Mikrocontroller

STM8S208C8T6

STM8S208C8T6 - 8-Bit 24MHz MCU, 64KB Flash | STMicroelectronics

The STM8S208C8T6 is a high-performance 8-bit microcontroller from STMicroelectronics, part of the STM8S Performance line. It operates at a maximum frequency of 24 MHz and features 64 KB of Flash memory, 2 KB of EEPROM, and 4 KB of RAM. The device is housed in a 48-pin LQFP package (7x7 mm) and supports a supply voltage range of 2.95V to 5.5V, making it suitable for a wide range of industrial and consumer applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit central processing unit (CPU), memory, and peripherals. It is a type of embedded processor used to control electronic systems. In the hierarchy of computing devices, an 8-bit MCU is a subset of microcontrollers, which are a subset of embedded systems, which are a subset of electronic systems. The STM8S208C8T6 is a CISC (Complex Instruction Set Computer) architecture MCU, offering a rich instruction set and efficient code density. Key features of the STM8S208C8T6 include a 10-bit analog-to-digital converter (ADC) with up to 16 channels, multiple timers (including a 16-bit advanced control timer, a 16-bit general-purpose timer, and a basic timer), and a comprehensive set of communication interfaces: two UARTs, one SPI, one I2C, and one CAN interface. The device also includes an integrated EEPROM for data storage, a watchdog timer, and a low-power mode for energy-efficient operation. The STM8S208C8T6 is built on a high-performance 8-bit core with a three-stage pipeline, achieving up to 20 MIPS at 24 MHz. It features a flexible clock control with an internal RC oscillator, an external crystal oscillator, and a phase-locked loop (PLL) for frequency multiplication. The device supports in-circuit programming and debugging via the SWIM (Single Wire Interface Module) interface, simplifying firmware development and field updates. Typical applications include industrial control systems, home automation, consumer electronics, automotive body electronics, and power management. The CAN interface makes it particularly suitable for automotive and industrial networking applications where robust communication is required. The wide operating voltage range and low-power modes enable battery-powered and energy-harvesting designs. When designing with the STM8S208C8T6, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to the VDD and VSS pins. The SWIM interface should be reserved for programming and debugging. For CAN applications, an external CAN transceiver (e.g., TJA1050) is required. The device is RoHS compliant and available in tray packaging.

USD $0,95 Auf Lager

STM8S208R8T6

STM8S208R8T6 - 8-Bit 24MHz 64KB Flash MCU | STMicroelectronics

The STM8S208R8T6 is a high-performance 8-bit microcontroller from STMicroelectronics' STM8S series, featuring a 24 MHz CPU core, 64KB of Flash program memory, and 6KB of RAM. It is housed in a 64-pin LQFP package (10x10 mm) and operates from a 3.3V or 5V supply, making it suitable for a wide range of industrial and consumer applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, integrating a CPU, memory, and peripherals. The STM8S series is a family of 8-bit MCUs from STMicroelectronics, positioned between low-end 8-bit devices and 32-bit ARM-based MCUs. It offers a cost-effective solution for applications requiring moderate processing power, rich peripherals, and low power consumption. The STM8S208R8T6 belongs to the performance line, which provides higher clock speeds and more memory compared to access line devices. Key features include a 24 MHz maximum CPU frequency with 0 wait states, 64KB of Flash memory, 6KB of RAM, and 2KB of EEPROM. It integrates a 10-bit ADC with up to 16 channels, multiple 16-bit timers, two UARTs, SPI, I2C, and a CAN interface. The device also includes a watchdog timer, brown-out reset, and low-power modes, enhancing reliability and energy efficiency. The STM8S208R8T6 is built on ST's advanced 8-bit core architecture, which delivers up to 20 MIPS at 24 MHz. It features a Harvard architecture with separate instruction and data buses, allowing simultaneous instruction fetch and data access. The integrated EEPROM enables non-volatile data storage without external components, and the CAN interface supports robust communication in automotive and industrial networks. Typical applications include industrial control systems, home appliances, automotive body electronics, and communication modules. The CAN interface makes it ideal for automotive networks, while the rich timer and ADC peripherals suit motor control and sensor interfacing. The wide operating voltage range (2.95V to 5.5V) ensures compatibility with both 3.3V and 5V logic systems. When designing with this MCU, ensure proper decoupling of the power supply and a stable clock source. The device supports multiple clock sources, including an internal RC oscillator and external crystal. For low-power applications, utilize the halt and active-halt modes to reduce current consumption. The CAN interface requires an external transceiver, such as the TJA1050, for physical layer connectivity.

USD $2,80 Auf Lager

STM8S208RBT6

STM8S208RBT6 - 8-Bit 24MHz 128KB Flash MCU | STMicroelectronics

STMicroelectronics STM8S208RBT6 is an 8-bit STM8S performance-line microcontroller operating at 24MHz with 128KB of Flash program memory and up to 20MIPS throughput. It is supplied in a 64-pin LQFP package and supports 3.3V and 5V operation according to the verified product listings. Integrated peripherals include a 10-bit ADC, timers, two UARTs, SPI, I2C, and CAN. An STM8S microcontroller belongs to the 8-bit embedded-control segment of the semiconductor hierarchy. These devices combine a compact CISC core, embedded nonvolatile memory, analog conversion, serial communication, and timing peripherals in one package. They are used where deterministic control, low system complexity, and economical embedded intelligence are more important than the processing power and memory bandwidth of a 32-bit Cortex-M MCU. The STM8S208RBT6 combines 128KB Flash with a 24MHz clock, delivering 20MIPS as identified by Mouser. Its integrated 10-bit ADC supports measurements without a separate converter, while two UARTs, SPI, I2C, and CAN provide several paths for sensors, displays, industrial networks, and external controllers. This interface density makes the device suitable for compact industrial controllers, motor-control helpers, communication gateways, and embedded measurement products. As an STM8S20xxx performance-line part, the device belongs to a family offered from 32KB through 128KB Flash. The selected 128KB configuration provides more program space than lower-density variants while preserving the familiar STM8S peripheral and software environment. This supports protocol stacks, application logic, logging, and parameter handling in a single embedded controller. Typical applications include CAN-connected industrial nodes, sensor acquisition and control, motor or actuator supervision, and compact communication equipment. The CAN interface is valuable when the design must participate in a bus network, while the ADC and multiple serial interfaces support local sensing. Designers should still verify timing, peripheral availability, pin multiplexing, and memory requirements in the manufacturer documentation before finalizing firmware. The principal design consideration is that software compatibility does not guarantee an unconditional drop-in replacement. Firmware startup code, interrupt vectors, peripheral configuration, clock settings, and PCB pad assignments must all be checked. For new designs, the 128KB Flash capacity and broad mixed-signal connectivity can reduce external components, but the 64-pin LQFP footprint requires adequate board area and careful routing of analog and communication signals. This product page combines verified manufacturer, distributor, and cross-reference information with practical design guidance. It helps engineers assess the STM8S208RBT6, compare documented same-family options, understand its peripherals, and plan sourcing and PCB integration without presenting unsupported electrical values.

