade | Standard LM2903 grade (V = voltage option) | Industrial LM2903 grade | Industrial LM2903 grade |
| Packing | Tape and Reel (R2) | Tape and Reel | Tape and Reel | Tape and Reel | Tube / Reel (per ordering code) |
جیاکەرەوە سەرەکییەکان
- Extended temperature grade for harsh environments (بەراورد بەLM2903DR2G)
- Ground-sensing common-mode input range (بەراورد بەLM2903M/NOPB)
- Extended supply margin option in same footprint (بەراورد بەLM2903VDR2)
تێبینییەکانی دیزاین
Never leave the LM2903EDR2G outputs without a pull-up resistor - the open-collector stage cannot source current, so an unpulled output floats and reads unpredictably. Choose the pull-up value from the speed/power trade-off: 1-10 kOhm gives fast rising edges for oscillator or high-speed detection duty, while 47-100 kOhm suits slow threshold alarms where quiescent drain matters. Also remember that inputs must remain within the common-mode range even during faults; although the common-mode range includes ground, voltages below the negative rail can drive parasitic conduction, so add a series resistor to inputs that may go negative.
When comparing slowly moving signals (battery voltage ramps, thermal sensor outputs), the output will chatter as the input crosses the threshold. Add hysteresis by feeding a small fraction of the output back to the non-inverting input: with a 100 kOhm feedback resistor and a 10 kOhm source impedance on the threshold node, roughly 20-30 mV of hysteresis results (estimate - exact value depends on the divider impedance and pull-up level). This guarantees one clean transition per crossing event. Place hysteresis resistors close to the input pins and keep the threshold node impedance below about 100 kOhm so the comparator's input bias current does not shift the trip point.
Decouple VCC (pin 8) to ground (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the package, especially when the comparator drives a load that pulls supply transients - open-collector output switching can couple glitches into both channels through a shared supply impedance. Route the two comparator input pairs away from the output traces to prevent feedback-induced oscillation in linear-input regions; the LM2903 class of comparators can oscillate when the input signal source impedance is high and output coupling exists. A solid ground plane under the SOIC-8 footprint provides a stable reference for the ground-sensing input stage.
زانیاری پابەندبوون
Compliance status was not stated in the retrieved distributor listings; confirm RoHS/REACH status on the official onsemi LM2903 product page before procurement.