LM393PW - Dual Differential Comparator, TSSOP-8 | Texas Instruments
MPN: LM393PW ✓ چالاکLM393PW گشتی
A voltage comparator is an analog circuit that compares two input voltages and outputs a digital signal indicating which is higher. Comparators sit within the broader amplifier family in the signal-chain hierarchy: comparator -> amplifier IC -> analog IC -> semiconductor. Unlike an operational amplifier, a comparator is intentionally uncompensated for fast switching between saturated output states, making it the right tool for threshold detection, level shifting, and oscillator functions.
Key features of the LM393PW include the open-collector output, which enables wired-OR configurations and direct interface with TTL, MOS, and CMOS logic at any voltage up to the supply rail. According to the Texas Instruments LM393 family product page, the common-mode input voltage range includes ground, the differential input voltage range equals the maximum-rated supply voltage of ±38 V class ratings, and the output saturation voltage is low, which minimizes voltage drop when pulling a load low. The device operates from a single 2 V to 36 V supply or dual ±1 V to ±18 V supplies, giving designers wide flexibility in power architecture.
Architecturally, each comparator uses a PNP differential input stage that allows input voltages to swing from 0 V (ground) up to within approximately 1.5 V of VCC without phase inversion. The open-collector output requires an external pull-up resistor, typically 3 kOhm to 15 kOhm, chosen to balance switching speed against current consumption. The LM393 family shares the industry-standard pinout in the 8-pin package: outputs on pins 1 and 7, inverting and non-inverting inputs on pins 2/3 and 5/6, ground on pin 4, and VCC on pin 8.
Typical applications include zero-crossing detection in AC power circuits, battery low-voltage monitoring with a hysteresis network, PWM generation and square-wave oscillators, and sensor threshold interfaces for thermistors and photodiodes. Its ability to sense near ground makes it especially useful in single-supply automotive and industrial systems.
A key design consideration: add positive feedback (hysteresis) when comparing slowly varying or noisy signals, otherwise the output may chatter as the input crosses the threshold. Size the pull-up resistor for the required rise time and logic level.
This page synthesizes distributor sourcing information, drop-in alternative analysis, and practical design notes beyond what the manufacturer datasheet provides.
جێگرەوەکانی جێگۆڕکێ بۆ LM393PW — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM393PW (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Number of Channels, Package, Input Bias Current, Input Offset Current, Operating Temperature Range.
LM393BPW
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903BPW
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM293PW
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM193PW
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903PW
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM393PW زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| کارکردن | Dual differential comparator |
| Number of Channels | 2 |
| جۆری دەرچوون | Open-collector |
| Output Compatibility | TTL, MOS, CMOS |
| Supply Voltage Range (Single) | 2 V to 36 V |
| Supply Voltage Range (Dual) | ±1 V to ±18 V |
| Differential Input Voltage Range | Equal to maximum-rated supply voltage (±38 V class) |
| Common-Mode Input Voltage Range | Includes ground |
| Output Saturation Voltage | Low (typ. ~200 mV at load) |
| مەودای پلەی گەرمیی کارکردن | 0 C to +70 C (commercial grade, LM393) |
| پاکێج | 8-TSSOP (PW) |
| جۆری دامەزراندن | Surface Mount |
| Packaging | Tube |
| دۆخی RoHS | Compliant |
ڕێکخستنی پینی LM393PW
| پین 1 | OUT A — Output A (open collector, requires pull-up) |
| پین 2 | IN A- — Inverting input A |
| پین 3 | IN A+ — Non-inverting input A |
| پین 4 | GND / V- — Ground or negative supply |
| پین 5 | IN B+ — Non-inverting input B |
| پین 6 | IN B- — Inverting input B |
| پین 7 | OUT B — Output B (open collector, requires pull-up) |
| پین 8 | VCC / V+ — Positive supply, 2 V to 36 V |
بەکارهێنانە باوەکان
LM393PW گونجاوە بۆ 6 بەکارھێنانs: Zero-Crossing Detection, Battery Low-Voltage Monitoring, PWM Generation and Oscillators, Sensor Threshold Interface, Over-Current and Over-Voltage Protection, TTL/CMOS Logic Level Interface.
Zero-Crossing Detection
The LM393PW detects the moment an AC waveform crosses 0 V, generating a synchronized digital pulse for phase-angle control, solid-state relays, and TRIAC firing circuits. Its common-mode input range including ground lets the input follow an AC signal referenced to the system ground without diode clamping, and the 36 V supply rating (plus a series resistor network on the input) tolerates transformer-tapped sensing levels typical of mains-derived supplies. The open-collector output drives an optocoupler or MCU interrupt pin directly, and the low saturation voltage keeps the low-state clean for accurate timing. Add mild hysteresis (a high-value resistor from output to the non-inverting input) to prevent multiple triggers from noise riding on the sine wave near the crossing point.
پێشنیارکراو
Battery Low-Voltage Monitoring
Comparing a divided-down battery voltage against a reference makes the LM393PW a compact low-battery alarm or load-disconnect controller. The wide 2 V to 36 V supply range lets the comparator ride on the battery rail itself across the full discharge curve, and ground-sensing capability supports low-side monitoring topologies. A resistor divider sets the trip point, and positive feedback from the open-collector output to the reference input adds hysteresis so the output does not chatter as the battery hovers near the threshold. The open-collector output can directly sink an LED indicator through a current-limiting resistor or drive the enable pin of a load switch, giving a complete battery-protection function with one 8-pin IC plus a handful of passives.