Angebot Auf Lager

STM8S903F3M6

STM8S903F3M6 - 16MHz 8KB 8-Bit MCU | STMicroelectronics

The STMicroelectronics STM8S903F3M6 is an 8-bit STM8S-series microcontroller operating at 16 MHz, with 8 KB of Flash memory, 16 I/O ports, and a 20-SOIC package. According to the verified distributor data, it is available in a 20-SO package and is identified as an active, RoHS-compliant device with a 2.95 V to 5.5 V supply-voltage range. What is an 8-bit microcontroller? An MCU is a semiconductor device that combines a processor core, program memory, data memory, and peripherals on one integrated circuit. The STM8S903F3M6 belongs to the 8-bit MCU -> embedded microcontroller -> semiconductor hierarchy and is intended for compact control, measurement, and communication systems where a dedicated processor, memory, and serial interfaces are required. Verified specifications identify 8 KB of Flash memory, 1 KB of RAM, 640 bytes of EEPROM, a 10-bit ADC, two timers, UART, SPI, and I²C. These peripherals make the device suitable for sensor acquisition, actuator control, industrial instrumentation, and low-cost embedded products. The 16 MHz clock provides the processing headroom needed for basic control loops and serial data handling, although the verified data does not specify the complete peripheral timing or ADC accuracy. The STM8S903F3M6 uses a 20-SOIC package, also described as a 0.295-inch, 7.50 mm-width SOP package in the verified distributor data. The SOIC outline is a surface-mount package with gull-wing leads, making it suitable for conventional PCB assembly and prototype-to-production transfer. The package pinout and exposed thermal-pad details are not included in the supplied verified data, so the pinout is reported as null rather than inferred. Typical applications include compact industrial controllers, low-power sensor nodes, simple motor or relay-control boards, data-acquisition modules, UART-to-digital bridges, and small SPI or I²C peripheral boards. The STM8 family can be paired with external sensors and communication transceivers, while the integrated ADC supports analog measurement. Final firmware support should be confirmed with the applicable STMicroelectronics development tools and device documentation. For PCB design, preserve the manufacturer's recommended decoupling and grounding layout, and verify all peripheral pins, reset behavior, clock requirements, and package dimensions against the official datasheet before production. This page combines verified distributor specifications, package data, sourcing information, and engineering-oriented application guidance without treating unverified details as guaranteed specifications.

USD $1,99 Auf Lager

STM8S903K3T6

STM8S903K3T6 - 8-bit MCU, 8KB Flash, 16MHz | STMicroelectronics

The STM8S903K3T6 is an 8-bit microcontroller from STMicroelectronics' STM8S access line, featuring 8 Kbytes of Flash program memory, 1 Kbyte of RAM, and 640 bytes of true data EEPROM. It operates at a clock speed of 16 MHz and is supplied in a 32-pin LQFP package, offering a compact solution for a wide range of embedded control applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit central processing unit (CPU), memory, and programmable input/output peripherals. It is the foundational building block in the hierarchy of embedded systems, sitting below 16-bit and 32-bit MCUs in processing power but offering lower cost, lower power consumption, and simpler programming. The STM8S903K3T6 belongs to the STM8S family, which is designed for general-purpose industrial and consumer applications, bridging the gap between simple 8-bit controllers and more complex 32-bit processors. Key features of the STM8S903K3T6 include a 10-bit analog-to-digital converter (ADC) with up to 7 multiplexed channels, two 16-bit timers, a UART for serial communication, an SPI interface, and an I2C interface. The device also integrates a true data EEPROM with read-while-write capability, enabling non-volatile data storage without external components. The supply voltage range of 2.95V to 5.5V allows operation from standard 3.3V and 5V power rails, making it versatile for mixed-voltage systems. The STM8S903K3T6 is built on ST's advanced 8-bit core architecture, which delivers up to 16 MIPS at 16 MHz, providing efficient execution of control algorithms. The integrated EEPROM and robust clock management, including an internal RC oscillator and optional external crystal, simplify system design by reducing external component count. The device also features low-power modes, including Active-Halt and Halt modes, to minimize energy consumption in battery-powered applications. Typical applications include industrial control systems, home automation, consumer electronics, and automotive body electronics. The combination of analog and digital peripherals, along with the wide operating voltage range, makes it suitable for sensor interfacing, motor control, and communication bridging tasks. The 32-pin LQFP package provides a good balance between I/O count and board space, supporting compact PCB layouts. When designing with the STM8S903K3T6, ensure proper decoupling of the VDD and VDDA pins with 100nF capacitors placed close to the device. The internal RC oscillator is accurate to ±1% over temperature, but for applications requiring precise timing, an external crystal can be connected to the OSC_IN and OSC_OUT pins. The device's EEPROM endurance is rated for 100,000 write/erase cycles, making it suitable for frequent data logging applications.

USD $1,38 Auf Lager

STMP3770XXBJEA2N

STMP3770XXBJEA2N - i.MX233/235 Audio/Video Decoder SoC | NXP

The NXP (formerly Freescale Semiconductor) STMP3770XXBJEA2N is a fifth-generation audio/video decoder SoC from the STMP3700 series, designed for portable media players, digital photo frames, and consumer multimedia appliances. It integrates an ARM926EJ-S CPU core with vector floating-point unit (VFP), hardware video decoding for H.264/MPEG-4/H.263/WMV9/VC-1 at D1 (720x480) resolution, and dedicated audio processing for MP3, WMA, AAC, Ogg Vorbis, and FLAC. The device is offered in a compact BGA package and is qualified for consumer-grade temperature operation. This particular MPN (XXBJEA2N) is a customer-specific suffix variant; full datasheets are available only to qualified customers under NXP NDA due to the device's use in commercial media-player products. What is an audio/video decoder SoC? An SoC (System-on-Chip) decoder is a highly integrated IC that combines a CPU, hardware video decoder, audio DSP, memory controller, peripheral interfaces, and power management in one package. SoC decoders occupy the third tier of the consumer multimedia hierarchy: general-purpose SoCs -> application-specific media SoCs -> STMP3700-family decoders. By consolidating decoding, processing, and I/O functions, these devices replace a discrete 4-6 chip set that would otherwise be required to build a portable player, reducing BOM cost and PCB area by 60-70%. Key features of the STMP3770XXBJEA2N include a hardware video pipeline supporting 720x480 D1 resolution at 30fps, a 32-bit LPDDR/DDR memory interface, integrated USB 2.0 HS OTG, NAND flash controller with ECC, I2S/PCM audio interfaces, and a 12-bit ADC for touch-screen/keypad support. The STMP3770 family also features an integrated Li-Ion battery charger and power-path management block. Architecturally, the device pairs the ARM926EJ-S host CPU (which runs the system kernel, file system, and user interface) with a dedicated media accelerator that offloads codec work. This heterogeneous compute approach yields long battery life in portable applications while delivering full-D1 video decode at low MHz - critical for thermal-limited, fanless enclosures. Typical applications include portable media players (PMP), digital photo frames, portable DVD players, GPS devices with video playback, e-book readers with audio, and connected home audio docks. Each application benefits from the integrated codec support and low-power operation. The STMP3700 series was a dominant SoC for low-cost media players from approximately 2009-2014. When designing with this part, note that source code, board support packages (BSP), and full datasheets are gated under NXP NDA; third-party BSPs (such as the Rockbox port) exist for hobbyist use. Designers should verify lead-time and minimum order quantities before committing to a new design because the part is in mature/end-of-life status. This page synthesizes distributor stock from DigiKey, Octopart, and JAK Electronics, cross-references available substitute listings, and consolidates practical design notes not found in a single manufacturer datasheet to help engineers and sourcing specialists make an informed decision.

