LM2903VQPWRG4 - 18V Dual Open-Collector Comparator | TI
MPN: LM2903VQPWRG4 ✓ چالاکLM2903VQPWRG4 گشتی
A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the comparator hierarchy, where a differential comparator feeds logic-level decision circuits, sensor interfaces, threshold detectors, and industrial control equipment. Its rail-to-rail input behavior is particularly useful when sensing signals near the supply rails.
Key features include a low typical supply-current drain of 0.4 mA per comparator, an 18 V maximum supply rating, and 0.3 microsecond response time. The open-collector outputs allow the output node to be pulled up to the system logic voltage, providing flexible voltage-level interfacing. The two channels operate independently, permitting one package to implement two comparison functions or two separated threshold decisions.
The V-suffix LM2903 family supports a wide range of supply voltages and retains operation from single or dual supplies. Its common-mode input range can extend close to the supply rails, while the open-collector outputs can sink external-device current when the comparison result is low. These characteristics make the comparator suitable for both low-voltage sensing systems and higher-voltage industrial interfaces.
Typical applications include industrial process-limit detection, power-supply sequencing, sensor threshold conditioning, battery monitoring, and overvoltage or undervoltage protection. Two channels can also implement a window comparator by comparing an input signal against separate upper and lower reference thresholds. The 8-TSSOP footprint supports compact surface-mount layouts where channel density and PCB area are important.
When designing around the LM2903VQPWRG4, add a pull-up resistor to each open-collector output and account for the output leakage and sink-current limits when choosing its logic level. Keep input and output routing compact, maintain adequate supply decoupling, and verify that all sensed voltages remain within the device's operating limits.
This page combines manufacturer specifications, pin-level guidance, drop-in alternatives, application analysis, and design considerations to support faster component selection and PCB implementation.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903VQPWRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903VQPWRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Output Type, Comparator Type, Package, Number of Channels, Operating Temperature Range.
LM2903VQPWRQ1
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903VYPWR
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903VQPWRQ1
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →TS862IPT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2902YPT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903VQPWRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Supply Voltage Rating | 18 V |
| Response Time | 0.3 us |
| جۆری دەرچوون | Open collector |
| Input Common-Mode Range | Rail-to-rail |
| Supply Configuration | Single supply or dual supplies |
| Supply Current Drain | 0.4 mA typical per comparator |
| پاکێج | 8-TSSOP (PW) |
| Package Width | 4.40 mm |
| جۆری دامەزراندن | Surface mount |
| Product Classification | Standard general-purpose comparator |
| Channel Independence | 2 independent channels |
ڕێکخستنی پینی LM2903VQPWRG4
| پین 1 | OUT1 — Channel 1 open-collector output |
| پین 2 | IN1− — Channel 1 inverting input |
| پین 3 | IN1+ — Channel 1 non-inverting input |
| پین 4 | GND — Ground reference |
| پین 5 | IN2+ — Channel 2 non-inverting input |
| پین 6 | IN2− — Channel 2 inverting input |
| پین 7 | OUT2 — Channel 2 open-collector output |
| پین 8 | VCC — Positive supply voltage |
بەکارهێنانە باوەکان
LM2903VQPWRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Voltage Threshold Detection, Power-Supply Sequencing and Protection, Battery Pack Monitoring, Sensor Signal Conditioning, Window Comparator for Limit Control, Automotive and Heavy Equipment Interlocks.
Industrial Voltage Threshold Detection
LM2903VQPWRG4 fits industrial threshold monitoring because its two independent differential channels can compare a process signal against independent upper and lower limits. The 18 V supply rating supports a broader input range than many low-voltage comparator families, while the 0.3 microsecond response time allows prompt state changes. Place one channel on the rising threshold and the other on the falling threshold to create a window comparator. Open-collector outputs can pull up to the voltage used by a controller input, but each output requires an external pull-up resistor and suitable logic-level transient protection.
