LM2903VDR2G - Dual Open-Collector Comparator | onsemi
MPN: LM2903VDR2G ✓ چالاکLM2903VDR2G گشتی
A voltage comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference crosses a defined threshold. In the product hierarchy, the LM2903VDR2G is a comparator, within the broader amplifier and comparator IC family, and ultimately belongs to the semiconductor and analog signal-processing categories. The LM2903 series provides two independent comparison channels in one package, reducing board area compared with two separate single comparators.
Key features include independent comparator operation, single or split-supply capability, a common-mode input range extending to ground, and open-collector outputs that support wired-AND logic. The 1.5 µs response time is suitable for threshold monitoring and general-purpose signal conditioning, although it is not optimized for the very low latency required by high-speed edge-detection systems. The manufacturer identifies automotive, industrial, and consumer electronics as suitable application areas.
Each channel compares a non-inverting input with an inverting input. The differential input voltage can extend to ±18 V, while the 2 V to 36 V supply rating supports single-rail operation from 2 V through 36 V and split-rail operation with an input range from -1 V through 18 V on either side of ground. The open-collector transistor can sink output current while remaining in a high-impedance state when inactive, so the pull-up resistor determines the output high voltage and limits sink current.
Typical applications include battery-voltage monitoring, overvoltage and undervoltage protection, industrial control-interface detection, sensor threshold conditioning, and ground-referenced digital logic interfaces. In each case, the reference network establishes the switching threshold, while the open-collector output can drive a pull-up, relay-driver input, or logic gate. Designers should verify the required output sink current and choose a resistor value that balances current consumption against output rise time.
For reliable operation, place the pull-up resistor close to the output and maintain short input traces to reduce sensitivity to injected noise. Check input and output behavior at both supply extremes, confirm that the signal source stays within the common-mode range, and account for offset voltage when defining a precise switching threshold. The manufacturer datasheet is the controlling reference for full electrical limits, test conditions, and connection details.
This product page combines the principal LM2903VDR2G specifications, application guidance, drop-in alternatives, and design considerations to support faster component selection and PCB planning.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903VDR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903VDR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Comparator Type, Propagation Delay, Operating Temperature Range, Input Bias Current.
LM2903DR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903M/NOPB
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NCV2903VDR2G
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
NCV2903DR2G
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903YDT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903VN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903BIDR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903VDR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual independent precision voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Single-Supply Input Common-Mode Range | To ground |
| Differential Input Voltage Range | ±18 V |
| Input Offset Voltage | As low as 2.0 mV |
| Response Time | 1.5 µs |
| جۆری دەرچوون | Open-collector |
| Output Logic Capability | Wired-AND operation |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +125 °C |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Input Bias Current | 2 nA to 5 nA |
| دۆخی RoHS | ROHS3 compliant |
ڕێنمایی ڕێکخستنی پینی LM2903VDR2G 8-pin soic
ڕێکخستنی پین بۆ LM2903VDR2G (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2903VDR2G.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2903VDR2G گونجاوە بۆ 6 بەکارھێنانs: Battery Voltage Threshold Monitoring, Industrial Overvoltage Protection, Sensor Threshold Conditioning, Automotive Logic Interfacing, Ground-Referenced Window Comparison, Digital Control Interface.
Battery Voltage Threshold Monitoring
The LM2903VDR2G fits battery-pack monitoring because its 2 V to 36 V supply rating covers many portable and industrial battery systems, while the single-supply common-mode range extends to ground. A resistor divider can present a scaled battery voltage to one input and a stable reference to the other input, allowing the open-collector output to indicate when the pack crosses a selected threshold. The 2.0 mV offset-voltage capability supports finer threshold definition, while the 1.5 µs response time is suitable for ordinary power-system protection rather than high-speed event capture.
پێشنیارکراو
Industrial Overvoltage Protection
LM2903VDR2G can monitor an industrial supply rail and assert an open-collector fault signal when the input exceeds a defined limit. Its operating range of 2 V to 36 V accommodates many 24 V and 36 V control systems, and its -40 °C to +125 °C range supports temperature-variable industrial environments. The external reference and divider establish the protection threshold, while the pull-up resistor converts the open-collector state into a logic-compatible fault indication. System designers should verify transient protection separately because the comparator rating does not replace a dedicated surge-protection network.
