LM358DRG4 - Dual 700 kHz Op Amp | Texas Instruments
MPN: LM358DRG4 ✓ چالاکLM358DRG4 گشتی
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM358 belongs to the dual operational-amplifier family, combining two amplifier channels in one IC. Its common-mode input range extends toward ground, making it useful in single-supply designs where signals remain close to the lower supply rail. It can also operate from split supplies for circuits that require positive and negative output swings.
The two amplifiers are designed for general-purpose signal conditioning rather than precision-null or rail-to-rail performance. Internal frequency compensation removes the need for an external compensation network in typical closed-loop configurations. The 700 kHz gain-bandwidth product supports useful bandwidth at moderate closed-loop gains, while the 0.3 V/µs slew rate helps preserve large-signal response. Separate input, output, and supply pins give each channel independent signal-path routing.
The LM358 architecture includes an input stage capable of operating with the output near the negative supply rail and output stages designed for capacitive-load drive. Because the output stage operates in a push-pull configuration, the device can source and sink output current, but ground currents associated with load current can affect source-to-source offset in some circuit configurations. Review the datasheet test conditions and application guidance before using the amplifier in precision measurement paths.
Typical uses include audio preamplifiers, active filters, sensor-conditioning circuits, low-voltage control loops, and general instrumentation. The device is especially suitable for battery-powered and single-supply systems where input signals remain above ground, although input common-mode and output-swing limits still determine usable signal range. Two channels can implement independent gain stages, buffer a sensor and condition its output, or form the active elements in a multi-stage filter.
For layout, keep input and feedback traces short, connect decoupling capacitors close to the supply pins, and avoid routing output traces near high-impedance input nodes. A common single-supply design uses ground as the reference at pin 4, decouples the positive rail at pin 8, and biases the non-inverting inputs above ground. Output saturation, input common-mode limits, load capacitance, and stability must all be checked during design review.
This product overview combines the exact ordering, package, electrical, and packaging information for LM358DRG4 with practical guidance on single-supply operation, PCB implementation, application selection, and verified drop-in alternatives. It is intended to help engineers identify the correct amplifier, interpret its constraints, and plan a production-ready replacement strategy without relying on generic LM358 guidance.
جێگرەوەکانی جێگۆڕکێ بۆ LM358DRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358DRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Number of Amplifiers, Mounting Type, Common-Mode Input Range.
LM358DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM358DE4
✅ جێگرەوەی ڕاستەوخۆ✓ بەردەستە
$1.3125 / یەکە
بینینی داتاشیت →LM358N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NCV2904DR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →RC4558
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM358DRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | General Purpose |
| Number of Circuits | 2 |
| Number of Amplifiers | 2 |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Supply Voltage Range | ±1.5 V to ±16 V |
| پاکێج | 8-SOIC |
| ژمارەی پین | 8 |
| جۆری دامەزراندن | Surface Mount |
| Packaging | Tape & Reel (TR) |
ڕێکخستنی پینی LM358DRG4
| پین 1 | OUTA — Output of amplifier A |
| پین 2 | IN A- — Inverting input of amplifier A |
| پین 3 | IN A+ — Non-inverting input of amplifier A |
| پین 4 | V- — Negative supply or ground connection |
| پین 5 | IN B+ — Non-inverting input of amplifier B |
| پین 6 | IN B- — Inverting input of amplifier B |
| پین 7 | OUTB — Output of amplifier B |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
LM358DRG4 گونجاوە بۆ 6 بەکارھێنانs: Active Audio Filters, Sensor Signal Conditioning, Battery-Powered Control Loops, Instrumentation and Measurement Front Ends, Power-Supply Feedback and Monitoring, Interface and Level Shifting.
Active Audio Filters
The LM358DRG4 suits active audio filters requiring two independent amplifier channels in one 8-SOIC package. Its 700 kHz gain-bandwidth product provides useful closed-loop bandwidth for low-frequency response shaping, while the 0.3 V/µs slew rate supports ordinary audio-rate signals. The device can implement first- or second-order stages in a non-inverting or inverting topology, subject to the datasheet’s stability and output-loading guidance. Two amplifiers can also form a state-variable filter section when component tolerances and gain-bandwidth ratios are controlled. The principal limitation is the LM358’s non-rail-to-rail input and output behavior, so headroom must be reserved around filter signals, especially on a single low-voltage supply.
پێشنیارکراو
Sensor Signal Conditioning
The LM358DRG4 is useful for conditioning moderate-voltage sensor outputs when the signal can remain within the amplifier’s common-mode input range. One channel can amplify a sensor signal while the other provides buffering or an active level shift, and the 0.3 V/µs slew rate is ample for many temperature, position, and light-sensor bandwidths. On a 3.3 V or 5 V single supply, biasing the non-inverting input above ground allows operation around signals that would otherwise approach the lower rail. Confirm that input bias current, offset voltage, and common-mode limits meet the sensor’s accuracy requirements. A high-impedance sensor may also require guarding to reduce leakage and surface contamination effects.
