Texas Instruments

LM2903QDRG4 - 36 V Dual Comparator | Texas Instruments

MPN: LM2903QDRG4 ✓ چالاک
36 V Vdss 0.4 mA typical Id 8-pin SOIC Package
MOQ: 1 |

LM2903QDRG4 گشتی

The Texas Instruments LM2903QDRG4 is a dual differential analog comparator with two independent comparison channels, an open-collector output, and an 8-pin SOIC package. The device supports single-supply or dual-supply operation over a wide voltage range up to 36 V, while each comparator typically consumes 0.4 mA. It is specified for an ambient temperature range of -40°C to +125°C.

An analog comparator is an integrated circuit that compares two input voltages and produces a digital-level result indicating which input is higher. The LM2903 belongs to the comparator hierarchy within amplifier and interface ICs, providing a simple alternative to a general-purpose operational amplifier used only for voltage comparison. Its open-collector outputs can sink external pull-up current and support wired logic, level translation, or open-drain bus arrangements.

The two comparators operate independently, allowing one package to implement two sensing or threshold functions. Low typical input bias current of 25 nA helps minimize disturbance on high-impedance sensor circuits. The low supply-current drain, reported as 0.4 mA typical per comparator, is useful in battery-powered equipment where continuous comparator consumption affects available operating time.

The LM2903 can operate from a single positive supply or from two supplies when their voltage difference is between 2 V and 36 V. In dual-supply use, the positive supply must remain at least 1.5 V above the negative supply referenced by the device. This flexibility supports comparator designs around 5 V, 12 V, 24 V, and split-rail industrial systems.

Typical applications include battery threshold detection, industrial sensor interfaces, overvoltage and undervoltage supervision, window comparators for analog signals, and open-drain alarm signaling. Because each output is open collector, a pull-up resistor is required when the output must drive a conventional logic-high state. The open-collector architecture also permits several comparators to share a common pull-up when wired logic is appropriate.

PCB design should keep input and output traces short, provide a solid ground return, and place input filtering close to the relevant pins. Because an open-collector output cannot source current, size the pull-up resistor to balance rising time, signal current, and power dissipation. The -40°C to +125°C rating supports industrial temperature ranges, although the complete system still requires suitable thermal verification.

This product page combines the exact LM2903QDRG4 ordering information with package, pinout, sourcing, comparison, and application guidance. It helps engineers distinguish verified pin-compatible options from devices that merely use a similar 8-pin package but differ in electrical behavior, qualification, or supply requirements.

جێگرەوەکانی جێگۆڕکێ بۆ LM2903QDRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903QDRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Number of Channels, Supply Current, Comparator Type, Output Type.

Texas Instruments
Package: 8-pin SOIC, 0.154 inch (3.90 mm) width
Number of Channels: 2 channels
Output Type: Open-collector
بەراوردکردن لەگەڵ LM2903QDRG4 →
Texas Instruments
Package: 8-SOIC, 0.154 in (3.90 mm) body width
Supply Current: 200 uA per comparator
Comparator Type: General Purpose
بەراوردکردن لەگەڵ LM2903QDRG4 →
Texas Instruments
Package: 8-pin SOIC, 5.30 mm width
Number of Channels: 2 channels
Supply Current: 0.4 mA typical per comparator
بەراوردکردن لەگەڵ LM2903QDRG4 →
Texas Instruments
Number of Channels: 2
Supply Current: 0.4 mA per comparator
بەراوردکردن لەگەڵ LM2903QDRG4 →
Texas Instruments
Number of Channels: 2 channels
بەراوردکردن لەگەڵ LM2903QDRG4 →

LM2903DG4

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · Single or dual supply · 32 V · 30 V · 0.4 mA typical per comparator · Open-collector · TTL, MOS, and CMOS compatible

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903MX

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
General Purpose · 2 · 2 V to 36 V · 1 V to 18 V · 1.3 us · Open-Collector · Rail-to-Rail · CMOS, MOS, TTL

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903PSRG4

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
Dual differential comparator · 2 channels · Open collector · 36 V · 2 V to 36 V · 0.4 mA typical per comparator · 25 nA · -40°C to +125°C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904LVQDRQ1

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
General-purpose operational amplifier · 2 channels · 2 amplifiers · 5.5 V · 2.7 V to 5.5 V · 1 MHz · 3 mV · Automotive grade

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903QDRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Comparator Type Dual differential comparator
Number of Channels 2 independent channels
جۆری دەرچوون Open collector
Maximum Supply Voltage 36 V
Single-Supply Operating Range 2 V to 36 V
Dual-Supply Total Range 2 V to 36 V
Minimum Positive Supply Offset 1.5 V
Supply Current Per Comparator 0.4 mA typical
Input Bias Current 25 nA typical
مەودای پلەی گەرمیی کارکردن -40°C to +125°C
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount
Automotive Qualification Coding G4 ordering suffix

