Texas Instruments

LM2903PW - Dual Differential Comparator, 36V TSSOP-8 | TI

MPN: LM2903PW ✓ چالاک
36 V (single supply) or +/-18 V (dual supply) Vdss 0.4 mA (typ) Id 8-TSSOP (PW) Package
MOQ: 1 |

LM2903PW گشتی

The Texas Instruments LM2903PW is a dual differential comparator with open-collector outputs, rated for supply operation up to 36 V, drawing a typical 0.4 mA of supply current per comparator, and housed in an 8-pin TSSOP package. It belongs to the industry-standard LM193/LM293/LM393/LM2903 comparator family trusted in automotive, industrial, and consumer designs.

A comparator (also called a voltage comparator) is an analog building block that compares two input voltages and drives its output to indicate which is higher. It sits within the broader hierarchy of amplifier ICs and analog signal-chain components, bridging the gap between raw sensor signals and digital logic decisions. Unlike an operational amplifier used in closed-loop gain configurations, a comparator operates open-loop with very high gain, switching its output rail-to-rail between defined logic states.

Key features of the LM2903PW include single-supply or dual-supply operation across a wide 36 V range, low supply-current drain that is largely independent of supply voltage, low input bias current of 25 nA typical per comparator, and low input offset current of 3 nA typical. The open-collector outputs allow wired-OR connections and direct interface with TTL, CMOS, and other logic families via a pull-up resistor.

Architecturally, each comparator provides high differential gain with inputs that work down to the negative supply rail (ground in single-supply systems), enabling ground-referenced sensing. The common-mode input range extends to the positive supply minus about 1.5 V. A typical response time of approximately 1300 ns suits monitoring, threshold detection, and level-shifting tasks where microsecond-scale decisions are adequate.

Typical applications include automotive sensor threshold detection, battery undervoltage lockout, zero-crossing detection for motor control, window comparators in industrial monitoring, and oscillator/timer circuits. The automotive temperature grade (up to +125 C ambient) makes the LM2903 family a default choice in vehicle environments.

Design consideration: because outputs are open-collector, every output requires a pull-up resistor to the desired logic rail; choosing a lower pull-up resistance speeds rise time but increases power dissipation.

This page adds engineering value beyond the datasheet: a parameter comparison against drop-in alternatives, practical design notes on pull-up sizing and hysteresis, application guidance, and sourcing FAQs consolidated in one place.

جێگرەوەکانی جێگۆڕکێ بۆ LM2903PW — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903PW (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Number of Channels, Package, Input Bias Current, Input Offset Current, Operating Temperature Range.

STMicroelectronics
Number of Channels: 2
Package: TSSOP-8 (8TSSOP), 8 pins
Input Bias Current: 25 nA typical
بەراوردکردن لەگەڵ LM2903PW →
Texas Instruments
Number of Channels: 2 channels
Package: 8-pin TSSOP
Input Bias Current: 3.5nA maximum
بەراوردکردن لەگەڵ LM2903PW →
Texas Instruments
Number of Channels: 2
Operating Temperature Range: 0 C to +70 C (commercial grade, LM393)
بەراوردکردن لەگەڵ LM2903PW →
Texas Instruments
Number of Channels: 2 channels
Package: 8-pin TSSOP
بەراوردکردن لەگەڵ LM2903PW →

LM2903PWR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-TSSOP (PW)
Dual differential comparator · 2 channels · Open-collector · Rail-to-rail · ±18V / 36V total · Up to 38V · 0.37mV maximum · 3.5nA maximum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903BPWR

✅ جێگرەوەی ڕاستەوخۆ
📦 8-TSSOP (PW)
B-version: 38 V max rating vs 36 V, 0.37 mV offset, 3.5 nA bias, 200 uA/comparator supply, 1 us response, 2 kV HBM ESD - all improved, pin-for-pin per TI

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM393PWG4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-TSSOP (PW)
Dual differential comparator · 2 channels · 2 V to 36 V · 2 V to 36 V · Open collector · 0.4 mA typical

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393BPWR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-TSSOP (PW)
B-version commercial grade: improved offset/bias/speed/ESD like LM2903B but 0C to +70C range

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM193PW

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-TSSOP (PW)
extended military-range family member, wider temperature coverage, same pinout and open-collector outputs, slightly higher offset current spec (3 nA typ listed for LM193)

