LM358DR2G - Dual 3-32V Op Amp, 1MHz, 8-SOIC | onsemi
MPN: LM358DR2G ✓ چالاکLM358DR2G گشتی
A dual operational amplifier is a semiconductor containing two independent high-gain amplifier sections with internal frequency compensation. Within the broader IC hierarchy, it belongs to the operational amplifier family, which sits inside analog and amplifier ICs. The LM358 series is functionally similar to one half of a quad LM324, with the common-mode input range extending toward the VEE rail to simplify single-supply interfacing to sensors whose outputs remain close to 0 V.
Principal electrical characteristics include a 3 V to 32 V operating supply range, a 1 MHz gain-bandwidth product, two amplifier circuits per package, and operation from a common ground or negative supply. The low power drain of the circuit designs from which the LM358 series was derived supports low-power industrial and instrumentation systems. The wide supply range allows the same amplifier topology to operate from regulated 5 V rails or directly from higher nominal industrial supply voltages, subject to the device ratings and local regulations.
The LM358DR2G uses an internally compensated architecture with two independent channels. Internal compensation eliminates the need for an external dominant-pole capacitor in the basic non-inverting and inverting configurations, simplifying analog design and reducing component count. The common-mode input voltage range extending to ground makes the amplifier useful in battery monitoring, current-sense amplifiers, transducers, and interfaces whose signals do not swing far above the negative rail.
Typical applications include 5 V and 24 V sensor-signal conditioning, low-side current sensing, audio preamplification, buffer stages, comparators with open-collector outputs, and general industrial control. Because both amplifiers share the same package and supply pins, the device can implement two independent stages or be configured as one differential amplifier using the second channel for feedback. The 8-SOIC package also supports automated assembly and is widely supported by standard analog design tools.
When designing around the LM358DR2G, verify output-current capability for the selected load, especially when driving capacitive inputs, and check common-mode limits at the actual supply voltage. Place bypass capacitors close to the supply pins and route feedback and input traces away from switching nodes. This page combines manufacturer electrical characteristics, source traceability, drop-in alternatives, package details, and application-level engineering guidance for faster component selection.
جێگرەوەکانی جێگۆڕکێ بۆ LM358DR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358DR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Number of Amplifiers, Mounting Type, Slew Rate.
LM358DRG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM358DR
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM358D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM358ADR2G
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM358N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →RC4558
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM358DR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifiers | 2 channels |
| ڤۆڵتاژی دابینکردنی کارکردن | 3 V to 32 V |
| Gain-Bandwidth Product | 1 MHz |
| Amplifier Type | Standard general-purpose operational amplifier |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Supply Configuration | Single supply or split supply |
| Common-Mode Input Range | Extends to ground/VEE |
| Compensation | Internally compensated |
ڕێکخستنی پینی LM358DR2G
| پین 1 | OUT1 — Amplifier 1 output |
| پین 2 | IN1- — Amplifier 1 inverting input |
| پین 3 | IN1+ — Amplifier 1 non-inverting input |
| پین 4 | V- — Negative supply or ground connection |
| پین 5 | IN2+ — Amplifier 2 non-inverting input |
| پین 6 | IN2- — Amplifier 2 inverting input |
| پین 7 | OUT2 — Amplifier 2 output |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
LM358DR2G گونجاوە بۆ 6 بەکارھێنانs: Low-Side Current-Sense Amplification, Industrial Sensor Signal Conditioning, Audio Preamplifier and Buffer Stage, Power-Supply Feedback and Control Loops, Single-Supply Comparator with Open-Collector Output, Battery and Portable-System Monitoring.
Low-Side Current-Sense Amplification
The LM358DR2G suits low-side shunt amplification because it operates from 3 V to 32 V and its common-mode input range extends toward ground/VEE. Place it near the shunt resistor so the millivolt-scale differential signal does not traverse a long, noisy board path. The 1 MHz gain-bandwidth product supports practical closed-loop gains in typical current-monitor circuits. Check that the common-mode voltage stays inside the amplifier's operating range at the minimum supply voltage, and verify that the output does not saturate at the maximum expected load current.