ڕێکخستنی پینی LM2903QDRG4

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT1 — Open-collector output for comparator 1
پین 2 IN1- — Inverting input for comparator 1
پین 3 IN1+ — Non-inverting input for comparator 1
پین 4 GND — Ground connection
پین 5 IN2+ — Non-inverting input for comparator 2
پین 6 IN2- — Inverting input for comparator 2
پین 7 OUT2 — Open-collector output for comparator 2
پین 8 VCC — Positive supply connection

بەکارهێنانە باوەکان

LM2903QDRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial 24 V Threshold Detection, Battery Pack Overvoltage Detection, Automotive Sensor Window Comparator, High-Impedance Sensor Interface, Open-Drain Alarm and System Interlock, Analog Window Limit Circuit.

🏭

Industrial 24 V Threshold Detection

The LM2903QDRG4 is well suited to industrial 24 V monitoring because the LM2903 family supports supply voltages up to 36 V and is specified across -40°C to +125°C. Place one channel across a divided sensor signal and use the open-collector output to pull down an alarm line. The typical 0.4 mA supply-current draw per comparator suits continuously powered monitoring equipment, while the 25 nA typical input bias current minimizes loading on high-impedance dividers. A pull-up resistor is required on each open-collector output and should be selected for the alarm-line voltage and required rise time.

⚡

Battery Pack Overvoltage Detection

LM2903QDRG4 can monitor a battery-derived rail for an overvoltage condition without requiring a high-speed amplifier. One differential channel compares a resistor-divider reference with the divided battery voltage, and the open-collector result provides a fault indication suitable for an MCU or power-management system. Its typical 0.4 mA current per comparator limits standing consumption, while the 25 nA typical input bias current helps prevent divider error in higher-impedance designs. The supply must remain within the LM2903 operating limits, and the complete threshold network should account for resistor tolerance and temperature drift.

🚗

Automotive Sensor Window Comparator

The LM2903QDRG4 fits automotive sensing systems that require a valid sensor-range check and can operate from -40°C to +125°C. Two independent channels can monitor upper and lower thresholds, or one channel can compare a sensor signal with a reference while the other performs a redundant or complementary decision. The open-collector outputs support pulled-up diagnostic or load-shed signals. Because the G4 ordering designation identifies the intended automotive option, use that designation when validating qualification requirements. Check the absolute maximum ratings, input common-mode range, and output-load capability against the vehicle environment.

🧩

High-Impedance Sensor Interface

The LM2903QDRG4 is appropriate for slow, high-impedance sensor signals where the comparator's typical 25 nA input bias current is small compared with the source impedance. It can convert an analog sensor voltage into a logic-compatible threshold event without continuously operating a general-purpose amplifier as a comparator. The two channels allow separate threshold and alarm decisions within one package. Input traces should be short and guarded against adjacent switching nodes, while the pull-up resistor on the open-collector output determines the logic-high level and signal rise time. Add input filtering if the sensor node is exposed to noise.

🔧

Open-Drain Alarm and System Interlock

Two LM2903QDRG4 channels can implement independent alarm or interlock functions while sharing a common open-drain wiring arrangement. This is useful in equipment where several fault conditions must produce one active-low summary signal. Each output can sink the pull-up current, and the package's typical 0.4 mA per-comparator consumption supports always-on protection circuits. The output sink rating, pull-up voltage, and system fault polarity must be checked in the final design. Avoid relying on the open-collector output as a source of high current; use it only within the device's specified output-loading conditions.

📺

Analog Window Limit Circuit

The LM2903QDRG4 can monitor whether an analog signal lies below, above, or between two limits by using its two independent differential channels. One channel can detect the lower threshold and the other the upper threshold, producing complementary open-collector states for a window-control signal. The wide supply range supports signal systems operating well above conventional 5 V logic levels, while the low input bias current reduces loading. Design the reference and divider networks with suitable tolerance, and verify that the monitored signal remains within the comparator's specified common-mode range. Output rise time should be checked against the pull-up resistance and cable or bus capacitance.