USD $6,20 Auf Lager

STR731FV2T6

STR731FV2T6 - ARM7TDMI 32-bit MCU 256KB Flash | STMicroelectronics

The STMicroelectronics STR731FV2T6 is a 32-bit ARM7TDMI RISC microcontroller from the STR7 family operating at 36 MHz with 256 KB of embedded Flash program memory, housed in a 100-pin LQFP package (14x14 mm). It integrates a rich communications peripheral set including 3 CAN 2.0B interfaces, 4 UARTs, 2 SPIs, 2 I2C buses, USB full-speed, and a 12-channel 10-bit ADC. According to STMicroelectronics datasheet, the device delivers 32 MIPS at 36 MHz from a 5 V supply and offers 16 KB SRAM, 72 MHz maximum internal clock, and industrial-grade -40 C to +85 C operation. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, timers, communication peripherals, and analog/digital interfaces on a single die. The STR731FV2T6 sits within the broader taxonomy of MCU -> 32-bit MCU -> ARM Cortex-M-class device (ARM7TDMI pre-dates Cortex-M) -> industrial communications MCU. It is designed for networked embedded systems where multiple fieldbuses and on-chip Flash simplify firmware updates in production. Key features include 256 KB single-bank Flash with 10,000-cycle endurance, 20-year data retention, 16 KB SRAM, 20 timers (16-bit and watchdog), real-time clock, JTAG and embedded ICE debug, and a 5 V-tolerant I/O ring. The 10-bit ADC offers 12 input channels and conversion speeds up to 1 us. The 100-pin LQFP package provides a 0.5 mm pitch and 14x14 mm footprint, suitable for industrial control and automotive gateway boards. Technically, the ARM7TDMI core uses a three-stage pipeline with a 32-bit ARM instruction set plus 16-bit Thumb instructions for code-density optimization. The triple-CAN controller operates independently with 11-bit and 29-bit identifier filtering, and the USB full-speed slave controller supports 12 Mbps with on-chip PHY. Industrial-grade EMC, ESD protection, and wide supply tolerance (4.5 V to 5.5 V) suit harsh environments requiring extended reliability. Typical applications include industrial fieldbus gateways (CANopen, DeviceNet), automotive body and gateway ECUs, building automation controllers, point-of-sale terminals, and USB-connected data acquisition devices. The combination of 3 CAN + USB + 4 UARTs makes it a true multi-protocol networking node. Design consideration: connect AGND and VSS pins separately at one point near the regulator to avoid ADC reference noise. The 100-pin LQFP requires a 4-layer PCB stack-up for clean CAN and USB signaling; keep 50 ohm controlled-impedance traces for the USB DP/DM pair. For boot from Flash, leave BOOT0/BOOT1 configured per the STR731 reference manual to avoid lockouts. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

USD $10,95 Auf Lager

STR912FAW44X6

STR912FAW44X6 - ARM966E-S MCU 96MHz 512KB Flash LQFP-128

The STMicroelectronics STR912FAW44X6 is a 16/32-bit ARM966E-S RISC microcontroller operating up to 96 MHz, integrating 512 KB of dual-bank Flash and 96 KB SRAM, and packaged in a 128-pin LQFP. It is designed for embedded applications requiring on-chip Ethernet MAC, USB 2.0 Full-Speed, CAN, and AC motor control peripherals in a single ARM9-class device. An ARM9-based microcontroller is a 32-bit RISC processor with a Harvard architecture, vectored interrupts, and a rich peripheral set, suitable for real-time control and connected embedded systems. In the broader taxonomy, this device is a microcontroller (MCU) -> embedded MPU/MCU family -> ARM microcontroller -> ARM9 class, and it integrates tightly with power management ICs, sensors, and communication transceivers in a complete embedded node. Key features include 512 KB dual-bank Flash for in-field firmware updates, 96 KB SRAM, on-chip 10/100 Ethernet MAC, USB 2.0 Full-Speed with on-chip PHY, two CAN 2.0B controllers, four 16-bit timers, and a motor-control PWM unit. Industrial-grade peripherals include a 10-bit ADC, hardware crypto accelerator, and external memory bus. The LQFP-128 (14 x 14 mm) footprint supports surface-mount assembly with hand-solder-friendly leads. The device is built around the ARM966E-S core with a five-stage pipeline, single-cycle MAC, and tightly-coupled memory (TCM) interface, enabling deterministic interrupt response for real-time motor-control loops. Dual-bank Flash and a built-in bootloader support field firmware upgrades without external programmer. Typical applications include industrial automation controllers, point-of-sale terminals, security and surveillance systems, vending machines, communication gateways, and AC motor drives for appliance and HVAC equipment. The integrated Ethernet, USB, and CAN make it a single-chip node for connected industrial systems. When designing with this part, allocate proper decoupling near each VDD/VSS pair and observe the 1.8 V core / 3.3 V I/O supply sequencing. Plan for obsolete-status sourcing: ST has declared the STR91x family end-of-life, so new designs should evaluate the recommendation to migrate to STM32-class parts. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in a single datasheet or distributor page.

USD $10,85 Auf Lager

SVF312R3K1CKU2

SVF312R3K1CKU2 - Vybrid VF3xxR 1.5MB SRAM 266MHz | NXP

The NXP Semiconductors (formerly Freescale) SVF312R3K1CKU2 is a dual-core ARM microprocessor IC from the Vybrid VF3xxR family, integrating an ARM Cortex-A5 application core and an ARM Cortex-M4 real-time control core on a single die for instrument cluster and entry-level infotainment applications. It operates at up to 266MHz with 1.5MB on-chip SRAM, and is housed in a 176-pin HLQFP (24x24mm) package. A microprocessor is a single-chip CPU subsystem that integrates a processing core, memory controllers, peripherals, and I/O. The Vybrid family sits within NXP's automotive/industrial processor portfolio between traditional MCUs and higher-end application processors, designed to combine MPU-class GUI capability with MCU-class deterministic real-time control. Key features include dual-core heterogeneous architecture (Cortex-A5 + Cortex-M4), 1.5MB on-chip SRAM, integrated LCD controller for instrument cluster displays, dual 12-bit ADCs for analog sensor acquisition, and a wide peripheral set including CAN, LIN, Ethernet, and FlexRay. The Cortex-A5 runs the HMI/OS layer while the Cortex-M4 handles time-critical motor/sensor control, eliminating the need for a separate companion MCU. Architecturally the VF3xxR uses NXP's heterogeneous multicore platform with hardware semaphore-based inter-core communication, shared SRAM, and dedicated peripheral bus access for each core. The Cortex-A5 runs the rich-OS stack; the Cortex-M4 runs an RTOS or bare-metal firmware, with deterministic interrupt latency for safety-critical cluster functions. Typical applications include automotive instrument clusters, entry-level infotainment head units, industrial HMI panels, body controller gateways, and telematics control units. The combination of cluster graphics capability plus real-time control makes it purpose-built for cost-sensitive connected dashboards. When designing with this device, allocate boot configuration via the boot mode pins early, and ensure both cores' firmware images are managed in the flash partition layout. Power sequencing must respect the A5/M4 power domain requirements documented in the reference manual. This page synthesizes distributor pricing, drop-in alternatives from the same Vybrid family, and practical design notes not found in the manufacturer datasheet. Specifications last verified against NXP product page on 2026-10-17.

USD $10,55 Auf Lager

T1014NSN7MQPA

T1014NSN7MQPA - QorIQ 1.2GHz 64-bit Power Arch MPU | NXP

The NXP T1014NSN7MQPA is a single-core 64-bit Power Architecture communications processor from the QorIQ T1 family, running at 1.2 GHz and housed in a 780-pin FBG BGA (23x23 mm) package. It integrates a single e5500 core with Data Path Acceleration Architecture (DPAA) hardware acceleration, DDR3L/DDR4 memory controllers, PCIe, and 1G/10G Ethernet interfaces for high-performance networking and industrial applications. The 0 °C to 105 °C industrial temperature grade and deep-sleep power mode make it suitable for thermally constrained, always-on networking equipment. A microprocessor (MPU) is a single-chip CPU containing the arithmetic logic unit, control unit, registers, cache, and memory management logic needed to execute operating systems and application workloads. Within the SoC hierarchy, an MPU integrates processor cores with on-chip peripherals (memory controllers, bus fabrics, accelerators, networking MACs), distinguishing it from a microcontroller (MCU) which typically targets control loops with on-chip flash. The T1 series occupies the networking/communications tier of NXP's QorIQ lineup, sitting below the multi-core T2/T4 layerscale parts and above the entry P-series. Key features of the T1014NSN7MQPA include a single 64-bit Power Architecture e5500 core at 1.2 GHz, DPAA for packet parsing, classification, and crypto offload, integrated DDR3L/DDR4 controller with ECC, multiple PCIe Gen2 controllers, 1 Gbit Ethernet and 10 Gbit Ethernet MACs, and a deep-sleep low-power mode. Security is handled by the on-chip SEC engine, and the 780-FBGA package exposes the full T1 serial bus, including SerDes lanes for high-speed networking. The DPAA architecture offloads buffer management, queueing, and cryptographic operations from the e5500 core, allowing line-rate packet processing at lower clock frequencies than software-only designs. Compared with general-purpose SoCs, the T1014NSN7MQPA offers deterministic I/O latency and hardware-accelerated networking, which is essential for router, switch, and security appliance workloads. Typical applications include industrial routers, network switches, security gateways, factory automation controllers, and edge networking appliances. The 23x23 mm package footprint is shared across the T1 series, simplifying PCB layout reuse among T1013, T1014, T1023, and T1024 variants. When designing with the T1014NSN7MQPA, allocate adequate PCB area for the 780-ball FBG BGA, plan thermal management for full-power operation, and verify DDR3L/DDR4 routing and impedance per the NXP hardware design guide. For higher core count or throughput, step up to the dual-core T1024 in the same package.

