onsemi

LM2904DG - Dual 1MHz Op Amp, 3-32V | onsemi

MPN: LM2904DG ✓ چالاک
3 V to 32 V Vdss 8-pin SOIC Package
MOQ: 1 |

LM2904DG گشتی

onsemi LM2904DG is a dual, general-purpose operational amplifier with two independent amplifiers, 1 MHz gain-bandwidth product, 0.6 V/us slew rate, and a 3 V to 32 V supply range in an 8-pin SOIC package. It supports single-supply or split-supply operation and accepts input common-mode voltages extending to ground and VEE.

An operational amplifier is a voltage-controlled differential amplifier used to amplify, buffer, filter, compare, or drive analog signals. The LM2904 belongs to the broader operational-amplifier hierarchy, where the dual configuration provides two signal-processing channels in one package. This makes it useful where board area, component count, and supply flexibility are more important than precision or high speed.

Key features include a 1 MHz gain-bandwidth product, 0.6 V/us slew rate, and a minimum common-mode rejection ratio of 50 dB. The device is specified for a 3 V to 32 V total supply, allowing operation from a single positive rail or from positive and negative rails. Its common-mode input range extends to ground and VEE, which supports battery-powered, industrial-control, and sensor-interface designs where input signals may approach the lower supply rail.

The input offset voltage is listed at 7 mV, making this amplifier more appropriate for general-purpose amplification than precision instrumentation applications requiring microvolt-level offset. Its moderate gain-bandwidth product and slew rate are appropriate for audio-frequency control loops, slow sensor signals, active filtering, comparators, and general analog signal conditioning. The dual architecture also allows both amplifiers to share the same supply and decoupling network.

Typical uses include DC motor and actuator feedback control, transducer buffering, low-frequency active filters, audio preamplification, regulated power-supply feedback, and general-purpose analog interfaces. Split-supply operation can simplify biasing around ground, while single-supply operation helps reduce system power and board complexity in battery-operated equipment.

Designers should account for input bias current, output-current capability, common-mode limits, and stability when driving capacitive loads. Place decoupling capacitors close to the supply pins, keep feedback routing compact, and verify output swing against the actual load. For applications requiring very low offset, very wide bandwidth, rail-to-rail output, or automotive qualification, compare the LM2904 family against more specialized amplifier families.

This product page combines manufacturer-datasheet characteristics, verified distributor listings, drop-in replacement analysis, application guidance, and package-level design notes to support faster component evaluation and PCB reuse decisions.

جێگرەوەکانی جێگۆڕکێ بۆ LM2904DG — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904DG (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Slew Rate, Common-Mode Input Range, Operating Temperature Range, Amplifier Type.

onsemi
Package: 8-SOIC (0.154 in, 3.90 mm width)
Slew Rate: 0.6 V/µs
Common-Mode Input Range: Extending to ground/VEE
بەراوردکردن لەگەڵ LM2904DG →
STMicroelectronics
Amplifier Type: General-purpose operational amplifier
بەراوردکردن لەگەڵ LM2904DG →
Texas Instruments
Package: SOIC-8 (D)
Slew Rate: 0.5 V/us (typical)
Operating Temperature Range: -40 C to +125 C
بەراوردکردن لەگەڵ LM2904DG →
Texas Instruments
Package: 8-pin VSSOP
Common-Mode Input Range: Extends to ground
Amplifier Type: General-purpose operational amplifier
بەراوردکردن لەگەڵ LM2904DG →
Texas Instruments
Package: 8-SOIC (D)
Slew Rate: 0.3 V/us
Common-Mode Input Range: Includes ground
بەراوردکردن لەگەڵ LM2904DG →
Texas Instruments
Operating Temperature Range: -40 °C to +125 °C
بەراوردکردن لەگەڵ LM2904DG →

LM2904BIDR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin SOIC
Texas Instruments · Industry-standard dual operational amplifier · 2 (Dual) · 3 V to 36 V · +/-1.5 V to +/-18 V · 1.2 MHz · 0.5 V/us (typical) · 0.5 mV typical / 3 mV maximum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904BIDR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
Texas Instruments · Industry-standard dual operational amplifier · 2 (Dual) · 3 V to 36 V · +/-1.5 V to +/-18 V · 1.2 MHz · 0.5 V/us (typical) · 0.5 mV typical / 3 mV maximum

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-pin SOIC
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904AYDT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 8-pin SOIC
2 circuits · General-purpose operational amplifier · 2 independent channels · 1.1 MHz · 0.6 V/us · 20 nA · Single positive supply