پێشنیارکراو
Power-Supply Sequencing and Protection
LM2903VQPWRG4 can supervise several supply rails by comparing divided feedback voltages against reference levels. Its 18 V rating accommodates monitored rails that are higher than typical low-voltage logic supplies, and the two-channel architecture permits one rail to control another. The open-collector outputs suit wired-AND fault signals because several comparator outputs can share a pull-up node. Design the divider values so normal rail tolerances do not cause false transitions, and account for comparator offset voltage when the protection threshold must remain accurate.
پێشنیارکراو
Battery Pack Monitoring
LM2903VQPWRG4 is useful for monitoring battery-derived voltages against configurable limits because its inputs can operate near the supply rails. The low 0.4 mA typical supply-current drain per comparator helps preserve available battery energy, while the 0.3 microsecond response time permits rapid overvoltage or undervoltage detection. Use the two channels for separate pack conditions or combine them for upper and lower limits. A resistor divider and appropriately protected sensing network are required because individual battery cells, traces, and connectors can present large transients.
پێشنیارکراو
Sensor Signal Conditioning
LM2903VQPWRG4 converts a conditioned sensor signal into a logic-compatible threshold decision. Its differential inputs help reject common-mode noise when the sensor is referenced near ground, and rail-to-rail operation supports sensing near the limits of a compact supply. The 0.3 microsecond response time is more than adequate for slow industrial sensors, temperature sensors, and simple control loops. Connect the open-collector output through a pull-up resistor to the receiving logic rail, and keep the sensor ground and comparator ground arrangement clean to avoid introducing errors in the decision threshold.
پێشنیارکراو
Window Comparator for Limit Control
LM2903VQPWRG4 implements an upper-and-lower limit monitor using one channel for each threshold. The two open-collector outputs can drive separate state indicators or share a wired-AND pull-up network, allowing the system to recognize any out-of-range condition. The 18 V supply rating supports monitoring of higher-voltage industrial systems, and the 0.3 microsecond response time reduces the interval between crossing a threshold and changing the output state. Resistor-divider accuracy, input offset, and logic-family thresholds must be considered together when defining acceptable operating limits.
پێشنیارکراو
Automotive and Heavy Equipment Interlocks
LM2903VQPWRG4 can support equipment-interlock logic by detecting unsafe sensor or supply conditions and presenting a wired logic result. The open-collector architecture allows output sinking into a protected controller input, while the 18 V rating supports industrial and vehicle-related interfaces when the complete electrical limits are respected. Two channels can monitor separate interlocks such as pressure and temperature. For automotive production designs, select a part with the required automotive qualification, and add transient protection because wiring harnesses can introduce voltage spikes beyond normal operating conditions.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2903VQPWRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903VQPWR | LM2903VYPWR | LM2903VQPWRQ1 | TS862IPT |
|---|---|---|---|---|---|
| Package | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Number of Channels | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector |
جیاکەرەوە سەرەکییەکان
- Matches the headline operating specifications of the cross-brand comparator (بەراورد بەTS862IPT)
- Maintains the LM2903V ordering family and function (بەراورد بەLM2903VYPWR)
- Provides two independent threshold channels in one package (بەراورد بەTS862IPT)
تێبینییەکانی دیزاین
Place the pull-up resistor close to each open-collector output so that trace capacitance does not slow the rising edge excessively. Route the two channels separately when one channel may switch rapidly while the other carries a sensitive threshold signal. Keep the comparator ground return away from high-current switching paths and connect it to a quiet ground region to reduce output-state errors.
Treat both inputs as high-impedance nodes and minimize their copper area where possible. If a sensing trace can pick up noise, compare the signal against a reference at the comparator rather than at a distant source. A small feedback resistor can add hysteresis and prevent repeated output transitions when the input changes slowly around the threshold, but its value must be selected with the circuit's noise and bias-current requirements in mind.
Do not operate an open-collector output without an external pull-up, and do not exceed the comparator's output sink-current limit when selecting that resistor. Also avoid applying voltages beyond the specified absolute-maximum input and supply ranges. For signal-node protection, use series resistance or appropriately rated clamping devices rather than relying on the comparator input to absorb application transients.
زانیاری پابەندبوون
The G4 ordering suffix commonly identifies a lead-free finish, but the exact package, environmental, and qualification declarations must be confirmed from the applicable Texas Instruments orderable part documentation.