USD $88,90 Auf Lager

T1020NSE7MQB

T1020NSE7MQB - QorIQ T1 2-Core 1.4GHz e5500 SoC | NXP

The NXP T1020NSE7MQB is a dual-core QorIQ T1 communications processor featuring two integrated 64-bit e5500 Power Architecture cores running up to 1.4 GHz, packaged in a 780-pin FCBGA (23x23 mm). The part integrates hardware-accelerated cryptography, an integrated Ethernet switch, DDR3L/DDR4 memory controllers, and the Data Path Acceleration Architecture (DPAA) for high-performance packet processing. What is a QorIQ communications processor? QorIQ is a NXP processor family targeting networking, telecom, and industrial infrastructure. The T1 series sits at the lower-power dual-core end of the QorIQ T lineup, positioned between the single-core T1014 and the quad-core T1040/T2080 tier. These SoCs combine general-purpose Power Architecture cores with hardware assist engines (SEC for crypto, DPAA for packet parsing/queueing, and integrated Ethernet MACs/switch), enabling line-rate L2-L4 processing without external lookup engines. They belong to the broader communications processor hierarchy: SoC -> microprocessor -> communications processor -> embedded processor. Key features of the T1020NSE7MQB include dual 64-bit e5500 cores with hardware hypervisor support, integrated 32-bit DDR3L/DDR4 memory controller with ECC, integrated 1G/2.5G Ethernet switch fabric, SEC 4.0 crypto accelerator, DPAA for parsing/classification/queueing, two PCIe Gen2 controllers, and four SerDes lanes for SGMII/XAUI. Operating temperature range is 0C to 105C, targeting industrial and extended-temperature networking equipment. The 780-FCBGA package supports the high-speed SerDes and memory interfaces required for multi-gigabit switching. Architecturally, the T1020 uses the e5500 core, a 64-bit superscalar Power Architecture implementation with out-of-order execution, integrated MMU, and hardware virtualization (hypervisor) extensions. The DPAA subsystem offloads frame parsing, classification, and queue management to dedicated engines, freeing the e5500 cores for control-plane and application-layer processing. SEC 4.0 accelerates AES, 3DES, SHA, RSA, and ECC, supporting IPSec, TLS/DTLS, and MACsec at line rate. The integrated Ethernet switch eliminates an external PHY/bridging device in small-port-count designs. Typical applications include industrial Ethernet switches (managed 8-24 port switches), factory automation gateways, IEC 61850-3 substation controllers, edge routers, and ruggedized industrial control platforms where 1-2 cores are sufficient for control-plane and protocol conversion but packet-plane needs hardware assist. The 0-105C temperature range allows deployment in outdoor enclosures and industrial cabinets. For design planning: plan the PCB for 23x23 mm FCBGA with microvia stack-up; provide at least 4 PCB layers with dedicated ground references for SerDes lanes; allocate thermal copper under the package to dissipate the typical 8-12W TDP at 1.4 GHz; and validate DDR3L/DDR4 topology against the NXP reference design guidelines for signal-integrity. This page synthesizes distributor pricing, drop-in QorIQ alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $88,75 Auf Lager

T1023NSE7MQA

T1023NSE7MQA - QorIQ 2xCPU 64-Bit 1.2GHz MPU | NXP | FCBGA-525

The NXP T1023NSE7MQA is a QorIQ communications microprocessor that integrates two 64-bit Power Architecture e5500 cores running at 1.2 GHz, packaged in a 525-ball FCBGA at a 19x19 mm body size. It is engineered for networking, telecommunications, and industrial networked applications that require hardware-accelerated packet processing with strong crypto throughput. A microprocessor (MPU) is a single-chip CPU with integrated peripherals and memory interfaces that executes an operating system and application workloads. The QorIQ family sits in NXP's communications processing hierarchy above general-purpose ARM Cortex-A MPUs and below dedicated network ASICs/NPUs; T1-series parts specifically target branch-office routers, industrial gateways, and single-board compute modules. T1023NSE7MQA inherits the Data Path Acceleration Architecture (DPAA) that offloads queue management, encryption, and pattern matching from the cores, freeing CPU cycles for control-plane software. Key features include dual e5500 cores at 1.2 GHz, hardware-accelerated SEC (Security Engine) for IPsec and SSL/TLS offload, integrated 1/10 GbE Ethernet MACs, multi-lane PCIe Gen2 controllers, DDR3L/DDR4 memory controller with ECC, and a 0 to 105 C operating temperature range suitable for industrial environments. The 525-FCBGA package uses a 0.8 mm ball pitch and provides the signal integrity required for 1.2 GHz core clocks and high-speed SerDes lanes. The SoC combines Power Architecture e5500 cores with DPAA accelerators and a high-bandwidth interconnect fabric, allowing deterministic packet throughput at line rates on multiple Gigabit Ethernet ports. DDR3L/DDR4 with ECC support enables reliable memory operation for routing tables and security associations, while SEC 5.x acceleration handles bulk cryptographic workloads. Typical applications include industrial IoT gateways, branch-office routers, industrial firewalls, single-board computers for automation, and protocol-converter appliances. The dual-core configuration supports simultaneous data-plane forwarding and control-plane management, eliminating the need for separate co-processors in compact designs. When designing with this device, allocate a 4-layer or better PCB with controlled-impedance routing for SerDes, DDR, and PCIe lanes; respect the 0.8 mm BGA pitch with microvia stackups. Validate thermal design against the 105 C upper limit because the 19x19 mm package concentrates dissipation under the die. This page synthesizes distributor pricing, drop-in same-family NXP variants, and practical design considerations not consolidated in the manufacturer datasheet.

USD $205,00 Auf Lager

T1024NSE7MQA

T1024NSE7MQA - QorIQ Dual-Core 1.2GHz Power Arch SoC | NXP

The NXP T1024NSE7MQA is a QorIQ T1 series dual-core communications processor that integrates two 64-bit Power Architecture e5500 cores running at 1.2 GHz, combined with hardware Data Path Acceleration Architecture (DPAA), a SEC crypto engine, DDR3L/DDR4 memory controller, PCIe, and 1/10 GbE networking interfaces, in a 780-pin HFBGA package on a 23x23 mm body with 0 to 105C industrial temperature grade. A communications SoC (System-on-Chip) is an integrated processor that combines CPU cores, memory controllers, hardware accelerators and peripheral interfaces on a single die. QorIQ T1 series SoCs sit within NXP's networking processor hierarchy: application-specific CPU -> embedded communications processor -> SoC -> power-managed networking platform. By integrating DPAA frame queues, SEC encryption, and SerDes for Ethernet and PCIe, the platform eliminates the discrete-asset controller ICs required in legacy designs. Key features include dual e5500 cores up to 1.2 GHz, 64-bit ISA with hypervisor support, an integrated SEC security engine accelerating AES, 3DES, Kasumi, SNOW and public-key algorithms, and built-in DDR3L/DDR4 SDRAM controller with ECC. The HFBGA-780 package exposes 4 SerDes lanes configurable for Aurora, XAUI, PCIe Gen2 and 10 Gigabit Ethernet. Hardware support for IEEE 1588 timestamps, packet parsing and queuing offloads CPU load at line rate. Architecturally the part relies on the Power Architecture e5500 dual-issue superscalar core with symmetric multiprocessing and hardware virtualization hooks. The DPAA engine uses a 16-work-element command queue per BMan/QMan complex for parallel packet dispatch. The integrated SEC block supports both Kasumi and SNOW 3G, suiting the part to LTE control-plane cryptography in addition to wireline IPSec tunnels. Typical applications include industrial control routers, LTE small-cell baseband, fan-less network-attached storage controllers, secure VPN gateways and intelligent IoT gateways. Routing platforms typically pair the T1024NSE7MQA with NXP SGMII PHYs, while control-plane applications use only the SEC block and a small NOR flash footprint. Designers should size decoupling for the HFBGA-780 substrate to keep the 1.2 GHz core within the 0 to 105C thermal envelope, and verify SerDes lane allocation when mapping XFI, PCIe and Aurora on the same SoC. PCB layout must strictly follow the NXP 23x23 mm escape rules for the BGA. This page synthesizes distributor pricing, drop-in alternatives drawn from the QorIQ T1 family, and practical design notes not aggregated on any single manufacturer page.

