MC3486DG4 - Quad RS-422/423 Receiver | Texas Instruments
MPN: MC3486DG4 ✓ چالاکMC3486DG4 گشتی
A differential line receiver is an interface IC that converts a balanced differential signal arriving over a cable into a logic-level output for a digital system. The MC3486 belongs to the receiver category within the broader line-driver and transceiver hierarchy. Its four independent channels allow one device to terminate and decode four differential inputs, reducing component count in multi-channel data acquisition, industrial control, and communications equipment.
The principal features include four receiver channels, three-state outputs, TTL-compatible signaling, and operation from a nominal 5 V supply. The listed maximum receive delay is 35 ns, making the device suitable for systems that require rapid recovery of differential data from balanced lines. Its commercial temperature grade extends from 0 °C to 70 °C, while the 16-SOIC package supports conventional surface-mount PCB assembly.
Each receiver channel uses differential input signaling to reject common-mode voltage present on cabling and grounding environments. Three-state outputs permit the output pins to enter a high-impedance state when the system needs to share a data bus or isolate a receiver. The MC3486 therefore combines standard RS-422 and RS-423 reception with bus-oriented output control rather than functioning as a simple single-ended logic receiver.
Typical applications include industrial serial interfaces, test and measurement systems, data acquisition equipment, and legacy computer peripherals that communicate over balanced differential lines. Four channels make the device especially useful where multiple cable-connected sensors, controllers, or peripheral boards must feed a common digital processor. The 5 V operating range also allows the receiver to operate alongside conventional TTL and CMOS interface logic when appropriate voltage compatibility is maintained.
Designers should verify receiver enable and output-state timing against the system clock, preserve adequate differential signal margin at the cable interface, and account for connector and cable characteristics. The 35 ns maximum receive delay is a useful timing boundary when calculating setup-and-hold margins or supporting legacy peripheral clocking. Decoupling should follow the connection recommendations in the manufacturer datasheet.
This product page combines the device architecture, interface standards, timing information, verified drop-in candidates, package considerations, and practical application guidance. It also distinguishes confirmed replacement options from parts that require additional qualification, helping engineers narrow a design without confusing protocol compatibility with complete production suitability.
جێگرەوەکانی جێگۆڕکێ بۆ MC3486DG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MC3486DG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Operating Temperature Range, Output Type, Package.
MC3486DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MC3486D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DS3486M
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DS3486MX
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MC3486DG4 تایبەتمەندییەکان
| Receiver Type | Quadruple differential line receiver |
| Number of Receivers | 4 |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| Supported Protocols | RS-422 and RS-423 |
| ANSI Standard | TIA/EIA-422-B and TIA/EIA-423-B |
| ITU Recommendations | V.10 and V.11 |
| Maximum Receive Delay | 35 ns |
| جۆری دەرچوون | 3-state, TTL-compatible |
| پاکێج | 16-pin SOIC, 3.90 mm width |
| جۆری دامەزراندن | Surface mount |
| مەودای پلەی گەرمیی کارکردن | 0 °C to 70 °C |
| Packaging | Tube |
ڕێنمایی ڕێکخستنی پینی MC3486DG4 16-pin soic, 3.90 mm width
ڕێکخستنی پین بۆ MC3486DG4 (پاکێجی 16-pin soic, 3.90 mm width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MC3486DG4.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MC3486DG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Differential Data Acquisition, Test and Measurement Instrumentation, Legacy Peripheral Communications, Multi-Channel Sensor Interface, Process Control Communication Interfaces, Communication Backplane and Bus Isolation.
Industrial Differential Data Acquisition
The MC3486DG4 fits acquisition systems that must convert four balanced cable connections into digital logic signals for a controller or processor. Its four independent differential receiver channels reduce the number of separate receiver packages, while the 4.75 V to 5.25 V supply range supports conventional 5 V interface electronics. The receiver architecture targets ANSI TIA/EIA-422-B and TIA/EIA-423-B signaling, including ITU V.10 and V.11 recommendations. Because the maximum receive delay is 35 ns, timing analysis should include the complete input path rather than relying only on nominal propagation delay. Cable termination, common-mode conditions, and protection devices must be selected for the installation environment.
پێشنیارکراو
Test and Measurement Instrumentation
Instrumentation with several remote probes or fixture modules can use the MC3486DG4 to receive four balanced signals through a shared interface IC. The device converts differential RS-422 or RS-423 inputs into TTL-compatible outputs, allowing a measurement controller to read multiple channels through a defined interface standard. Its 35 ns maximum receive delay provides a concrete timing limit for synchronizing returned data with acquisition logic. Three-state outputs add flexibility when multiple interface sections must be isolated or share a bus. The 0 °C to 70 °C commercial temperature range suits controlled laboratory and production-test environments where full automotive temperature coverage is unnecessary.