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM2903PW زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Channels 2 comparators
جۆری دەرچوون Open-collector
Maximum Supply Voltage 36 V (single supply) or +/-18 V (dual supply)
Supply Current Per Comparator 0.4 mA (typ)
Input Bias Current 25 nA (typ)
Input Offset Current 3 nA (typ)
Response Time 1300 ns (nominal)
Input Type Rail-to-rail (to negative rail)
مەودای پلەی گەرمیی کارکردن -40C to +125C (automotive grade)
پاکێج 8-TSSOP (PW)
جۆری دامەزراندن Surface Mount
Terminal Form Gull wing
Number of Terminals 8
Temperature Grade Automotive
Typical Application General purpose, threshold detection, level shifting
Supply-Voltage Range 2 V to 36 V (single supply)

ڕێکخستنی پینی LM2903PW

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
پین 1 OUT A — Comparator A output (open-collector, requires pull-up)
پین 2 IN A- — Comparator A inverting input
پین 3 IN A+ — Comparator A non-inverting input
پین 4 VCC-/GND — Negative supply or ground (single supply)
پین 5 IN B+ — Comparator B non-inverting input
پین 6 IN B- — Comparator B inverting input
پین 7 OUT B — Comparator B output (open-collector, requires pull-up)
پین 8 VCC+ — Positive supply, up to 36 V

بەکارهێنانە باوەکان

LM2903PW گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Threshold Detection, Battery Undervoltage Lockout (UVLO), Zero-Crossing and AC Line Detection, Industrial Window Comparators, Relaxation Oscillators and Timers, Current Sensing and Overcurrent Protection.

🚗

Automotive Sensor Threshold Detection

In automotive ECUs and body-control modules, the LM2903PW compares analog sensor outputs - such as coolant temperature, oil pressure, or battery voltage dividers - against a reference threshold and drives a digital fault flag. Its -40C to +125C automotive temperature grade matches under-hood and cabin module requirements without derating. The 2 V to 36 V supply range tolerates cold-crank and load-dump conditions on the 12 V rail, while 0.4 mA per comparator keeps quiescent drain negligible for modules that must meet low standby current targets. Inputs valid down to ground simplify ground-referenced sensor interfacing, and open-collector outputs pull up to the module's 5 V or 3.3 V logic rail.

⚡

Battery Undervoltage Lockout (UVLO)

The LM2903PW is a classic building block for battery undervoltage detection: a resistor divider scales the battery voltage into one input while a reference (bandgap, TL431, or Zener) feeds the other. When the battery falls below the trip point, the open-collector output sinks and can gate an enable pin on a DC-DC converter, protecting Li-ion cells from deep discharge. The wide 36 V tolerance directly suits 12 V lead-acid and 24 V industrial battery systems, and 25 nA input bias current introduces negligible divider error, allowing megaohm-scale divider resistors that minimize standby drain in always-on monitoring circuits.

⚡

Zero-Crossing and AC Line Detection

The second comparator of the LM2903PW is frequently dedicated to zero-crossing detection for phase-angle dimming, TRIAC triggering, and synchronous switching. The AC signal is scaled and offset so both half-cycles stay inside the comparator's input common-mode range, which extends down to the negative rail - a key family strength for ground-referenced single-supply designs. The approximately 1300 ns response time yields acceptable timing jitter for 50/60 Hz mains applications, where 1300 ns corresponds to only about 0.02 degrees of phase error. Open-collector outputs allow both comparators' outputs to be wired-ORed for combined overvoltage and zero-crossing status.

🏭

Industrial Window Comparators

Industrial monitoring systems use both comparators of the LM2903PW as a window comparator: one detects overvoltage and the other undervoltage around a nominal setpoint, and the open-collector outputs wired-OR together to produce a single out-of-range flag. The 2 V to 36 V supply range fits 24 V PLC cabinets, and the automotive temperature grade covers enclosed control panels with elevated ambient temperatures. The 25 nA typical input bias current permits precision thresholds from high-impedance dividers, and outputs pull up directly to the supervisory MCU's logic rail, eliminating level-shifter circuitry between the analog front end and digital monitoring logic.