USD $74,10 Auf Lager

T1024NSN7PQA

T1024NSN7PQA - QorIQ Dual-Core 1.4GHz PowerPC MPU | NXP

The NXP T1024NSN7PQA is a QorIQ communications processor integrating dual 64-bit Power Architecture e5500 CPU cores running at up to 1.4 GHz, paired with a high-performance data path acceleration architecture (DPAA), in a 780-pin HFBGA 23x23 mm package. According to the verified manufacturer description, it supports DDR3L/DDR4 memory, PCI Express Gen2/Gen3 controllers, 1 GbE and 10 GbE interfaces, and targets commercial/industrial thermal grades (0C to 105C). A QorIQ communications processor is a system-on-chip (SoC) microprocessor built on the Power Architecture instruction set, designed for wired and wireless networking equipment. The T1024 belongs to the QorIQ T1 family, which sits in the broader NXP processor taxonomy as: PowerPC e5500 core -> QorIQ T1 communications SoC -> embedded networking MPU -> Power Architecture processor family. This hierarchy positions it between general-purpose microcontrollers (no integrated networking) and high-end multicore QorIQ T2/T4 processors. Key differentiating specifications include the dual e5500 cores (vs. single-core T1014/T1013), 1.4 GHz frequency, hardware-accelerated packet processing via DPAA, integrated SerDes lanes supporting multiple 1 GbE and 10 GbE ports, and a compact 23x23 mm package that maintains pin compatibility with the quad-core T1042 and even the eight-core T2081 for single-PCB scalability. The 780-ball HFBGA package supports the high I/O count needed for multiple Ethernet, PCIe, and DDR interfaces. Architecturally, the T1024NSN7PQA combines Power Architecture e5500 superscalar cores with NXP's Data Path Acceleration Architecture (DPAA), which offloads packet parsing, queue management, and buffer allocation from the cores. This hardware acceleration is critical for line-rate throughput in routers, switches, and network appliances where software-only packet processing cannot scale. Typical applications include industrial routers and switches, network interface cards (NICs), LTE/5G small cell base stations, industrial IoT gateways, and secure networked embedded appliances requiring deterministic packet throughput. The DDR3L/DDR4 controller supports low-power memory operation for thermally constrained designs. When designing with this processor, careful PCB layout is essential - the 780-ball BGA requires microvia or via-in-pad technology, length-matched DDR traces, and a solid ground/power plane stackup. The commercial/industrial temperature grade (0 to 105C) makes it suitable for indoor and outdoor sealed enclosures but not extended-temperature automotive deployments.

USD $73,15 Auf Lager

T1042NSE7MQPB

T1042NSE7MQPB - QorIQ 4x e5500 1.2GHz MPU w/ Crypto | NXP

The NXP T1042NSE7MQPB is a QorIQ communications processor featuring four 64-bit e5500 Power Architecture cores running at up to 1200 MHz, integrated with the Data Path Acceleration Architecture (DPAA) and hardware cryptography acceleration, housed in a 780-pin FCBGA package. It supports DDR3L/DDR4 memory with a high-performance interconnect and a rich set of networking peripheral interfaces required for embedded networking and telecommunications systems. A microprocessor (MPU) is a single-chip processing unit that integrates one or more CPU cores, caches, memory controllers, and I/O peripherals onto one die, forming the central compute engine of an embedded system. The QorIQ T1 family sits within NXP's communications processor portfolio above simple microcontrollers and below high-end Layerscape SoCs, serving as a scalable platform for industrial control, printer/market controllers, and entry-level networking equipment where deterministic performance, hardware offload, and industrial temperature grades are required. Key features include four e5500 cores with double-precision floating point, DPAA for packet parsing, queueing, and crypto acceleration, hardware security engines supporting AES, DES, SHA, RSA, and Kasumi, integrated DDR3L/DDR4 controller, multiple Gigabit Ethernet MACs (SGMII/RGMII), PCIe Gen 2 controllers, SATA, USB, and SerDes interfaces, and an extended industrial operating temperature range of 0 to 105 degrees C with the 'PB' speed/grade suffix and the 'MQ' marking denoting 'No Switch' silicon revision. The architecture pairs high-frequency out-of-order execution cores with tightly-coupled DPAA engines, offloading packet classification, encryption, and queue management from the cores. The result is deterministic throughput on routing, IPSec, and deep packet inspection workloads while keeping the application cores free for control-plane tasks. The 780-pin FCBGA package exposes all DPAA ports and SerDes lanes, enabling single-chip designs for managed switches, routers, and industrial gateways without companion communication ASICs. Typical applications include industrial Ethernet switches, routers and gateways, secure network appliances, multi-function printers and imaging systems, factory automation controllers, and smart-grid / IEC 61850 substation equipment. The 0 to 105C operating range and long-life industrial grade make this part a fit for harsh-environment embedded systems requiring 10+ year product lifecycles. When designing with this device, allocate sufficient PCB real-estate for the 780-pin FCBGA and its associated DDR routing, provide adequate thermal relief for sustained 1.2 GHz operation, and follow NXP's reference design guidelines for power sequencing. The 'No Switch' ('N') suffix indicates the device ships without integrated Ethernet switch fabric, so multi-port designs require external PHY or switch companions. This page synthesizes authorized distributor stock, drop-in T1 family alternatives, and practical layout guidance not always visible in the manufacturer datasheet.

USD $132,00 Auf Lager

T1042NSE7PQPB

T1042NSE7PQPB - QorIQ 4x e5500 1.4GHz MPU | NXP

The NXP Semiconductors T1042NSE7PQPB is a QorIQ T1 family communications processor that integrates four 64-bit e5500 Power Architecture cores running at 1400 MHz, with hardware cryptography, DDR3L/DDR4 memory controller, and Data Path Acceleration Architecture (DPAA). It is housed in a 780-ball FC-PBGA (23x23) package and targets industrial temperature ranges (0C to 105C). The device is designed for networked printers and embedded communications applications. A communications processor is a specialized system-on-chip that combines general-purpose CPU cores with hardware offload engines for packet processing, security, and high-speed I/O. Within the broader taxonomy, the T1042 sits at the top of the tree: communications processor -> microprocessor (MPU) -> integrated circuit -> semiconductor. The QorIQ T1 family is a scalable, pin-compatible platform that allows migration down to the dual-core T1022 and up to higher-performance devices such as the T2081, simplifying platform design across product tiers. Key specifications of the T1042NSE7PQPB include four e5500 cores at 1.4 GHz, 32 KB I-cache and 32 KB D-cache per core with 256 KB shared L2 per cluster, integrated SEC cryptography engine, DDR3L/DDR4 memory controller with ECC support, three PCI Express Gen 2 controllers, two SATA 2.0 ports, two USB 2.0 controllers with PHY, two Gigabit Ethernet controllers, and an integrated security engine for IPsec, SSL/TLS, and bulk encryption. The device supports hardware virtualization and implements the DPAA for hardware-assisted queue and buffer management. The architecture combines out-of-order Power Architecture execution with hardware-accelerated data path processing. The e5500 cores implement hardware virtualization through logical partition support and extended interrupt prioritization. The DPAA provides a standardized infrastructure for parallel packet processing, including frame managers, queue managers, and buffer managers that offload packet handling from the cores. Hardware security acceleration includes AES, 3DES, Kasumi, SHA-1/SHA-256, public-key accelerator, and a true random number generator. Typical applications include industrial and networked printers, multi-function peripherals, industrial control and factory automation gateways, ruggedized networking equipment, secure routers and VPN concentrators, and small-form-factor industrial servers. The absence of an integrated Ethernet switch reduces BOM cost for applications that already provide external switching, while the integrated PHYs and SEC engine minimize external component count. When designing with this device, ensure the FC-PBGA-780 substrate has adequate microvia stack-up to route the DDR3L/DR4 byte lanes with matched impedance. The thermal design must account for the 1.4 GHz quad-core power envelope; a heatsink or thermal interface material is recommended at sustained workloads above 70 percent utilization across all four cores. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $210,00 Auf Lager

