Texas Instruments

OPA137UA - 36V, 1MHz FET-Input Op Amp | Texas Instruments

MPN: OPA137UA ✓ Active
36 V Vdss ±10 pA Id 8-SOIC, 0.154 in (3.90 mm) width Package
MOQ: 1 |

OPA137UA Overview

The Texas Instruments OPA137UA is a single, 36 V, 1 MHz FET-input operational amplifier with rail-to-rail input operation to the positive supply, low input bias current, and low power consumption. It is packaged in an 8-pin SOIC and is intended for precision signal conditioning, instrumentation, sensor interfaces, and low-noise analog systems. The low-bias input stage supports source impedances that would challenge conventional bipolar input amplifiers.

A FET-input operational amplifier is an operational amplifier that uses field-effect transistors at its input. This input architecture provides very low bias current and high input impedance while preserving the voltage-feedback behavior expected by standard analog signal chains. The OPA137 belongs to the broader hierarchy of operational amplifier, analog amplifier, and semiconductor components used for amplification, filtering, buffering, and instrumentation.

Key characteristics include a 1 MHz gain-bandwidth product, ±10 pA typical input bias current, 120 µA typical quiescent current per channel, and 145 dB typical open-loop gain. Its input common-mode range extends to the positive supply, making the device practical in single-supply systems where the signal can approach the upper rail. The listed JLCPCB record also identifies 1.5 mV offset, 15 µV/°C temperature drift, 3.5 V/µs slew rate, 76 dB channel-separation behavior, and approximately 5 pA bias current for this ordering option.

The JFET input stage provides a practical balance between low noise, very high input impedance, and low supply current. Unlike bipolar-input operational amplifiers, it does not require substantial input bias current to operate. Its 1 MHz bandwidth is appropriate for audio-frequency measurement, transducers, and general-purpose precision analog signal chains, although it is not intended for high-speed video or RF signal paths. The 36 V maximum supply rating also allows operation from substantially higher rails than typical low-voltage amplifier families.

Typical uses include low-leakage current measurement, pH and electrochemical sensing, photodiode and other high-impedance sensor interfaces, precision filtering, and industrial instrumentation. In these applications, the OPA137UA can reduce loading of the sensor while preserving a 1 MHz signal bandwidth. It can also serve as a unity-gain buffer when the source presents limited DC bias current.

Layout should keep the input traces short and guard sensitive nodes from leakage and capacitive pickup. Place the bypass capacitor close to the positive-supply pin, maintain a low-impedance ground return, and provide adequate copper around the SOIC for stable thermal performance. Because the device is intended for low-bias operation, board contamination, flux residue, and moisture around high-impedance inputs can materially degrade practical input bias performance.

This product page combines the manufacturer specifications with package, application, lifecycle, sourcing, and drop-in replacement guidance. The comparison and design notes clarify where the OPA137UA is appropriate, what parameters matter when substituting an amplifier, and which circuit-level issues should be checked before production release.

Drop-in alternatives for OPA137UA — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with OPA137UA (same form factor and footprint) — differing in Package, Gain-Bandwidth Product, Amplifier Type, Input Bias Current, Input Common-Mode Range.

Texas Instruments
Package: 8-SOIC, 0.154 inch (3.90 mm) width
Gain-Bandwidth Product: 8 MHz
Amplifier Type: Single audio operational amplifier
Compare with OPA137UA →
Texas Instruments
Package: 8-pin PDIP
Input Bias Current: ±5 pA typical
Input Common-Mode Range: Rail-to-rail input to V+
Compare with OPA137UA →

OPA131UJ

✅ Drop-In
📦 8-SOIC
Gain-bandwidth product is approximately 1 MHz, matching the OPA137UA's 1 MHz rating; other bias-current, offset, and drift differences require comparison against the manufacturer datasheets.

📋 Reference alternative (not in catalog)

OPA137UA Maximum Ratings & Electrical Characteristics

Amplifier Type Single FET-input operational amplifier
Number of Channels 1 channel
Maximum Supply Voltage 36 V
Gain-Bandwidth Product 1 MHz
Input Common-Mode Range Rail-to-rail to the positive supply
Typical Input Bias Current ±10 pA
Listed Input Bias Current 5 pA
Typical Quiescent Current 120 µA per channel
Listed Quiescent Current 220 µA
Typical Open-Loop Gain 145 dB
Input Offset Voltage 1.5 mV
Input Offset Voltage Temperature Drift 15 µV/°C
Slew Rate 3.5 V/µs
Channel Separation 76 dB
Protection Features Short-circuit protection and ESD protection
Package 8-SOIC, 0.154 in (3.90 mm) width
RoHS Status RoHS compliant