What is the operating voltage range of LM2903QDRG4?
The LM2903QDRG4 supports operation from a single supply or from two supplies with a total voltage difference of 2 V to 36 V. In a split-supply configuration, the positive supply must be at least 1.5 V above the negative supply reference. According to the Texas Instruments LM2903 datasheet, this range supports conventional 5 V, 12 V, and 24 V supply designs while accommodating higher industrial bus voltages.
How much current does each LM2903 comparator consume?
Each LM2903 comparator typically consumes 0.4 mA, giving approximately 0.8 mA for both channels under the stated typical condition. This low supply-current drain is particularly useful in battery-powered monitoring equipment, where the comparator can remain active continuously without imposing a large standing load. The Texas Instruments LM2903 datasheet describes the supply-current drain as largely independent of supply voltage.
Where can I download the LM2903QDRG4 datasheet PDF?
The official LM2903QDRG4 datasheet and ordering information are available from the Texas Instruments LM2903 product page at https://www.ti.com/product/LM2903. The specific device is identified as LM2903QDRG4, a dual differential comparator in an 8-pin SOIC package. Use the manufacturer document for the definitive pin description, electrical limits, test conditions, and ordering table.
Where can I find the LM2903QDRG4 pinout?
The LM2903QDRG4 uses an 8-pin SOIC package with pins 1 and 7 assigned to the two open-collector outputs, pins 2 and 6 to the inverting inputs, pins 3 and 5 to the non-inverting inputs, pin 4 to ground, and pin 8 to the positive supply. Use the pin-description table in the Texas Instruments LM2903 datasheet when assigning PCB tracks and polarity-sensitive components.
What are the key specifications of LM2903QDRG4 that engineers should know?
The LM2903QDRG4 is a dual differential comparator with a 36 V maximum supply voltage, 0.4 mA typical supply current per channel, 25 nA typical input bias current, and an operating temperature range of -40°C to +125°C. It provides open-collector outputs in an 8-pin SOIC. These specifications place it in the low-power, wide-supply comparator category for industrial monitoring and threshold-detection circuits.
What can replace LM2903QDRG4?
The closest verified same-manufacturer options are LM2903DG, LM2903MX, LM2903PSRG4, and LM2904LVQDRQ1, all considered only after confirming their ordering codes, temperature grades, and electrical limits against the required circuit. The LM2903DG and LM2903MX preserve the 8-pin SOIC architecture, while the exact automotive or rail-to-rail requirements determine whether the LM2904 option is electrically appropriate.
Is LM2903QDRG4 the same as LM2903DG?
Both devices use the 8-pin SOIC comparator architecture, but their ordering codes identify different qualification or temperature options. The LM2903QDRG4 carries the G4 automotive designation, whereas LM2903DG represents a different orderable version of the LM2903 family. They are mechanically compatible on the same 8-pin SOIC land pattern, but functional interchangeability still requires checking input range, output behavior, temperature grade, and qualification.
LM2903QDRG4 vs LM2904LVQDRQ1: which is better for automotive sensing?
The LM2903QDRG4 is the better choice when a proven LM2903 dual-comparator circuit is already designed around the LM2903 electrical behavior. The LM2904LVQDRQ1 adds a different rail-to-rail-focused implementation and carries a Q1 automotive designation, making it worth evaluating for newer low-voltage sensing designs. Because the rail-to-rail input specification may change usable common-mode range, verify both devices against the actual sensor voltage rather than relying only on package compatibility.
When should I choose LM2903QDRG4 over LM2903DG?
Choose LM2903QDRG4 when the application requires the LM2903 family with the G4 automotive ordering designation and operation across -40°C to +125°C. Choose LM2903DG when its electrical limits, qualification level, and temperature grade satisfy the design and the 8-pin SOIC footprint is already accepted. Both parts should be compared by complete ordering information because the family suffix encodes more than package shape.
Is LM2903QDRG4 suitable for 24 V industrial applications?
The LM2903QDRG4 is suitable for 24 V industrial threshold-detection applications because the LM2903 family supports supply voltages up to 36 V and is rated from -40°C to +125°C. Use a properly rated pull-up resistor and confirm that the sensed input remains within the comparator's common-mode limits. The Texas Instruments LM2903 datasheet should be used to validate absolute maximum and recommended operating conditions.
What is the best drop-in replacement for LM2903QDRG4?
LM2903DG is the most direct verified drop-in candidate because it retains the 8-pin SOIC LM2903 architecture, while LM2903MX and LM2903PSRG4 provide additional ordering options for review. No cross-brand equivalent has been established here with enough electrical detail to claim unconditional drop-in status. Confirm pinout, common-mode range, output sink capability, propagation delay, temperature grade, and automotive qualification before substitution.
What is the best Texas Instruments equivalent for LM2903QDRG4?
LM2903DG is the leading same-manufacturer equivalent to evaluate because it uses the same 8-pin SOIC LM2903 format and can preserve an existing board layout. LM2903MX and LM2903PSRG4 are additional LM2903-family alternatives, while LM2904LVQDRQ1 may suit rail-to-rail automotive sensing. The best choice depends on the required common-mode range, output load, qualification, and orderable temperature range.
Where can I buy LM2903QDRG4 online?
Use the Request a Quote form on this page to request LM2903QDRG4 pricing, stock confirmation, lead time, and order quantities. The manufacturer identifies the device as an 8-pin SOIC dual differential comparator, and the product page provides its technical documentation. The quote form allows the exact suffix and required quantity to be reviewed without substituting a different package or qualification code.
What is the price of LM2903QDRG4?
Current pricing for the exact LM2903QDRG4 should be obtained through the Request a Quote form on this page. The form records the required quantity and order configuration so the response can reflect the correct 8-pin SOIC device with its G4 ordering suffix. No fixed price is published here because component pricing and availability can change with quantity, market conditions, and manufacturing status.
What is the lead time and stock status of LM2903QDRG4?
Request the current lead time, stock position, and minimum order quantity through the Request a Quote form on this page. Texas Instruments identifies LM2903QDRG4 as an orderable part in an 8-pin SOIC package, but live inventory varies by quantity and date. Include your required delivery schedule and packaging preference so the quotation can be reviewed against the actual production plan.