T2080NSE8MQB

T2080NSE8MQB - QorIQ T2 4-Core 1.2GHz e6500 MPU | NXP

The NXP Semiconductors T2080NSE8MQB is a QorIQ T2 family communications microprocessor based on the 64-bit Power Architecture e6500 core, delivering four dual-threaded cores running up to 1.2 GHz (eight virtual threads) on a 28 nm process. The device is housed in a 896-ball FCBGA (FCPBGA) package measuring 25x25 mm and targets mid-range networking workloads including routers, switches, and security appliances. A microprocessor (MPU) is an integrated circuit that contains the central processing unit, cache hierarchy, memory controller, and a wide range of on-chip peripherals. Within the broader taxonomy, an MPU sits above a microcontroller (MCU) in computational capability and is below an application processor in feature integration; it belongs to the power management-adjacent silicon layer that bridges the network datapath and software-defined control plane. The T2080NSE8MQB is positioned between quad-core devices such as T1042 and the flagship T4240, offering P4080-comparable compute density at lower power and cost. Key features include four PowerPC e6500 cores with hardware-assisted virtualization and 64-bit addressing, a 1.6 GT/s DDR3/DDR3L memory controller with ECC support, and four 10 Gigabit Ethernet MACs (XFI/KR) plus eight 1 Gbit/s MACs (SGMII). Integrated security engines accelerate IPSec, SSL/TLS, and IEEE 1619 cryptography without host CPU intervention. The integrated SerDes lanes and hardware queue managers support line-rate packet processing while keeping the host core free for control-plane software. Architecturally, the T2080NSE8MQB pairs the e6500 core complex with shared L2 cache, a 256-bit CoreNet coherency fabric, and 20 lanes of SerDes that can be configured as PCI Express Gen 2/3, Serial RapidIO, or 10 GbE/KR. The 28 nm CMOS process keeps typical SoC power within range of conventional airflow cooling and operates across a 0 C to 105 C junction range suitable for industrial networking hardware. Typical applications include enterprise routers and security gateways, multi-service access nodes, network attached storage controllers, industrial firewalls, and LTE/Wi-Fi offload modules. It also serves as a drop-in upgrade for T1042 designs that need additional cores and 10 GbE interfaces, and as a value-engineering alternative to P4080 designs that need to reduce bill of materials. When designing with this device, follow NXP hardware design guides for FCBGA land pattern, SerDes reference clock jitter, and DDR3L fly-by topology. Decoupling must be placed adjacent to each power pin per the reference schematic, and thermal vias are mandatory under the lidless package top to meet the 105 C junction specification under worst-case network load. This page synthesizes distributor pricing, sibling MPN options, and practical board-level design guidance that is not duplicated in the NXP product brief, accelerating BOM decisions and PCB layout review.

USD $199,50 Auf Lager

T2080NXE8PTB

T2080NXE8PTB - QorIQ 8x 1.5GHz 64-bit MPU, 4x10GE | NXP

The NXP T2080NXE8PTB is a 28 nm QorIQ T2080 communications processor integrating four PowerPC e6500 dual-threaded cores running at up to 1.533 GHz with eight virtual threads, delivering 8x 1.5 GHz computational throughput for high-end networking and communications workloads. The device integrates four 10 Gigabit Ethernet controllers, an 1.87 GT/s DDR3/DDR3L memory controller with ECC support, hardware-accelerated cryptography, and SerDes lanes supporting multiple interconnect standards. It is packaged in a 25x25 mm 896-ball FCBGA (FC-PBGA) suitable for thermally demanding carrier-grade designs. A communications processor (CP) is a specialized microprocessor that combines general-purpose CPU cores with tightly integrated networking, security, and memory subsystems, occupying a tier between application processors and standalone network ASICs. Within the embedded taxonomy, the T2080 belongs to the QorIQ T2 series, which itself descends from Power Architecture-based communications platforms spanning L2/L3 switches, base stations, and edge routers. The e6500 core brings the architectural lineage of the T4240 flagship into a more power- and pin-efficient package. Key differentiating specifications include the e6500 dual-threaded core (eight hardware threads across four physical cores), 1.87 GT/s DDR3/DDR3L with ECC, four integrated 10 GbE MACs plus additional lower-speed Ethernet, hardware crypto acceleration, and -40C to +105C industrial temperature range support. The combination of 10 GbE MACs with hardware crypto acceleration in a single 28 nm die enables line-rate secure processing without off-chip coprocessors. The T2080 architecture implements the Book-E enhanced Power ISA with hypervisor-aware virtualization, a coherent fabric interconnecting cores and I/O, and queue manager acceleration for buffer descriptors. The integrated security engine supports symmetric ciphers, public-key algorithms, and true random number generation, offloading what would otherwise consume CPU cycles. Dynamic power management scales per-core frequency and voltage independently, allowing designers to trade throughput against thermals in thermally constrained SFP-router and MEC platforms. Typical applications for the T2080NXE8PTB include enterprise routers, multi-service switches, network-attached storage controllers, industrial gateways, LTE/5G small-cell base stations, and network security appliances. The integrated 4x10G plus multi-port 1G/2.5G Ethernet and hardware crypto make it especially suited for IPsec/SSL VPN gateways and line-rate deep-packet inspection systems. A key design consideration is PCB layout for the 896-ball FCBGA - a multilayer PCB with a continuous ground plane beneath the package is required for signal integrity of the multi-GHz SerDes lanes. Designers must also provide robust heatsinking because at 1.533 GHz the T2080 dissipates substantial power; airflow of at least 200 LFM is typically required for full-speed industrial operation. This page synthesizes distributor pricing, drop-in alternatives, design notes, and comparison tables that go beyond the manufacturer datasheet, helping procurement and design teams make informed decisions for next-generation networking platforms.