OPA137UA Pin Configuration

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 NC — Not connected
Pin 2 IN- — Inverting input
Pin 3 IN+ — Non-inverting input
Pin 4 V- — Negative supply
Pin 5 NC — Not connected
Pin 6 OUT — Output
Pin 7 V+ — Positive supply
Pin 8 NC — Not connected

Typical Applications

OPA137UA is suitable for 6 applications: Precision pH and Electrochemical Sensing, Photodiode Signal Conditioning, Low-Leakage Current Measurement, Audio-Band Sensor Conditioning, Precision Filtering and Buffering, Industrial Instrumentation.

🧪

Precision pH and Electrochemical Sensing

The OPA137UA is appropriate for buffering electrochemical and pH-style sensors because its JFET input stage provides ±10 pA typical bias current, reducing measurement error caused by input loading. The sensor can connect near the amplifier input while the 1 MHz bandwidth preserves useful response through low-frequency sensor dynamics. Keep the high-impedance input traces short, clean, and separated from noisy power paths. A practical design should also account for input offset voltage, drift, electrode leakage, guard-ring techniques, and the output-swing limits of the selected supply voltage.

📷

Photodiode Signal Conditioning

The OPA137UA can serve as a transimpedance or input-buffer stage for photodiode signals because its low bias current avoids developing large error voltages across high-value feedback or bias resistors. Its 1 MHz bandwidth supports moderate-speed optical measurements without requiring the higher current of a conventional bipolar-input amplifier. The trade-off is that the 1.5 mV listed input offset and 15 µV/°C drift become important at high gain, so dark-current calibration and temperature compensation may be required.

⚡

Low-Leakage Current Measurement

For precision current measurement, the OPA137UA's ±10 pA typical input bias current helps prevent the amplifier input from materially altering a microampere-level or picoampere-level sensing path. Its 1 MHz bandwidth is sufficient for many laboratory and industrial monitoring loops while its rail-to-rail-to-positive input range simplifies single-supply instrumentation. Validate leakage from PCB coatings, connectors, humidity, and nearby humidity-sensitive components because practical board-level contamination can exceed the amplifier's specified input current.

🎧

Audio-Band Sensor Conditioning

The OPA137UA fits audio-frequency sensor conditioning, including microphone, audio transducer, and instrumentation preamplifier stages requiring very low input bias current. Its 1 MHz gain-bandwidth product supports signal bandwidth well beyond typical audio content, while the low quiescent current of 120 µA per channel is beneficial in portable equipment. The 36 V rating provides headroom for higher-voltage signal paths. Check capacitive-load stability and output-current requirements when driving long cables or unusually large feedback resistors.

🔧

Precision Filtering and Buffering

The OPA137UA can implement active filters and unity-gain buffers when the source presents high impedance and the circuit needs low input loading. Its 145 dB typical open-loop gain supports accurate closed-loop gain, and the 1 MHz bandwidth is adequate for low-frequency measurement filters. At high noise gain, verify the gain-bandwidth, output-swing, and capacitive-stability limits in the manufacturer datasheet. Component tolerances and leakage in the feedback network may dominate actual filter accuracy.

🏭

Industrial Instrumentation

OPA137UA is suitable for industrial measurement front ends that operate from higher supply voltages and interface with high-impedance transducers. The 36 V maximum supply rating is useful where sensor excitation and signal levels exceed low-voltage amplifier limits, while rail-to-rail input operation to the positive supply improves input-range utilization. Because industrial environments introduce leakage, humidity, surge, and EMI risks, use guarding, appropriate protection, clean board materials, and verified bypass-capacitor placement around the amplifier.