پێشنیارکراو
Legacy Peripheral Communications
The MC3486DG4 is appropriate for legacy computer peripherals and industrial controllers that use balanced differential communications instead of single-ended logic. Four receiver sections can decode status, command acknowledgment, data, and control lines from one 16-SOIC package. Compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 makes it useful when the equipment interface is based on established balanced-line recommendations. The TTL-compatible outputs can interface with suitable 5 V digital logic, but designers must verify input thresholds, enable polarity, and timing in the connected legacy system. Cable routing, grounding, and termination remain essential to reliable reception.
پێشنیارکراو
Multi-Channel Sensor Interface
A sensor interface requiring several differential readings can place the MC3486DG4 between remote sensor lines and a digital acquisition controller. Four balanced inputs reduce package count compared with four single-channel receivers, while differential reception helps reject common-mode voltage present in industrial wiring. The nominal 5 V operation and TTL-compatible outputs align with many legacy control boards, while the 35 ns receive-delay ceiling helps define setup and hold margins. This use requires the engineer to verify that sensor signal amplitudes, common-mode limits, and bandwidth remain within the receiver electrical characteristics. Protection, termination, and isolation should also be evaluated for cable-connected sensors.
پێشنیارکراو
Process Control Communication Interfaces
Process-control equipment often distributes data between controllers, remote I/O, and operator panels over balanced wiring. The MC3486DG4 can receive four differential signals simultaneously, providing a compact interface between those remote nodes and a 5 V control processor. Its support for both RS-422 and RS-423 is useful where equipment uses the two related standards, while three-state outputs can assist with controlled bus isolation. The commercial temperature grade of 0 °C to 70 °C fits ordinary indoor control cabinets. System designers should account for the stated 35 ns receive delay, enable timing, cable characteristics, and any grounding or surge-protection requirements in the installation environment.
پێشنیارکراو
Communication Backplane and Bus Isolation
The MC3486DG4 can serve backplane systems that need several differential inputs with controllable output states. Its three-state outputs permit a receiver to be disconnected electrically when it is not selected, which is valuable when several interface sections share routing or when a system requires controlled isolation during reset. Four receiver channels and a 16-SOIC package provide moderate board-area savings over discrete implementations. The receiver supports ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 signaling, but the complete backplane must preserve the required differential impedance, termination, and signal integrity. Timing around enable and output-disable transitions should be checked at the system level.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MC3486DG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MC3486DR | MC3486D | DS3486M | DS3486MX |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Number of Receivers | 4 | 4 | 4 | 4 | 4 |
| Number of Drivers | 0 | 0 | 0 | 0 | 0 |
جیاکەرەوە سەرەکییەکان
- Four differential receivers in one package (بەراورد بەMC1489NG4)
- Direct documented 16-SOIC replacement path (بەراورد بەMC3486DR)
- Support for both RS-422 and RS-423 (بەراورد بەMC3487DE4)
- Defined maximum receive delay (بەراورد بەMC3486D)
تێبینییەکانی دیزاین
Do not treat RS-422 and RS-423 as interchangeable cable arrangements without checking the complete interface. The MC3486DG4 supports both signaling standards, but input thresholds, common-mode limits, termination, cable topology, and timing must satisfy the standard used by the connected equipment. Review the manufacturer input-output table and recommended interface circuit before fixing termination values or connector wiring.
Keep each differential input pair routed with continuous impedance and minimize the area between the two conductors. Route the pairs away from noisy switching nodes and maintain a stable reference plane beneath the interface. Place protection and termination components close to the connector when transient exposure is possible, while observing the receive-delay and signal-integrity margins required by the connected equipment.
Use the stated 35 ns maximum receive delay as one input to the system timing budget. Include connector, cable, protection-device, and receiver tolerances when calculating setup and hold time. The three-state outputs require a deliberate enable strategy: inactive receivers should remain in a defined state so bus contention or unintended leakage cannot affect connected logic.
Operate the receiver from a supply within the specified 4.75 V to 5.25 V range and follow the manufacturer decoupling recommendations. Keep the supply return path short and use a quiet return for the interface section, especially when nearby circuitry contains switching converters. Confirm that 5 V rail tolerance, startup behavior, and noise do not move the actual supply outside the receiver limits.
زانیاری پابەندبوون
The component is a commercial-temperature interface IC, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was established for this exact suffix. Compliance should be confirmed with the manufacturer or current environmental documentation.