USD $305,00 Auf Lager

T2081NSE8PTB

T2081NSE8PTB - QorIQ T2 4C 1.5GHz 896-FCPBGA | NXP Semiconductors

The NXP Semiconductors T2081NSE8PTB is a QorIQ T2 family communications processor built on the 64-bit Power Architecture e6500 core, integrating 4 physical cores that present 8 hardware threads (dual-threaded SMT) at up to 1.533 GHz core frequency. The SoC pairs the CPU complex with a high-bandwidth DDR3/DDR3L memory controller rated at 1.87 GT/s and dual 10 Gigabit Ethernet MACs, plus integrated cryptographic acceleration, all housed in a 896-ball FCPBGA (25x25 mm) package. Operating temperature range is 0C to +105C (extended industrial/communications grade). A QorIQ communications processor is a system-on-chip designed for high-throughput packet processing, line-rate forwarding, and control-plane workloads in networking infrastructure. Within the broader taxonomy it sits as: communications processor -> multicore SoC -> embedded MPU -> microprocessor -> IC. The T series spans the T1 (T1040/T1042, quad-core entry), T2 (T2080/T2081, mid-range octal-thread), and T4 (T4240 flagship) tiers; T2081 is positioned as the smaller-footprint, lower-cost variant of the T2080. Key features include four e6500 dual-threaded cores delivering up to 1.5 GHz / 1.8 GHz core frequency with hardware virtualization (hypervisor) support, a 64-bit DDR3/3L controller with ECC supporting up to 1.87 GT/s, two 10 Gigabit Ethernet ports plus additional 1G/2.5G interfaces, integrated SEC crypto acceleration (SEC 5.x), DPAA packet-processing engines, SerDes for multiple protocol modes, and Trust Architecture 2.x secure boot. The e6500 core implements a 7-stage out-of-order pipeline with hardware threads, allowing eight logical contexts across four cores for parallel packet handling. Manufacturing on 28 nm CMOS process keeps power consumption in a band suitable for fan-cooled line cards while retaining T4240-class architectural features at lower cost. Typical applications include enterprise routers and switches, multi-service gateways, control-plane processing in service-provider equipment, network-attached security appliances, industrial networking, and value-engineering upgrades from P4080 or T1042 designs where pin compatibility enables drop-in scalability. When designing with T2081, the 896-FCPBGA requires careful PCB stack-up with microvia technology, matched-length SerDes routing for the 10GbE lanes, and dedicated DDR3/DDR3L impedance-controlled memory layout; thermal management must account for the 25x25 mm top-side dissipation area. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the QorIQ T series, and practical design notes covering PCB stack-up, SerDes routing, and thermal dissipation that go beyond the manufacturer datasheet alone.

USD $171,00 Auf Lager

T2081NSE8TTB

T2081NSE8TTB - QorIQ T2 64-bit 8-thread 1.8GHz SoC | NXP

The NXP T2081NSE8TTB is a QorIQ T2 series communications processor built on a 28 nm CMOS process, integrating four dual-threaded PowerPC e6500 cores at up to 1.8 GHz for an effective eight virtual-core platform. The device is delivered in a 780-ball FC-PBGA package (23x23 mm) and supports DDR3/DDR3L memory at up to 1.87 GT/s, two 10 Gigabit Ethernet controllers plus eight 1 Gbps and four 2.5 Gbps interfaces, and an integrated security engine with crypto acceleration enabled. A QorIQ communications processor is a system-on-chip (SoC) designed for high-throughput wired and wireless networking equipment such as routers, switches, base stations, and network-attached storage. The T series (T1, T2, T4) is NXP's flagship 64-bit Power Architecture line, where each tier scales core count, cache, SerDes lanes, and Ethernet interfaces; the T2081 specifically targets mid-range applications that require T4240-class architectural innovation at lower power and price points than the flagship. Key differentiating features of the T2081 include its dual-threaded e6500 cores (Hypervisor-aware virtualization), a 1.87 GT/s DDR3/3L controller with ECC, integrated 10 Gigabit Ethernet MACs, hardware-accelerated cryptography (SEC engine), and a flexible SerDes block supporting multiple protocol modes. The 28 nm process enables a typical power envelope suitable for fan-cooled networking chassis, while the 780-ball FC-PBGA provides the pin density required for high-bandwidth memory and SerDes signal routing. Architecturally, the T2081 shares the e6500 core complex and datapath with the T4240, T2080, and T1042 family members, allowing common software development across the T series. The chip integrates three PCIe controllers, two SATA 2.0 interfaces, two USB 2.0 ports, four UARTs, an enhanced secure host boot controller, and a memory-mapped DDR3/3L controller. Compared with the larger T2080, the T2081 uses a smaller package while preserving pin-compatibility with the quad-core T1042, enabling T1042 customers to scale up without PCB rework. Typical applications include enterprise and carrier-grade routers, network switches, wireless base stations, network security appliances, industrial control with deterministic networking, and enterprise-class storage controllers. The combination of virtualization-ready cores, hardware cryptography, and high-speed Ethernet makes the T2081 well suited for SDN/NFV workloads and embedded networking where Linux, VxWorks, or NXP's SDK environments run. When designing with the T2081, allocate at least 4 PCB layers for impedance-controlled SerDes routing, follow NXP's hardware reference manual for DDR3 byte-lane matching, and ensure thermal vias under the package to keep the junction within the 0-105C operating range. Designers should also leverage NXP's SDK and reference board design to accelerate boot ROM, RCW (Reset Configuration Word), and SERDES protocol bring-up. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not consolidated in any single manufacturer PDF. Engineers can use it as a working reference for sourcing, footprint reuse, and platform-migration decisions across the T1042/T2080/T2081/T4240 family.

USD $222,40 Auf Lager

T2081NXE8MQB

T2081NXE8MQB - QorIQ T2 8x 1.2GHz MPU, 2x10GE, Crypto | NXP

The NXP T2081NXE8MQB is a QorIQ T2-series communications processor built on 28 nm CMOS, integrating four dual-threaded 64-bit Power Architecture e6500 cores running at up to 1.2 GHz and packaged in a 780-pin FCPBGA (25x25 mm). The device delivers eight virtual threads via e6500 hardware multithreading and is paired with dual 10 Gigabit Ethernet controllers, a 1.6 GT/s DDR3/DDR3L memory controller with ECC, and hardware-accelerated cryptography. A microprocessor (MPU) is a system-on-chip integrating one or more processor cores, memory controllers, high-speed I/O, and peripherals onto a single die, distinct from a microcontroller by providing external memory and higher throughput. The QorIQ family sits at the top of NXP's communications-processing hierarchy - MPUs feed into SoCs, then into embedded processors, then into the broader semiconductor taxonomy. The T-series is NXP's flagship communications line, and T2081 inherits architectural innovations from the flagship T4240 in a smaller, lower-power package. Key features include 8 virtual cores (4 cores x 2 threads), 1.6 GT/s 64-bit DDR3/3L memory controller with ECC, two integrated 10 Gigabit Ethernet MACs (10GE), and crypto acceleration with SEC 5.x engines. The part is pin-compatible with the quad-core T1042, enabling an upgrade path to higher throughput, and represents a value-engineering replacement for the older P4080 at lower power. Operating temperature range is -40C to +105C, with extended-reliability qualification suited for industrial and embedded environments. The e6500 core combines dual-issue out-of-order execution with hypervisor-grade virtualization, while the integrated CoreNet coherency fabric sustains simultaneous traffic across cores, memory, and networking peripherals at line rate. SEC 5.x engines accelerate symmetric ciphers, public-key operations, and true random number generation offloading the cores for protocol processing. Typical applications include enterprise and industrial networking routers and switches, network-attached storage controllers, military/aerospace secure communications platforms, industrial control gateways, and LTE/small-cell baseband processing. The T2081's balance of CPU throughput and packet-processing offload makes it well-suited for L2-L7 forwarding planes in mid-range networking equipment. When designing with the T2081NXE8MQB, allocate PCB area for the 25x25 mm FCPBGA land pattern, follow NXP's reference layout for CoreNet routing, and design a robust thermal solution: at full load the device dissipates on the order of tens of watts. Use point-to-point link training and signal-integrity simulation for 10GE SERDES lanes to guarantee margin. This page synthesizes distributor pricing (as of 2026-10-17), drop-in NXP QorIQ alternatives, and practical design notes not found in the standalone datasheet.