Where can I download the OPA137UA datasheet PDF?
The OPA137UA datasheet PDF is available from the official Texas Instruments product page at https://www.ti.com/lit/ds/symlink/opa137.pdf. The document covers the OPA137 single-amplifier ordering option as well as the related OPA2137 dual and OPA4137 quad devices. It describes the 36 V maximum supply, 1 MHz gain-bandwidth product, JFET-input characteristics, electrical specifications, pin configurations, and typical application information.
What are the key specifications of OPA137UA that engineers should know?
The OPA137UA is a single, 36 V, 1 MHz JFET-input operational amplifier in an 8-SOIC package. According to the Texas Instruments OPA137 datasheet, it provides ±10 pA typical input bias current, 120 µA typical quiescent current per channel, and 145 dB typical open-loop gain. Its input common-mode range reaches the positive supply rail, making it suitable for single-supply precision signal-conditioning circuits with high-impedance sources.
Where can I find the OPA137UA pinout?
The OPA137UA pinout is shown in the pin-configuration section of the Texas Instruments OPA137 datasheet. It is an 8-SOIC single-amplifier device with standard operational-amplifier connections for the two inputs, output, positive supply, negative supply, and NC pins. Use the manufacturer pin table when assigning PCB tracks, especially for the 8-SOIC footprint used by the OPA137UA.
What is the supply-voltage range of OPA137UA?
The Texas Instruments OPA137 family is rated for operation up to 36 V, making the OPA137UA suitable for industrial and bipolar supply arrangements above typical low-voltage amplifier limits. The exact operating supply range and performance limits should be confirmed in the manufacturer datasheet for the selected junction temperature and output-load conditions. The product page identifies the device as a single, 36 V operational amplifier.
Is OPA137UA suitable for high-impedance sensor interfaces?
Yes, the OPA137UA is well suited to high-impedance sensor interfaces because its JFET input stage provides ±10 pA typical input bias current. This low loading preserves the output of pH probes, electrochemical sensors, photodiodes, and other high-source-impedance transducers. Its 1 MHz gain-bandwidth product supports precision low-frequency and audio-band signal conditioning, while its rail-to-rail-to-positive input range simplifies single-supply biasing.
What can replace the OPA137UA?
A genuine replacement should use the same 8-SOIC footprint, preserve the standard single-operational-amplifier pinout, and remain within about 30% of the key 1 MHz bandwidth, 36 V supply, and low-bias-current ratings. The verified cross-reference results identify OPA131UJ as a close same-manufacturer option, but engineers should review its full electrical specifications and confirm stability with the intended feedback network. No broad set of pin-compatible alternatives is established here.
Is OPA137UA the same as OPA131UJ?
No, the OPA137UA and OPA131UJ are related JFET-input amplifiers but are not identical devices. Both are associated with approximately 1 MHz bandwidth, but their offset, drift, bias-current, supply, and load-capacitance details must be compared before substitution. OPA131UJ is presented as a pin-to-pin alternative to the 8-SOIC OPA137UA, while the exact electrical deltas remain model-specific.
OPA137UA vs OPA131UJ: which is better for a low-leakage measurement circuit?
Choose the OPA137UA when its specified input-bias and offset behavior best matches the measurement error budget; otherwise OPA131UJ may be a practical pin-compatible alternative. The OPA137UA is specified with ±10 pA typical input bias current, 1.5 mV listed offset, 15 µV/°C drift, and a 1 MHz bandwidth. The OPA131UJ should be selected only after checking its comparable bias-current, drift, noise, and overload specifications.
When should I choose OPA137UA over OPA131UJ?
Choose the OPA137UA when the circuit depends specifically on its 36 V-rated, low-bias JFET input stage and the manufacturer-published offset and drift characteristics. Consider OPA131UJ when its lower-voltage or other operating limits fit the design and its corresponding performance is adequate. Both options require verification of input/output common-mode range, output swing, stability, and load drive before being treated as drop-in replacements.
Is OPA137UA suitable for single-supply operation?
Yes, OPA137UA supports single-supply operation because its input common-mode range includes the positive supply. The positive-supply pin and negative-supply pin must still be connected according to the manufacturer pinout, with the bypass capacitor placed close to the device. Designers should confirm that the required signal and output ranges remain inside the common-mode and output-swing limits shown in the datasheet.
What is the best Texas Instruments equivalent for OPA137UA?
OPA131UJ is the closest supported same-manufacturer candidate in the cross-reference material for the 8-SOIC OPA137UA. It provides a same-package, pin-compatible path for redesigns, but equivalence does not guarantee identical AC and DC behavior. Confirm the 1 MHz-class bandwidth, input-bias current, input offset, drift, output drive, and common-mode limits against the original design requirements.
Where can I buy OPA137UA and check current availability?
Use the Request a Quote form on this page to request current OPA137UA availability, lead time, and order handling without relying on a stale static quote. The exact manufacturer ordering code is OPA137UA, and the package is 8-SOIC. Confirm the mounted-device orientation, package suffix, and quantity requirements when placing the order to avoid confusion with related OPA137 series order codes.
What is the price of OPA137UA?
Current OPA137UA commercial terms should be requested through the Request a Quote form on this page. The form is the appropriate channel for unit pricing, quantity breaks, stock status, and lead time because market conditions and component availability change. Include the required order quantity and packaging preference so the quotation reflects the exact OPA137UA ordering option.
What is the lead time and stock status for OPA137UA?
Request the current OPA137UA lead time and stock status through the Request a Quote form on this page. A Heisener listing displayed immediate-shipment inventory and an estimated delivery window at the time captured, but such availability is transient and should not be treated as a guaranteed quotation. Confirm the requested quantity, country of shipment, and date on the returned quotation.
Does OPA137UA have low-noise performance for precision instrumentation?
The OPA137UA combines JFET-input behavior with a 1 MHz gain-bandwidth product and 145 dB typical open-loop gain, making it appropriate for many precision-instrumentation stages. Its low bias current is especially valuable when the source resistance is high and input-loading error would dominate. Final noise performance still depends on source resistance, feedback resistor values, bandwidth, and the selected noise-gain configuration.
Is OPA137UA RoHS compliant?
Yes, the product record for OPA137UA identifies the amplifier as RoHS compliant. RoHS compliance concerns restrictions on specified substances in electronic equipment and does not by itself qualify a component for automotive use. For regulated applications, review the current manufacturer declarations and product-specific requirements rather than assuming that one compliance statement covers every regional obligation.