پێشنیارکراو
PWM Generation and Oscillators
With an RC timing network and positive feedback, each half of the LM393PW becomes a relaxation oscillator producing square waves or, with a filtered feedback path, a PWM signal for LED dimming, motor speed control, and small DC-DC converters. The uncompensated comparator stage switches fast between saturated states, and the open-collector output gives crisp logic-level edges compatible with MOSFET gate drivers and logic ICs. Frequency is set by the R-C product, and duty cycle by the ratio of the two threshold resistors. Because the two comparators are independent, one channel can generate the sawtooth/triangle while the other performs the duty-cycle comparison, achieving a complete analog PWM controller in a single 8-pin package at minimal cost.
پێشنیارکراو
Sensor Threshold Interface
Thermistors, photodiodes, pressure-switch outputs, and NTC temperature probes produce analog signals that the LM393PW converts into clean digital go/no-go logic. The PNP input stage senses signals referenced to ground, which matches many grounded-sensor topologies without additional biasing circuitry. A resistor divider on the second input sets the threshold from any available rail between 2 V and 36 V, so the same design scales from 3.3 V MCU systems to 24 V industrial PLC inputs. Output hysteresis is added with a single feedback resistor sized to exceed the sensor noise band. In industrial environments the comparator's tolerance of large differential input voltages protects against sensor fault conditions that would damage more sensitive CMOS inputs.
پێشنیارکراو
Over-Current and Over-Voltage Protection
The LM393PW provides fast fault detection in power supplies and motor drives by comparing a current-sense voltage (from a shunt or current transformer) against a reference threshold. Its differential input voltage range equals the maximum-rated supply voltage, so the inputs survive fault transients that would damage precision comparators, and the low saturation voltage produces a decisive trip signal. On trip, the open-collector output can pull low to disable a PWM controller, latch a shutdown flip-flop, or fire a crowbar circuit. Response is fast enough for hard over-current events in switch-mode converters. Designers typically add small RC filtering on the sense input to reject switching noise and a small hysteresis band to prevent repetitive tripping near the threshold boundary.
پێشنیارکراو
TTL/CMOS Logic Level Interface
Because the open-collector output of the LM393PW can be pulled up to any logic voltage independent of the comparator's own supply, it serves as a level translator between analog domains and digital systems. A comparator running on 24 V can safely signal into a 3.3 V MCU by pulling the output up to 3.3 V, with no additional level-shifting components. The output is explicitly compatible with TTL, MOS, and CMOS logic per the TI product page, and multiple outputs can share one pull-up node to implement wired-OR fault aggregation across several monitored rails. This flexibility makes the LM393 a default choice in mixed-voltage industrial equipment, test fixtures, and appliance control boards where analog supervision circuits feed low-voltage microcontrollers.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM393PW — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM393BPW | LM2903BPW | LM293PW | LM193PW | LM2903PW |
|---|---|---|---|---|---|---|
| Package | 8-TSSOP (PW) | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Performance Grade | Standard (LM393) | Improved B-version | Improved B-version, high temp | Standard, industrial grade | Standard, military grade | Standard, high temp |
| Operating Temperature Range | 0 C to +70 C | -40 C to +125 C (check suffix) | -40 C to +125 C | -25 C to +85 C | -55 C to +125 C | -40 C to +125 C |
| Pin Compatibility | Industry-standard LM393 8-pin | Pin-to-pin identical | Pin-to-pin identical | Pin-to-pin identical | Pin-to-pin identical | Pin-to-pin identical |
| RoHS | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
جیاکەرەوە سەرەکییەکان
- Lowest cost for dual open-collector comparator function (بەراورد بەLM393BPW)
- Common-mode input range includes ground (بەراورد بەLMV393 (functional cross-brand equivalent))
- Temperature grade scalability within one footprint (بەراورد بەLM193PW)
تێبینییەکانی دیزاین
Always add hysteresis when comparing slowly varying or noisy signals. Without positive feedback, the output chatters as the input crosses the threshold, producing false multiple triggers and EMI. A single resistor from each output to its non-inverting input, sized against the source impedance, provides tens of millivolts of hysteresis. Also remember the open-collector output floats high without a pull-up resistor - an omitted pull-up is the most common bring-up failure with this family.
The common-mode input range extends to ground but stops roughly 1.5 V below VCC; inputs driven within ~1.5 V of VCC lose accuracy or invert phase. Keep the highest expected input voltage at least 1.5 V below the supply rail, or raise VCC. Bypass VCC with 0.1 uF ceramic close to pin 8, since the bipolar input stage draws current spikes at switching that can couple into shared analog rails.
Place the pull-up resistors and threshold divider close to the comparator pins and route the sense traces away from switching nodes. For zero-crossing and PWM circuits, keep the RC timing components on the same ground island as pin 4 to avoid ground-bounce-induced jitter. The TSSOP-8 footprint is footprint-compatible across the whole LM193/LM293/LM393/LM2903 family, so design the land pattern once for future grade swaps.
زانیاری پابەندبوون
RoHS compliant per distributor product listings for LM393PW. Commercial-grade part; the LM2903 family covers automotive temperature requirements.