پێشنیارکراو
Sensor Threshold Conditioning
The LM2903VDR2G is appropriate for converting a slowly varying sensor signal into a clean threshold event. One input can receive the sensor voltage or a scaled version of it, while the other receives a reference derived from the system supply. With an input offset voltage as low as 2.0 mV and a 1.5 µs response time, it works well for temperature, level, and light-sensor interfaces that need reliable switching rather than precision analog amplification. Keep sensor traces short and use the open-collector output with a suitable pull-up when driving digital logic.
پێشنیارکراو
Automotive Logic Interfacing
LM2903VDR2G can support automotive logic-level monitoring where a 2 V to 36 V supply range, ground-referenced input capability, and an extended -40 °C to +125 °C temperature range are important. The two independent channels can monitor separate vehicle signals, and their open-collector outputs can be pulled up to the logic rail used by a controller. Because an open-collector output can sink current but cannot actively drive a high level, the pull-up voltage, resistor value, and sink-current requirement must match the receiving circuit. Qualification requirements for a specific vehicle platform should be checked against the exact ordering code.
پێشنیارکراو
Ground-Referenced Window Comparison
The dual LM2903VDR2G channels can implement an upper and lower voltage window with two reference dividers and complementary pull-up outputs. This arrangement is useful for determining whether a signal lies within an acceptable operating band. The differential input range of ±18 V and common-mode operation to ground provide flexibility in ground-centered industrial systems, while the open-collector outputs can be combined for an active-low fault indication. Verify both references and output states over temperature because offset voltage and output saturation behavior affect the actual switching boundaries.
پێشنیارکراو
Digital Control Interface
LM2903VDR2G can compare an analog control voltage with a reference and provide an open-collector transition signal to a digital controller. Its 1.5 µs response time is more than sufficient for supervisory functions, while the 2 V minimum supply supports low-voltage systems. The open-collector architecture permits wired-AND signaling when several conditions must share one interrupt line. Place the pull-up near the receiving logic device, maintain a defined state during reset and power sequencing, and confirm that all signals remain within the comparator's input limits before enabling the function.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2903VDR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2903DR2G | LM2903M/NOPB | NCV2903VDR2G | NCV2903DR2G | LM2903YDT | LM2903V | LM2903 |
|---|---|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Comparator Configuration | Dual independent comparator | Dual independent comparator | Dual independent comparator | Dual independent comparator | Dual independent comparator | Dual independent comparator | Dual comparator | Dual comparator |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
جیاکەرەوە سەرەکییەکان
- Ground-referenced operation in a wide-supply dual comparator (بەراورد بەLM2903V)
- Direct same-family ordering alternatives (بەراورد بەLM2903DR2G)
- Automotive-focused ordering option in the same footprint (بەراورد بەLM2903VDR2G)
- Cross-manufacturer replacement route (بەراورد بەLM2903)
تێبینییەکانی دیزاین
An open-collector output has no active pull-up path, so an external resistor is mandatory whenever the output must reach a valid logic-high state. Choose the resistor to satisfy the receiver's input-current requirement while keeping the comparator's sink current within its rating. Confirm that the pull-up voltage does not exceed the output-pin limit and account for the longer rising edge created by capacitance and the chosen resistance.
Place the pull-up resistor close to the comparator output or receiving logic input, and keep the inverting and non-inverting input traces short. Reference-divider resistors should be positioned near the comparator when low noise is important. Avoid routing the sensitive input node beside high-current switching nodes, and use a ground return that does not share a noisy return path with relays, motors, or power-conversion components.
The 2 V to 36 V supply rating supports single-rail systems, but it does not remove the need for local supply decoupling or input-transient protection. Place the bypass capacitor close to the supply and ground pins, and size the divider so that its current is large enough to limit offset effects but small enough to avoid unnecessary supply loading. For exposed industrial or automotive wiring, add appropriate surge and reverse-polarity protection ahead of the device.
The stated 1.5 µs response time makes the LM2903VDR2G appropriate for supervisory threshold detection rather than high-speed pulse qualification. Account for propagation delay, input offset, hysteresis, and the pull-up RC rise time when defining the effective switching point. Add positive feedback for hysteresis when chatter near the threshold would be disruptive, and verify the complete threshold system across temperature rather than relying only on the nominal offset value.
زانیاری پابەندبوون
The product information identifies ROHS3 compliance. AEC-Q100, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the exact manufacturer orderable-part documentation.