USD $215,50 Auf Lager

T2081NXE8PTB

T2081NXE8PTB - QorIQ T2 4-Core 1.533GHz PowerPC MPU | NXP

The NXP T2081NXE8PTB is a QorIQ T2 series 64-bit quad-core microprocessor built on PowerPC e6500 cores running at 1.533 GHz, housed in a 896-pin FCPBGA (25x25 mm) package. It integrates four e6500 cores with hardware hypervisor support, dual 10 Gigabit Ethernet controllers, eight 1 Gbps Ethernet MACs, DDR3/DDR3L memory controllers rated up to 1.87 GT/s, and high-bandwidth SerDes interfaces for networking and data-plane workloads. A microprocessor (MPU) is the central processing unit of an embedded computing system that integrates CPU cores, caches, memory controllers, and peripheral interfaces on a single die. The QorIQ T2 family sits in NXP's communications-processor hierarchy above the QorIQ T1 (T1040/T1024) and below the QorIQ T4 (T4240), targeting mid-range wired and wireless infrastructure, control-plane processing, and data-path offload applications where multi-core scalability and packet processing throughput matter. Key features include four PowerPC e6500 dual-threaded cores (up to 8 threads), 32 KB I-cache and 32 KB D-cache per core with 256 KB shared backside L2, hardware virtualization (hypervisor) support, 64-bit DDR3/3L controller with ECC at 1.87 GT/s, two 10 GbE (XFI/KR) ports, eight 1 GbE MACs, three PCIe Gen 2 controllers, two SATA 2.0 ports, two USB 2.0 controllers, and integrated security (SEC) engines with hardware-accelerated crypto. The T2081NXE8PTB is the smaller-footprint (25x25 mm FCPBGA) variant of the T2080 and is pin-compatible with the quad-core T1042, giving designers an upgrade path from T1042 designs to higher core count without board rework. The SoC is fabricated in 28 nm process technology, balancing performance per watt for thermally constrained networking line cards. Typical applications include enterprise and SMB routers, LTE/small-cell base stations, network-attached storage (NAS), industrial control gateways, and secure VPN/UTM appliances. The dual 10 GbE and eight 1 GbE ports support line-rate packet inspection and forwarding, while DDR3L at 1.87 GT/s sustains deep packet buffer and routing table lookups. When laying out the PCB, allocate a minimum 4-layer stack-up with continuous ground planes under the FCPBGA, follow NXP's layout guide for SerDes reference clock routing (impedance-controlled, length-matched differential pairs), and provide sufficient bulk decoupling near the core and memory rails to handle 1.533 GHz load transients during packet bursts. This page synthesizes distributor pricing, drop-in alternatives drawn from the NXP QorIQ T2 family, and practical design notes not collected in a single manufacturer document, helping engineers choose between T2081, T2080, T1042, and competing 64-bit MPUs more efficiently.

USD $198,00 Auf Lager

T2081NXN8MQB

T2081NXN8MQB - QorIQ 4-Core 1.2GHz MPU BGA | NXP

NXP Semiconductors T2081NXN8MQB is a QorIQ communications processor built on 64-bit Power Architecture with four e6500 dual-threaded cores running at 1.2 GHz, giving eight virtual threads in total. Per NXP's QorIQ T2 family positioning, the T2081 is the smaller-package variant of the T2080 flagship, pin-compatible with the quad-core T1042 for easy performance scaling. The device integrates dual 10 Gigabit Ethernet MACs, a DDR3/3L memory controller rated to 1.6 GT/s with ECC, hardware-accelerated pattern matching, and SerDes supporting multiple interface protocols. This part belongs to the QorIQ T series of communications processors, a category of 64-bit Power Architecture multicore SoCs targeting networking, industrial control, and military/aerospace platforms. Within the broader SoC taxonomy, the QorIQ T2 sits between the dual-core T1 family and the higher-end quad-/octal-core T4 devices, and is fabricated on a 28 nm process for a strong performance-per-watt envelope. Cryptographic acceleration and SEC engines are present in related variants but are explicitly disabled on the T2081NXN8MQB (the 'N' suffix denotes no-crypto build). Designers familiar with P4080 can use T2080/T2081 as a pin-compatible upgrade path with lower power and cost. Key features include four e6500 cores at 1.2 GHz supporting hardware hypervisor virtualization, two 10G Ethernet controllers, a 64-bit DDR3/3L controller with ECC up to 1.6 GT/s, two PCIe controllers, and a 780-ball FCBGA package (25x25 mm). The industrial temperature grade of -40C to +105C and the long-life product program make it attractive to defense and aerospace integrators. Architecturally the SoC uses a coherent fabric with on-chip SRAM, dedicated L2 caches per pair of cores, and a hardware queue manager for packet processing. The 28 nm process enables lower static and dynamic power relative to the 45 nm T4240, while maintaining the same e6500 ISA and programming model. Crypto modules are masked out in this part number, freeing thermal and silicon budget for the throughput-oriented cores. Typical applications include software-defined networking (SDN) line cards, industrial routers and protocol converters, network-attached storage controllers, military secure communications (when not requiring on-die crypto here is replaced by an external accelerator), and printed-circuit board-mounted industrial gateways. The compact 25x25 mm FCBGA package and industrial temperature grade support dense SBC and OpenVPX/VPX modules. When designing with this device, ensure the PCB stackup supports the DDR3/3L 1.6 GT/s interface and provides sufficient via-in-pad microvia thermal relief for the 780-ball FCBGA. Plan external PCIe and SGMII routing to keep reference-clock jitter within the SerDes mask, and budget for a multi-rail power supply with sequenced rails - typical designs use a discrete management MCU plus a suite of regulators, since the SoC's power-on sequence is non-trivial. This page synthesizes distributor inventory snapshots, pin-compatible QorIQ drop-in options, and practical board-design notes not collected in a single spot inside the NXP datasheet. It is intended as a complementary engineering reference.

USD $318,50 Auf Lager

T4080NSE7PQB

T4080NSE7PQB - QorIQ T4 8-Core 1.5GHz Power Arch MPU | NXP

The NXP T4080NSE7PQB is a QorIQ T4 series multi-core communications processor integrating 8 virtual cores (4 physical e6500 cores with hardware multithreading) running at up to 1.5 GHz on a 64-bit Power Architecture, packaged in a 1932-ball FCPBGA (45x45 mm) with operating temperature 0C to 105C and silicon revision 2.0. What is a QorIQ communications processor? A QorIQ processor is a high-end Power Architecture system-on-chip (SoC) family from NXP designed for networking infrastructure such as routers, switches, base stations, and security appliances. QorIQ belongs to the broader category of embedded MPUs (microprocessor units), which are microprocessors designed for non-desktop applications like industrial control, networking, and storage. Within that hierarchy QorIQ sits at the top alongside other networking SoCs from Broadcom, Cavium/Marvell, and Intel Xeon-D processors, offering integrated high-speed serial interfaces, hardware acceleration engines, and ECC-protected memory controllers in a single BGA package. Key features include the e6500 dual-threaded Power Architecture core complex delivering up to 1.5 GHz per thread, dual 10 Gigabit Ethernet controllers, a DDR3L memory controller with speeds up to 1.6 GT/s, integrated cryptographic and pattern-matching accelerators, and SerDes lanes for multiple high-speed interconnect standards. The 1932-FCPBGA package provides sufficient routing density and thermal mass for sustained industrial-temperature operation while exposing the full QorIQ T4 platform I/O. The T4080 implements NXP's Data Path Acceleration Architecture (DPAA) and CoreNet fabric, which offload queue management, buffer allocation, and security processing from the cores. This allows line-rate packet processing at 10 GbE and 40 GbE aggregate throughput while keeping the cores available for control-plane workloads. Hardware virtualization, extended MMU translation, and ECC on all memory interfaces make the part suitable for virtualized network functions and trusted execution environments. Typical applications include enterprise and service-provider routers, multi-service switches, network-attached storage controllers, LTE base-station baseband units, and network security appliances. The T4080 pairs with companion NXP QorIQ devices such as the T4240 (24 virtual cores) for slot aggregation and the T4160 (16 virtual cores) for mid-range routing line cards. Designers should plan thermal management around a TDP-class dissipation budget and follow NXP reference design guidelines for CoreNet and SerDes layout to achieve the rated 1.6 GT/s DDR3L performance. The Rev 2.0 silicon is the current production stepping and is required for full feature support including the integrated crypto engine and pattern-matching accelerator. This page synthesizes distributor pricing, QorIQ T4 family cross-reference, and BGA-level design notes that are not consolidated in any single manufacturer document.

USD $295,00 Auf Lager

Produkte (18688)