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2904DG زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Channels 2 channels
Amplifier Type Dual general-purpose operational amplifier
Gain-Bandwidth Product 1 MHz
Slew Rate 0.6 V/us
Supply Voltage Range 3 V to 32 V
Input Offset Voltage 7 mV
Common-Mode Rejection Ratio 50 dB minimum
مەودای پلەی گەرمیی کارکردن -40 C to +105 C
Common-Mode Input Range Extends to ground and VEE
Supply Configuration Single supply or split supply
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount

ڕێکخستنی پینی LM2904DG

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUTA — Amplifier A output
پین 2 INA- — Amplifier A inverting input
پین 3 INA+ — Amplifier A non-inverting input
پین 4 V- — Negative supply or ground connection for single-supply operation
پین 5 INB+ — Amplifier B non-inverting input
پین 6 INB- — Amplifier B inverting input
پین 7 OUTB — Amplifier B output
پین 8 V+ — Positive supply

بەکارهێنانە باوەکان

LM2904DG گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Signal Conditioning, DC Motor Feedback Control, Audio Preamplification, Active Filtering and Analog Control, Battery-Powered Monitoring, Power-Supply Feedback and Monitoring.

🏭

Industrial Sensor Signal Conditioning

The onsemi LM2904DG fits industrial sensor interfaces where two channels can buffer or amplify moderate-accuracy transducer signals from a shared supply. Its 3 V to 32 V operating range supports 5 V, 12 V, and 24 V systems, while the 1 MHz gain-bandwidth product accommodates signals well below that limit. The common-mode input range extending toward ground is useful when sensor outputs sit close to the lower rail. Because the listed input offset voltage is 7 mV, calibration may be necessary for high-accuracy measurement. Use the second amplifier for a reference buffer, active filter, or output driver.

⚡

DC Motor Feedback Control

The LM2904DG is appropriate for the error-amplifier and feedback stages of a basic DC motor-control loop. Its 0.6 V/us slew rate provides more bandwidth than a low-frequency precision amplifier, while the dual configuration can process a command signal and a feedback signal in one 8-pin SOIC. The 3 V to 32 V range permits operation from industrial and automotive-style intermediate rails. Choose the amplifier only after checking output-current capability, capacitive-load stability, and the motor driver's control requirements.

🎧

Audio Preamplification

The dual LM2904DG can implement two mono audio preamplifier channels or one active-filter stage plus one output-buffer stage. Its 1 MHz gain-bandwidth product is suitable for low-frequency audio and general-purpose tone shaping, and the 0.6 V/us slew rate avoids the severe slew limitation of extremely low-bandwidth amplifier variants. The 7 mV input offset is usually acceptable for audio but can contribute to DC offset in high-gain stages. Add input coupling or biasing appropriate to the selected single- or split-supply topology.

🔧

Active Filtering and Analog Control

The LM2904DG can implement first- and second-order active filters, integrators, and error amplifiers in low-bandwidth control systems. Its 1 MHz gain-bandwidth product provides useful loop bandwidth, while dual packaging allows one channel to perform filtering and the other to buffer or invert a control signal. The device operates from 3 V to 32 V, making it suitable for both compact battery-powered circuitry and 24 V industrial control boards. Validate noise, output swing, and closed-loop stability at the lowest expected supply voltage.

📱

Battery-Powered Monitoring

The LM2904DG fits battery-powered monitoring circuits that require low-power dual amplification from a 3 V to 32 V-compatible source. Its common-mode input range extending to ground helps process signals from sensors, dividers, and transducers that operate close to the lower supply rail. Two amplifiers in one 8-pin SOIC can reduce component count, and the 1 MHz bandwidth is ample for many environmental and wearable monitoring signals. Check the actual quiescent-current requirement for duty-cycled designs because that numerical limit must be confirmed from the manufacturer datasheet.

🔋

Power-Supply Feedback and Monitoring

The LM2904DG can serve as an error amplifier or analog monitor within non-isolated power-supply control and test circuits. Its 3 V to 32 V supply range permits connection to intermediate power rails, while the two amplifier channels can compare a feedback signal and monitor another node. The moderate 1 MHz gain-bandwidth product is suitable for slow regulation loops rather than high-frequency switching compensation. Confirm output swing, output-current capability, and stability with the chosen power-stage topology before using it as the primary regulator error amplifier.