🔧

Relaxation Oscillators and Timers

With positive feedback hysteresis plus an RC network, a single LM2903PW comparator forms a robust relaxation oscillator for clock generation, LED flashers, PWM carriers, and tone outputs. The open-collector output actively discharges the timing capacitor, and the comparator's high open-loop gain produces sharp switching thresholds that give stable frequency even with supply variation, because 0.4 mA per comparator drain is largely independent of supply voltage. The dual-channel package provides a spare comparator for oscillation-amplitude limiting or duty-cycle monitoring on the same die, keeping matched thermal behavior. Typical frequencies from sub-hertz to a few hundred kilohertz are practical given the 1300 ns response time.

🔧

Current Sensing and Overcurrent Protection

The LM2903PW implements overcurrent protection by comparing the voltage across a low-side shunt resistor against a reference threshold; when load current exceeds the limit, the output asserts a fault that latches converter shutdown or triggers a retry sequence. Ground-sensing inputs that operate down to the negative rail make low-side shunt measurements straightforward with no negative supply. The 3 nA typical input offset current keeps errors small when using large shunt values for efficiency reasons, and the 36 V rating covers 24 V industrial bus systems. Adding a small hysteresis resistor from output to the reference input provides clean, chatter-free fault assertion near the trip point.

کورتەی بەرهەمە پێشنیارکراوەکان

TL431ACLPR Texas Instruments بەکارهێنراوە لە: Automotive Sensor Threshold Detection, Battery Undervoltage Lockout (UVLO), Relaxation Oscillators and Timers, Current Sensing and Overcurrent Protection LM317MDADR Regulated sensor supply rail بەکارهێنراوە لە: Automotive Sensor Threshold Detection TPS62740DSST Buck converter gated by UVLO output بەکارهێنراوە لە: Battery Undervoltage Lockout (UVLO) BT137-600E TRIAC driven by zero-crossing output بەکارهێنراوە لە: Zero-Crossing and AC Line Detection MOC3063 Opto-isolated TRIAC driver بەکارهێنراوە لە: Zero-Crossing and AC Line Detection REF5025AIDR Precision 2.5 V reference for window thresholds بەکارهێنراوە لە: Industrial Window Comparators TS321IDR Texas Instruments بەکارهێنراوە لە: Industrial Window Comparators TS921IPT STMicroelectronics بەکارهێنراوە لە: Relaxation Oscillators and Timers INA199A1DCKR Precision current-shunt amplifier feeding comparator بەکارهێنراوە لە: Current Sensing and Overcurrent Protection
What is the maximum supply voltage of LM2903PW?
The LM2903PW operates from supply voltages up to 36 V on a single supply, or +/-18 V with dual supplies. According to the TI LM2903 datasheet, the device can also start from a low 2 V supply, and the supply-current drain of about 0.4 mA per comparator is largely independent of the supply voltage, which simplifies power budgeting across wide automotive and industrial rail ranges.
What is the difference between LM2903PW and LM393PW?
The LM2903 is the automotive-grade member of the family with an operating temperature range of -40C to +125C, while the LM393 targets commercial temperatures of 0C to +70C. Both are dual open-collector comparators in the same 8-pin packages, including the TSSOP (PW) package, and are pin-for-pin interchangeable. For automotive or extended-temperature industrial designs choose the LM2903PW; for cost-sensitive consumer designs within 0C to +70C the LM393PW is the appropriate variant.
What is the best drop-in replacement for LM2903PW?
The best drop-in replacement is the LM2903BPWR from Texas Instruments. According to TI's product page, the next-generation B-version (LM2903B) is a pin-for-pin drop-in replacement for the LM2903 with upgraded functionality: lower input offset of 0.37 mV, lower input bias of 3.5 nA, lower supply current of 200 uA per comparator, faster 1 us response time, 2 kV HBM ESD rating, and a maximum rating of up to 38 V. The same TSSOP-8 footprint is preserved.
Does LM2903PW require a pull-up resistor on its output?
Yes. The LM2903PW uses open-collector outputs, which can only sink current and cannot actively drive the output high. An external pull-up resistor from each output to the desired positive rail (5 V, 3.3 V, 12 V, etc.) is required. Values from about 1 kohm to 100 kohm are typical: lower values give faster rise times and better noise immunity but consume more current when the output is low. This also permits wired-OR configurations of multiple open-collector outputs.
What is the response time of the LM2903PW comparator?
The LM2903PW has a nominal response time of approximately 1300 ns, as listed in distributor specification data for the part. The enhanced LM2903B successor improves propagation delay to about 1 us with faster output transitions. For most threshold-detection, overvoltage protection, and level-monitoring tasks this microsecond-scale response is fully adequate; applications demanding sub-microsecond switching should consider the B-version or a faster dedicated comparator family.
Where to buy LM2903PW online?