داتای سەرچاوەی ئەندازیاری بۆ LM2903QDRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM2903QDRG4 for dual-channel threshold detection where the design needs a wide 2 V to 36 V supply range, open-collector outputs, low typical bias current, and operation across -40°C to +125°C. Its G4 ordering designation is appropriate for automotive programs that require that qualification route. Choose LM2903DG when its exact qualification and temperature configuration fit the product and the existing board already uses the 8-pin SOIC LM2903 layout. Consider LM2903MX or LM2903PSRG4 when their orderable temperature, qualification, or commercial terms better match production needs. Evaluate LM2904LVQDRQ1 for new low-voltage rail-to-rail sensing designs, especially automotive Q1 requirements, but verify its input common-mode range and output behavior before replacing an LM2903 circuit. No unqualified cross-brand replacement is recommended.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2903DG LM2903MX LM2903PSRG4 LM2904LVQDRQ1
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Comparator Configuration Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator
Automotive Ordering Option G4 ordering suffix Different ordering option Different ordering option G4 ordering family Q1 ordering option

جیاکەرەوە سەرەکییەکان

  • Wide supply range supports industrial and automotive signal environments (بەراورد بەLM2904LVQDRQ1)
  • Low input bias supports higher-impedance sensing networks (بەراورد بەLM2904LVQDRQ1)
  • Direct LM2903 family ordering choice for G4 designs (بەراورد بەLM2903DG)

تێبینییەکانی دیزاین

Every open-collector output requires a pull-up resistor when the next circuit expects a driven logic-high state. Calculate the resistor from the pull-up voltage, required sink current, and allowable rise time rather than selecting it solely by logic convention. The pull-up must remain within the LM2903 output ratings. If several outputs share a common line, ensure that the combined sink current and bus capacitance still meet the device's switching and output-current limits.

Route the differential input pair for each comparator as a compact, tightly coupled pair and keep it away from switching nodes, inductors, and high-current power paths. Place threshold-setting or input-filtering components close to the associated input pins to minimize parasitic pickup. Connect the ground pin directly to a low-impedance ground plane and bypass the supply close to pin 8. This arrangement is particularly important because the device is commonly used to detect small threshold changes in noisy industrial environments.

Do not assume that open-collector means the output can source current; the output primarily sinks current to ground. Also verify that the input voltage remains inside the comparator's common-mode range even when the supply is above 36 V. A common error is replacing the device solely because both parts have eight pins. Before substitution, check polarity, output topology, propagation delay, input offset, output sink current, temperature grade, and automotive qualification rather than relying only on the SOIC-8 footprint.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The G4 ordering suffix identifies an automotive-oriented ordering option, but a specific AEC-Q100 qualification statement, RoHS declaration, REACH declaration, lead-free statement, halogen-free statement, and conflict-minerals declaration require confirmation from the manufacturer product documentation.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2903QDRG4 datasheet LM2903QDRG4 pinout LM2903QDRG4 datasheet pdf LM2903QDRG4 specifications LM2903QDRG4 equivalent LM2903QDRG4 replacement LM2903QDRG4 cross reference LM2903QDRG4 vs LM2903DG LM2903QDRG4 vs LM2904LVQDRQ1 LM2903QDRG4 footprint LM2903QDRG4 price LM2903QDRG4 stock Texas Instruments LM2903QDRG4 LM2903 36 V open collector comparator LM2903 automotive comparator application

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM2903QDRG4 LM2903DG LM2903MX LM2903PSRG4 LM2904LVQDRQ1 analog comparator differential comparator voltage comparator amplifier IC integrated circuit semiconductor open-collector output open-drain output single-supply operation dual-supply operation supply-current drain input bias current input common-mode range 36 V 8-pin SOIC SOIC package family surface-mount package industrial control automotive electronics
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