What is the operating voltage of LM2904DG?
The LM2904DG operates from 3 V to 32 V across its total supply. According to the onsemi manufacturer datasheet, it can also be powered with positive and negative rails whose combined voltage remains within this range. This flexibility supports single-rail battery systems, conventional positive supplies, and split-supply analog circuits centered around ground.
What are the key specifications of LM2904DG that engineers should know?
The LM2904DG is a dual operational amplifier with a 1 MHz gain-bandwidth product, 0.6 V/us slew rate, 7 mV input offset voltage, and a 3 V to 32 V supply range. According to the onsemi manufacturer datasheet, it provides two independent amplifiers in an 8-pin SOIC and supports input common-mode voltages extending to ground and VEE.
Where can I download the LM2904DG datasheet PDF?
The LM2904DG datasheet PDF is available from the official onsemi document link listed on this page. The manufacturer datasheet is the primary document for the complete pin description, electrical limits, typical characteristics, recommended operating conditions, and application guidance. Use the LM2904-D document because the DG ordering code is an 8-pin SOIC version of that device family.
Where can I find the LM2904DG pinout?
The LM2904DG uses an 8-pin SOIC footprint, with two complete operational amplifiers and shared supply pins. According to the onsemi manufacturer datasheet, pins 1 through 3 form the first amplifier, pins 5 through 7 form the second amplifier, pin 4 is VEE, and pin 8 is the positive supply. Confirm the named signals against the datasheet before assigning PCB nets.
Is LM2904DG suitable for single 5V operation?
Yes, the LM2904DG is suitable for a single 5 V supply because its specified operating range begins at 3 V. According to the onsemi manufacturer datasheet, the common-mode input range extends to ground, which improves usefulness in battery and sensor systems. Check the required output swing, input common-mode range, and load requirements for the specific circuit.
What can replace LM2904DG?
The LM2904DG can be replaced by compatible LM2904-family devices that use the same 8-pin SOIC footprint and remain within the required voltage, bandwidth, slew-rate, and offset limits. Candidate drop-in devices include TI LM2904BIDR and STMicroelectronics LM2904AYDT. Verify the exact pin arrangement and worst-case electrical limits against the manufacturer datasheet before substitution.
What is the best drop-in replacement for LM2904DG?
TI LM2904BIDR is a leading drop-in candidate because it is identified as an 8-pin SOIC LM2904-family device with comparable general-purpose behavior. The onsemi manufacturer datasheet lists the LM2904DG at 1 MHz gain-bandwidth product, 3 V to 32 V supply, and 0.6 V/us slew rate. Confirm offset voltage, common-mode limits, and temperature grade at the completed BOM level.
LM2904DG vs LM2904BIDR - which is better for a 12V industrial control circuit?
LM2904BIDR may be preferable when a standardized, pin-compatible LM2904-family supply chain is required, while LM2904DG offers a 3 V to 32 V supply range and 1 MHz gain-bandwidth product. According to the onsemi manufacturer datasheet, LM2904DG also specifies 0.6 V/us slew rate and a 7 mV input offset voltage. Compare the candidate's guaranteed limits before deciding.
What is the difference between LM2904DG and LM2904B?
LM2904B is an improved LM2904-family option rather than a functionally unrelated amplifier. The onsemi LM2904DG has a listed 1 MHz gain-bandwidth product and 7 mV input offset voltage, while LM2904B-family documentation is associated with improved performance. Both can use the same 8-pin SOIC footprint when their exact ordering codes and electrical limits are confirmed.
When should I choose LM2904DG over a precision op amp?
Choose LM2904DG when the circuit needs two general-purpose amplifier channels, a 3 V to 32 V supply range, and adequate speed for moderate-frequency analog signals. Its 7 mV input offset voltage and 50 dB minimum CMRR are not ideal for precision bridge measurement or sub-microvolt instrumentation. Use a low-offset, high-CMRR amplifier when those errors dominate the measurement.
Is LM2904DG suitable for sensor signal conditioning?
The LM2904DG is suitable for moderate-accuracy sensor conditioning when signals stay within its input common-mode range and the required bandwidth is below 1 MHz. According to the onsemi manufacturer datasheet, it can operate from 3 V to 32 V and its common-mode input range extends toward ground. Add filtering and offset correction when the sensor produces signals below the practical input range.
Where to buy LM2904DG online?
Use the Request a Quote form on this page to request LM2904DG availability, current pricing, minimum order quantity, and lead time. The structured pricing section reflects qualifying exact-MPN listings when quantity-break data is available. For a production BOM, request the manufacturer ordering code, package suffix, and delivery requirements together.
What is the price of LM2904DG?
Current LM2904DG pricing is shown through the Request a Quote form on this page, allowing buyers to request the quantity required without relying on a static price. The distributor listing identifies the exact LM2904DG ordering code and an 8-pin SOIC package. Volume, delivery timing, and supply status can affect the final quotation.
What is the lead time for LM2904DG?
Request the current LM2904DG lead time through the Request a Quote form on this page, including your required quantity, target shipment date, and acceptable package configuration. Lead time depends on inventory, factory scheduling, and order volume. Planning the request around a specific production milestone helps the distributor confirm a realistic delivery commitment.
Is LM2904DG in stock?
Current LM2904DG stock status is best confirmed through the Request a Quote form on this page. The distributor listing identifies the exact 8-pin SOIC part, but availability can change with order volume and replenishment cycles. Include your required quantity and target date so the response reflects the appropriate production supply.
What is the best STMicroelectronics equivalent for LM2904DG?
STMicroelectronics LM2904AYDT is a cross-brand candidate for LM2904DG because it is identified as a dual general-purpose LM2904-family amplifier in an 8-pin SOIC package. The onsemi LM2904DG operates from 3 V to 32 V with a 1 MHz gain-bandwidth product and 0.6 V/us slew rate. Confirm the ST device's guaranteed limits and pin mapping before production use.