The LM2903PW is an active part manufactured by Texas Instruments and stocked through the authorized distribution channel. On this XAIPART page, submit the Request a Quote form to receive current pricing, stock status, and delivery time for the exact LM2903PW part number. XAIPART ships original, manufacturer-new components, and the quote response typically includes multiple quantity-break options for both prototype and production volumes.
What is the price of LM2903PW?
Pricing for the LM2903PW varies with order quantity and market availability, and current unit pricing is provided through the Request a Quote form on this page rather than a static list. As a mature industry-standard dual comparator in TSSOP-8 packaging, the LM2903 family generally carries one of the lowest cost-per-function positions in the comparator category. Request a quote for exact, quantity-dependent pricing as of the current date.
What is the lead time for LM2903PW?
Lead time for the LM2903PW depends on stock position at the time of ordering; this mature, high-volume part is normally available from stock with short fulfillment windows. The DigiKey listing for the companion LM2903PWR indicates ships-today stock availability for the family, which is a positive indicator for the PW package. For the exact LM2903PW delivery commitment, submit the Request a Quote form on this page and the response will include confirmed lead time.
LM2903 vs LM2903B - which is better for automotive designs?
Both are automotive-grade dual comparators, but the LM2903B is the newer generation and is better for new automotive designs. Per the TI datasheet, the LM2903B offers a 38 V maximum rating (versus 36 V), 0.37 mV offset (versus higher offset in the original), 3.5 nA input bias, 200 uA per-comparator supply current, 1 us response time, and 2 kV ESD robustness through dedicated ESD clamps. The LM2903 remains ideal for maintaining existing qualified designs where proven behavior must not change.
When should I choose LM2903PW over the LM2903B variant?
Choose the original LM2903PW when you must keep an already-qualified, released design unchanged, when legacy qualification documents reference the classic LM2903, or when procurement requires exact form-fit-function continuity with historical builds. For all new designs, the LM2903B is the recommended choice because TI positions it as a drop-in replacement with strictly improved offset, bias current, speed, ESD rating, and supply current in the identical TSSOP-8 footprint.
Can LM2903PW be used with a 3.3 V logic supply?
Yes, with a caveat. The LM2903PW comparator itself can operate from a supply as low as 2 V, so a single 3.3 V rail can power the device, and the open-collector output pulled up to 3.3 V interfaces directly with 3.3 V logic. Keep the input common-mode range in mind: inputs should stay roughly 1.5 V below the positive supply for guaranteed accuracy, while inputs down to ground are always valid in single-supply operation.
Where to download the LM2903PW datasheet PDF?
The official LM2903PW datasheet PDF is available from Texas Instruments at ti.com/lit/gpn/lm2903, which covers the LM193, LM293, LM393, LM2903, and the B-version devices in one combined document. The datasheet includes the TSSOP (PW) package pin configuration, electrical characteristics over the automotive temperature range, typical application circuits for zero-crossing detection, comparator oscillators, and wired-OR output configurations, plus package thermal data.
What is the pinout of LM2903PW in the TSSOP-8 package?
In the 8-pin TSSOP (PW) package, pin 1 is Output A, pin 2 is Inverting Input A, pin 3 is Non-Inverting Input A, pin 4 is VCC- (ground on single supply), pin 5 is Non-Inverting Input B, pin 6 is Inverting Input B, pin 7 is Output B, and pin 8 is VCC+. This pin arrangement is identical across the SOIC-8 and TSSOP-8 packages of the LM193/LM293/LM393/LM2903 family, so footprint-compatible variants swap without schematic changes. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
What can replace LM2903PW?
Pin-compatible replacements include the Texas Instruments LM2903PWR (identical die in tape-and-reel packing), the improved LM2903BPWR drop-in successor, and the LM393PW / LM393BPWR commercial-temperature variants in the same TSSOP-8 package. The LM193PW shares the same pinout for extended-range designs. When substituting, verify the operating temperature range required by your application: only the LM2903 and LM193 variants cover -40C to +125C, while LM393 variants stop at +70C ambient.
What are the key specifications of LM2903PW that engineers should know?
The LM2903PW is a dual differential comparator with open-collector outputs in 8-pin TSSOP. Key specifications: 36 V maximum single-supply voltage (2 V to 36 V operating range), 0.4 mA typical supply current per comparator, 25 nA typical input bias current, 3 nA typical input offset current, approximately 1300 ns response time, and -40C to +125C automotive temperature range. Outputs require external pull-up resistors and support wired-OR connections. These figures come from the TI LM2903 datasheet and distributor parametric listings.