پێشنیارکراو
Industrial Sensor Signal Conditioning
The LM358DR2G is appropriate for conditioning resistive, resistive-bridge-derived, or buffered sensor signals in 24 V industrial control systems. Its single-supply capability and common-mode range extending toward ground reduce the need for negative rails when the sensor output is near 0 V. Use one channel for amplification and the other for buffering or active filtering. The 1 MHz gain-bandwidth product is more than adequate for many temperature, level, and position sensors, although sensor bandwidth and long cable noise must be considered separately.
پێشنیارکراو
Audio Preamplifier and Buffer Stage
The LM358DR2G can provide gain and buffering in modest audio preamplifier paths because its 1 MHz gain-bandwidth product covers the midband requirements of many line-level and low-level audio circuits. The common-mode input range extending toward ground is useful in single-supply mixer designs, and the internal compensation simplifies conventional feedback layouts. Place input and feedback resistors close to the amplifier, maintain return paths away from switching converters, and verify output swing and loading against the intended speaker driver or audio load.
پێشنیارکراو
Power-Supply Feedback and Control Loops
The LM358DR2G is useful as an error amplifier or buffer in linear power-control loops where a 1 MHz gain-bandwidth product provides adequate loop bandwidth. Its 3 V to 32 V operating range allows operation from a regulated control rail or a higher industrial rail. Because this is a general-purpose rather than a precision op amp, offset voltage, bias current, and output-current capability must be checked for each loop. Compensation components should follow the manufacturer guidance, and the output must remain within the amplifier's output-swing limits.
پێشنیارکراو
Single-Supply Comparator with Open-Collector Output
The LM358DR2G can be configured as an open-collector comparator in single-supply systems, using the output transistor to drive a pull-up resistor and indicating when an input crosses a reference. The common-mode input range extending toward ground allows sensing of low-level signals, and the 3 V minimum supply supports compact control systems. Choose resistor values that limit output-transistor current, add deliberate hysteresis to prevent oscillation at the threshold, and account for the propagation delay introduced by the 1 MHz gain-bandwidth product.
پێشنیارکراو
Battery and Portable-System Monitoring
The LM358DR2G fits battery-monitor and portable-instrument circuits that operate from a single supply, benefiting from operation down to 3 V and a common-mode input range that extends toward ground. It can monitor a divided cell voltage, amplify a shunt signal, or buffer an analog sensor into an ADC. Because its quiescent current is not specified in the source material, battery-life calculations should use the manufacturer power-consumption data. Also verify that the selected amplifier remains valid over the full cell-voltage range and temperature extremes of the product.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM358DR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM358DRG4 | LM358DR | LM358D | LM358ADR2G | LM358N |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz |
| Common-Mode Input Range | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE | Extends to ground/VEE |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
| Compensation | Internal | Internal | Internal | Internal | Internal | Internal |
جیاکەرەوە سەرەکییەکان
- Direct onsemi LM358 family substitution path (بەراورد بەLM358DRG4)
- Wide supply operation in the standard 8-SOIC footprint (بەراورد بەLM358N)
- Two compensated amplifiers in one compact package (بەراورد بەRC4558)
تێبینییەکانی دیزاین
Place the supply bypass capacitor close to pin 8 and provide a low-impedance return at pin 4. Route the two input signals and their feedback components as short traces, especially for the LM358DR2G because its 1 MHz gain-bandwidth product couples PCB capacitance into loop stability. Keep the SOIC ground connection on the same solid ground plane used by the analog source and avoid routing beneath long switching-current paths.
Do not assume rail-to-rail input or output behavior. Although the common-mode input range extends toward ground/VEE, usable headroom depends on the supply voltage, output loading, and channel temperature. Verify minimum supply voltage, common-mode limits, output swing, and capacitive-load drive in the manufacturer datasheet before committing the schematic. Add intentional hysteresis when the device is used as a comparator.
For sensor inputs longer than a few centimeters, place the LM358DR2G near the source or protect the input with an appropriate low-pass filter. A common-mode input range extending toward ground is valuable with single-supply sensors, but it does not eliminate cable pickup. Keep the two channels in the same package electrically compatible, yet separate high-impedance input routing from switching nodes and mains-derived circuitry.
زانیاری پابەندبوون
Compliance results differ across onsemi ordering suffixes. Request current material-compliance and qualification documentation for the exact LM358DR2G orderable part through the Request a Quote form.