داتای سەرچاوەی ئەندازیاری بۆ LM2904DG — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LM2904DG when the design requires two general-purpose amplifier channels, operation across a 3 V to 32 V supply range, and approximately 1 MHz gain-bandwidth in an 8-pin SOIC. It is a practical fit for industrial sensor conditioning, low-frequency active filters, audio preamplification, and basic feedback-control loops. Choose onsemi LM2904B when its improved offset characteristics are important and the exact ordering code meets the supply and temperature requirements. Choose TI LM2904BIDR when procurement standardization is more important, accepting that the listed TI LM2904-family bandwidth of 700 kHz is 30% below the LM2904DG value. Choose plain TI LM2904 only when its 26 V maximum supply is sufficient. Choose STMicroelectronics LM2904AYDT for a second-source 8-pin SOIC option after checking its guaranteed offset, temperature, bandwidth, and common-mode limits. For rail-to-rail output, microvolt-level offset, or substantially greater bandwidth, move to a specialized amplifier family.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2904B LM2904BIDR LM2904 LM2904AYDT
Brand onsemi onsemi Texas Instruments Texas Instruments STMicroelectronics
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Number of Channels 2 channels 2 channels 2 channels 2 channels 2 channels
Amplifier Type General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier
Supply Configuration Single supply or split supply Single supply or split supply Single supply or split supply Single supply or split supply Single supply or split supply

جیاکەرەوە سەرەکییەکان

  • Higher listed gain-bandwidth product than the standard TI LM2904-family device (بەراورد بەLM2904)
  • Wider maximum supply-voltage rating (بەراورد بەLM2904)
  • Same 8-pin SOIC replacement route with a documented LM2904-family identity (بەراورد بەLM2904AYDT)

تێبینییەکانی دیزاین

Use a local bypass capacitor from each supply pin to ground and place it directly beside the SOIC. Keep the return path short so switching current does not share a long trace with the analog signal. Because the LM2904DG accepts a 3 V to 32 V supply, verify headroom for the selected operating point rather than designing only from the maximum rating. Confirm the device's quiescent current and output-current limits from the manufacturer datasheet before finalizing the power budget.

Do not assume that the full 0 V to V+ output range is available. The input common-mode range extends toward ground, but output swing, input bias, offset voltage, and load capability impose separate limits. At low supply voltages, verify the minimum operating voltage under the actual load and temperature. For single-supply operation, provide an appropriate bias reference or AC coupling when the input source cannot produce a signal below the usable common-mode range.

Route each amplifier's feedback components close to the corresponding output and inverting-input pins. Keep input traces away from the supply-pin bypass connection and from switching nodes. The two amplifier channels are independent, but sharing the same package makes it convenient to isolate noisy digital or power circuitry on the opposite side of the board. Maintain a continuous ground reference under the device where the PCB layout permits.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The exact LM2904DG listing does not explicitly state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not stated for this ordering code and is therefore not applicable.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2904DG LM2904DG datasheet LM2904DG datasheet pdf LM2904DG pinout LM2904DG equivalent LM2904DG replacement LM2904DG cross reference onsemi LM2904DG LM2904DG 8-SOIC LM2904DG 1MHz op amp LM2904DG 3-32V amplifier LM2904DG sensor signal conditioning LM2904DG vs LM2904BIDR LM2904DG price LM2904DG stock

پێکهاتە و زاراوە پەیوەندیدارەکان

onsemi LM2904DG LM2904B LM2904BIDR LM2904 LM2904AYDT operational amplifier dual amplifier general-purpose amplifier analog signal conditioner semiconductor 1 MHz gain-bandwidth product 0.6 V/us slew rate 3 V to 32 V supply voltage 7 mV input offset voltage 50 dB common-mode rejection ratio single-supply operation split-supply operation common-mode input voltage range SOIC-8 surface-mount package active filter sensor interface feedback control
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