داتای سەرچاوەی ئەندازیاری بۆ LM2903PW — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM2903PW for automotive and extended-temperature industrial designs already qualified around the classic LM2903 family behavior, or when matching an existing BOM exactly. For every new design, prefer the LM2903BPWR: TI positions it as a pin-for-pin drop-in upgrade with a 38 V maximum rating, lower 0.37 mV offset, 3.5 nA input bias, 200 uA per-comparator supply current, 1 us response, and 2 kV ESD robustness in the identical TSSOP-8 package. If your product operates only within 0C to +70C, the LM393PW or LM393BPWR variants in the same footprint may reduce cost. For extended-range applications below -40C, the LM193PW shares the pinout with wider coverage. All listed variants preserve the same 8-pin TSSOP footprint, so PCB layout reuse is straightforward across the family.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2903PWR LM2903BPWR LM393PW LM193PW
Package 8-TSSOP (PW) 8-TSSOP (PW) - same 8-TSSOP (PW) - same 8-TSSOP (PW) - same 8-TSSOP (PW) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Maximum Supply Voltage 36 V 36 V 38 V 36 V 36 V
Supply Current Per Comparator 0.4 mA typ 0.4 mA typ 200 uA typ 0.4 mA typ 0.4 mA typ
Input Bias Current 25 nA typ 25 nA typ 3.5 nA typ 25 nA typ 25 nA typ (3 nA offset current)
Response Time 1300 ns 1300 ns 1 us 1300 ns 1300 ns
Operating Temperature Range -40C to +125C -40C to +125C -40C to +125C 0C to +70C -55C to +125C
Automotive Grade Yes Yes Yes No (commercial grade) Extended range

جیاکەرەوە سەرەکییەکان

  • Automotive temperature range at commodity pricing (بەراورد بەLM393PW)
  • Drop-in successor with materially improved parameters (بەراورد بەLM2903BPWR)
  • Trade-off: slower than the B-version (بەراورد بەLM2903BPWR)

تێبینییەکانی دیزاین

Always fit a pull-up resistor on each open-collector output. Choose the pull-up rail (5 V, 3.3 V, 12 V) to match downstream logic; the comparator output only sinks current. For rise-time-critical signals use 2.2 kohm to 4.7 kohm; for power-sensitive standby designs use 47 kohm to 100 kohm and accept slower edges. Estimate: with a 10 kohm pull-up to 5 V, low-state sink current is about 0.5 mA per output, well within device capability.

Slow-moving input signals near the threshold cause output chatter and multiple transitions. Add positive-feedback hysteresis: for example, a resistor from output to the non-inverting input (typically 100 kohm to 1 Mohm) creates a trip window sized by the pull-up divider. Also keep input common-mode voltage about 1.5 V below VCC+ for guaranteed accuracy per the TI datasheet; inputs near the positive rail can produce inverted or erroneous output states.

Decouple VCC+ with a 100 nF ceramic capacitor placed within a few millimeters of pin 8 to pin 4, especially when the same rail feeds inductive or switching loads. Ground-referenced inputs should route away from output traces to avoid feedback through shared ground impedance; use a solid ground plane under the TSSOP footprint. Because both comparators share one die, heavy switching on comparator A can couple small glitches into comparator B - add hysteresis and decoupling before relying on the second channel in precision monitoring.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status for the PW (TSSOP) package was not present in the retrieved source data. TI lists the device as automotive temperature grade; verify RoHS/REACH status on the TI.com product page for the exact orderable part number before release.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2903PW datasheet LM2903PW datasheet pdf LM2903PW pinout LM2903PW equivalent LM2903PW replacement LM2903PW vs LM2903PWR LM2903PW price LM2903PW stock Texas Instruments LM2903PW LM2903 TSSOP-8 dual comparator LM2903PW drop-in replacement LM2903 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM2903PW LM2903 LM2903B LM2903PWR LM393 LM193 TL431 dual differential comparator comparator amplifier IC open-collector output TSSOP-8 TSSOP surface mount automotive grade RoHS undervoltage lockout zero-crossing detection window comparator wired-OR input offset voltage response time
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