پێشنیارکراو
Battery-Powered Control Loops
The LM358DRG4 fits low-voltage control and monitoring loops that use a 3 V to 5 V supply and keep the operating point above ground. Its two channels support common tasks such as error amplification and actuator drive, with a 700 kHz gain-bandwidth product allowing closed-loop response well beyond basic low-speed regulation. The split-supply capability also permits use in circuits that need a bipolar output reference. Designers should verify the output-current capability, output swing, and stability into the actual load. Because the amplifier’s quiescent current is part of total battery budget, evaluate it against the selected operating mode and compare it with rail-to-rail alternatives when energy efficiency is the dominant priority.
پێشنیارکراو
Instrumentation and Measurement Front Ends
The LM358DRG4 can provide gain and buffering stages in conventional instrumentation where the signal remains inside its common-mode range. Two channels permit a balanced signal to be amplified and then filtered, or a sensor output to be buffered before conversion. The 700 kHz bandwidth supports many low- and mid-frequency instrumentation applications, and the 0.3 V/µs slew rate accommodates signals requiring substantially more bandwidth than precision DC measurement alone would imply. For instrumentation-grade accuracy, check input offset voltage, input bias current, drift, and noise against the measurement specification. These characteristics are as important as bandwidth when the signal is small and the system must reject offset-generated error.
پێشنیارکراو
Power-Supply Feedback and Monitoring
The LM358DRG4 is appropriate for low-bandwidth power-supply feedback, error amplification, and output-monitoring functions where the measured node lies within its input and output operating ranges. One amplifier can amplify the difference between a feedback divider and a reference, while the second can monitor the output condition. The device’s tolerance of split supplies and single supplies from 3 V upward supports both traditional bipolar control circuits and compact low-voltage systems. Confirm loop stability, output-current behavior, and the minimum gain-bandwidth ratio required by the compensation network. It is best suited to slow or moderate feedback loops rather than systems requiring the response of a dedicated high-speed voltage-mode controller.
پێشنیارکراو
Interface and Level Shifting
The LM358DRG4 can serve as an interface buffer when the source and destination share a suitable common reference. Its common-mode range extending toward ground is useful in single-supply systems, where the amplifier can process signals close to the lower rail when the inputs are appropriately biased. The two channels can buffer two related signals, such as a sensor output and a control return. The 8-SOIC package is convenient for automated assembly and provides a straightforward pin arrangement for routing. Before using the device as a digital logic-level translator, verify the input thresholds, output levels, source and sink capability, and propagation behavior; these specifications differ from a dedicated logic translator and must be checked against the connected device.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM358DRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM358DR | LM358DE4 | LM358N | NCV2904DR2G | RC4558 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | YAGEO |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Amplifier Configuration | Dual | Dual | Dual | Dual | Dual | Dual |
| Amplifier Type | General Purpose | General Purpose | General Purpose | General Purpose | General Purpose | General Purpose |
| Number of Circuits | 2 | 2 | 2 | 2 | 2 | 2 |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount | Surface Mount | Surface Mount | Surface Mount |
جیاکەرەوە سەرەکییەکان
- Established dual general-purpose architecture (بەراورد بەRC4558)
- Single-supply operation from the lower specified limit (بەراورد بەNCV2904DR2G)
- Orderable surface-mount tape-and-reel configuration (بەراورد بەLM358DE4)
تێبینییەکانی دیزاین
Place the positive-supply bypass capacitor directly between pins 8 and 4, with the ground end connected to the shortest return path available. Keep the amplifier’s output and feedback routing away from sensitive input nodes, and connect the ground reference of each amplifier section to the same low-impedance ground plane region. In single-supply designs, establish the signal reference carefully because output and input limits relative to ground determine usable swing.
Do not assume the LM358 input range reaches either supply rail or that its output can swing rail to rail. Check the datasheet’s common-mode and output-voltage limits at the intended supply voltage, then reserve sufficient headroom for the signal and feedback network. When driving a capacitive load, confirm stability; excessive output capacitance or incorrect compensation can cause oscillation. Also verify source and sink current for the selected load rather than relying on the nominal amplifier category.
For low-frequency precision applications, evaluate input bias current and offset-voltage error rather than bandwidth alone. Use practical PCB techniques to limit leakage around high-impedance inputs, including clean surfaces, guarding, and short traces. For higher-frequency signals, preserve feedback-loop compactness, minimize parasitic capacitance, and verify the gain-bandwidth ratio and phase margin required by the selected topology. The 700 kHz gain-bandwidth product does not by itself guarantee closed-loop stability for every noise gain.
Estimated: at a 16 V single supply, 8 V output, and 10 mA output load, the estimated internal dissipation is 80 mW using P = (VIN − VOUT) × IOUT. This is well below the power level normally expected to require substantial heatsinking, but verify the actual output stage dissipation, load, and ambient temperature over the full operating range. Keep copper connected to the exposed ground path used by the package and follow the manufacturer’s soldering and reflow guidance.
زانیاری پابەندبوون
No explicit RoHS, REACH, halogen-free, lead-free, or conflict-minerals statement appears in the cited component records. AEC-Q100 is not applicable because this is a general-purpose operational amplifier rather than an automotive-qualified device.