Engineering reference data for OPA137UA — comparison, design guidance, and compliance information.

Selection Guide

Choose the OPA137UA when the design needs a single-amplifier, 8-SOIC JFET input stage with very low bias current, a 1 MHz gain-bandwidth product, operation from a supply rated up to 36 V, and input common-mode range extending to the positive rail. It is particularly useful for electrochemical sensors, photodiodes, precision current measurement, and high-impedance instrumentation. OPA131UJ is the closest supported drop-in candidate when its manufacturer specifications satisfy the error budget and supply requirements. Before substituting it, compare bias current, offset, drift, noise, common-mode range, output swing, and capacitive-load stability. Neither the related dual OPA2137 nor quad OPA4137 devices are drop-in replacements for the single OPA137UA because their channel counts and internal pin assignments differ.

Comparison with Alternatives

Parameter This Product OPA131UJ
Brand Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC
Amplifier Type Single FET-input operational amplifier FET-input operational amplifier
Number of Channels 1 channel 1 channel
Gain-Bandwidth Product 1 MHz Approximately 1 MHz

Key Differentiators

  • High-voltage low-bias input stage (vs OPA131UJ)
  • Low-power precision operation (vs OPA131UJ)
  • Single-supply input headroom (vs OPA131UJ)

Design Notes

Place the supply bypass capacitor immediately next to pin 7, and connect pin 4 to the ground or negative-supply return with a short, low-impedance path. Keep pins 2 and 3 away from switching nodes, inductors, and high-current return paths. Because the OPA137UA is designed for very low bias current, remove flux residue and avoid exposed leakage paths around the input pins.

Protect the high-impedance input stage with guarding when humidity, contamination, or long PCB traces could create leakage paths. A guard surrounding the input can be driven by a low-impedance copy of the input potential, reducing leakage without loading the source. Keep guarding geometry well away from the sensitive input itself, and test the assembled board because connector and coating leakage can dominate the amplifier's input-current specification.

Do not assume that pin compatibility guarantees identical noise, drift, output drive, or stability. Before substituting OPA131UJ for OPA137UA, compare the full datasheets for common-mode range, output swing, gain-bandwidth behavior, capacitive-load limits, input bias current, offset voltage, and temperature drift. Recheck the feedback network and decoupling after any substitution, especially in high-gain or high-noise-gain circuits.

Compliance Information

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The JLCPCB product record identifies OPA137UA as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or automotive-qualification declaration is established here.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

opa137 datasheet OPA137UA datasheet pdf OPA137UA pinout OPA137UA specifications OPA137UA 36V 1MHz Texas Instruments OPA137UA OPA137UA equivalent OPA137UA replacement OPA137UA vs OPA131UJ OPA137UA application circuit OPA137UA price OPA137UA stock OPA137UA 8-SOIC footprint

Related Components & Terms

Texas Instruments OPA137UA OPA137 OPA131UJ OPA2137 OPA4137 FET-input operational amplifier JFET input stage operational amplifier analog amplifier semiconductor 8-SOIC SOIC package family surface-mount device rail-to-rail input input bias current gain-bandwidth product open-loop gain quiescent current input offset voltage slew rate signal conditioning electrochemical sensing photodiode interface RoHS
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details