AD600AQ - Dual 35MHz Low-Noise VGA | Analog Devices
Teilenummer: AD600AQ ✓ AktivAD600AQ Übersicht
A variable gain amplifier, or VGA, is an analog signal-conditioning amplifier whose gain is adjusted by an external control voltage. Its position in the signal chain is between a low-level source and a downstream measurement, imaging, or conversion stage. The AD600 belongs to the broader hierarchy of voltage-controlled amplifiers, instrumentation amplifiers, analog amplifiers, and integrated analog circuits. Independent channel control allows two signal paths to be adjusted separately, which is valuable when two ultrasound echo channels require different gains or calibrated attenuation.
The AD600AQ combines a 1.4 nV/√Hz input-noise density with a 35 MHz -3 dB bandwidth and gain accuracy of 0.3 dB. Its linear-in-decibel control characteristic helps maintain consistent amplitude behavior across a broad gain range. The amplifier also supports low-distortion operation, with the manufacturer data listing -60 dBc third-harmonic distortion for a 1 V output. These characteristics make it suitable for systems that require both signal-to-noise performance and predictable gain calibration.
The dual-channel architecture provides separate high-impedance inputs and gain-control paths for each amplifier section. The 275 V/µs slew rate supports rapid amplitude transitions, while the wide bandwidth allows the device to process signals extending into the ultrasonic imaging range. Because the gain is voltage controlled, an external control voltage can support automatic gain control, attenuation, calibration, or signal-level normalization without mechanical adjustments.
Typical uses include ultrasound imaging receivers, medical ultrasound diagnostic equipment, dual-channel instrumentation, broadband signal analyzers, communication receivers, and precision test systems. In an ultrasound receiver, the AD600AQ can amplify weak echo signals while independent gain control supports channel-specific calibration and time-gain compensation. Its low noise is valuable when the gain must be increased enough to reveal signals close to the input noise floor.
Designers should use the manufacturer pin-description table to assign all 16 CERDIP connections and preserve the recommended dual-supply decoupling. Stable operation requires adequate bypass capacitance at the supply pins and careful grounding because high-speed signals can couple between the two channels. Gain-control voltage range, input impedance, output swing, and recommended source and load impedances should be taken directly from the manufacturer datasheet for the target board revision.
This page organizes the AD600AQ specifications, verified sourcing references, package information, a qualified AD602AQ comparison, and practical design guidance. The comparison is specifically limited to the same 16-lead CERDIP footprint, and any replacement should be checked against gain range, control-voltage behavior, bandwidth, supply voltage, pin assignments, temperature rating, and signal-integrity requirements before production use.
Drop-in-Alternativen für AD600AQ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
AD602AQ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD600AQ Grenzwerte & elektrische Eigenschaften
| Number of Channels | 2 channels |
| Amplifier Type | Dual, low-noise, wideband variable gain amplifier |
| Gain Control | Independent voltage control per channel |
| Gain Response | Linear in dB |
| Gain Range | Up to +30 dB |
| Absolute Gain Accuracy | 0.3 dB |
| Input Noise Density | 1.4 nV/√Hz |
| Third-Harmonic Distortion | -60 dBc at 1 V output |
| Signal Bandwidth | 35 MHz at -3 dB |
| Slew Rate | 275 V/µs |
| Supply Voltage Range | ±4.75 V to ±5.25 V |
| Betriebstemperaturbereich | -40°C to +85°C |
| Gehäuse | 16-lead CERDIP (Q), 7.62 mm |
| Montageart | Through-hole |
| Technology | CMOS |
AD600AQ 16-lead cerdip (q), 7.62 mm Pinbelegungsleitfaden
Pinbelegung für AD600AQ (16-lead cerdip (q), 7.62 mm-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für AD600AQ.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
AD600AQ ist geeignet für 6 Anwendungs: Medical Ultrasound Echo Amplification, Industrial Ultrasound Inspection, Wideband Automatic Gain Control, Instrumentation Signal Conditioning, Communications Receiver Front End, Precision Test and Measurement.
Medical Ultrasound Echo Amplification
The AD600AQ fits medical ultrasound echo receivers because each of its two channels provides independent voltage-controlled gain, a 1.4 nV/√Hz input-noise density, and a 35 MHz -3 dB bandwidth. The amplifier can sit between the transducer receiver circuitry and later processing stages, raising weak echo voltages while preserving the wideband information needed for time-of-flight measurement. Its +30 dB gain range and 0.3 dB absolute gain accuracy support controlled channel calibration. The main design consideration is that the two channels operate from separate ±4.75 V to ±5.25 V rails, requiring close supply bypassing and careful grounding.
Empfohlen
Industrial Ultrasound Inspection
The AD600AQ is suitable for industrial ultrasonic inspection equipment that must recover small reflected signals across a wide frequency range. Its 35 MHz -3 dB bandwidth accommodates high-frequency echo content, while the 1.4 nV/√Hz input-noise density limits the input-referred noise that becomes dominant as gain increases. Independent gain control allows separate receive channels to be balanced for different probe paths or inspection sequences. The 275 V/µs slew rate supports rapid signal transitions, but the layout should keep gain-control routing away from sensitive inputs and use stable, low-impedance references for calibration.
Empfohlen
Wideband Automatic Gain Control
The AD600AQ can implement a dual-channel automatic gain-control stage when both signal amplitude and control voltage are available to a feedback loop. Its linear-in-decibel response is useful because gain changes remain approximately proportional across a 30 dB operating interval, and the 0.3 dB absolute gain accuracy provides a defined calibration target. The 35 MHz bandwidth permits the loop to operate on high-frequency waveforms rather than only low-frequency envelopes. Designers should keep loop compensation separate from the analog input path and account for the amplifier's 275 V/µs slew rate when choosing detector and compensation components.
Empfohlen
Instrumentation Signal Conditioning
The AD600AQ is appropriate for precision instrumentation that must condition two analog channels over a broad frequency range. Its low 1.4 nV/√Hz input-noise density, 0.3 dB gain accuracy, and -60 dBc third-harmonic distortion at a 1 V output are useful for sensors and receivers where amplitude integrity matters. Independent voltage control can support range switching, attenuation calibration, or normalization before digitization. The wide bandwidth must be matched by controlled board impedance and short return paths, while the dual-supply architecture should be decoupled at the device to limit noise on the rails.
Empfohlen
Communications Receiver Front End
The AD600AQ can serve as a wideband receive-stage gain control element when two related channels require independent attenuation. The 35 MHz bandwidth is appropriate for broadband communication and test signals, while voltage-controlled gain simplifies automatic adjustment of signal levels. Low input noise supports operation near the receiver sensitivity limit, and the 0.3 dB absolute gain accuracy supports repeatable level adjustment. Because wideband gain stages can amplify interference as well as wanted signals, use a controlled ground reference, place bypass capacitors at the supply pins, and keep the gain-control traces away from high-impedance input nodes.
Empfohlen
Precision Test and Measurement
The AD600AQ is useful in test systems requiring programmable attenuation or gain across two measurement channels. Its gain is controlled by voltage and has a linear-in-decibel response, simplifying many calibration tables, while the 1.4 nV/√Hz input-noise density supports low-level measurements. The 35 MHz bandwidth accommodates pulse and wideband test signals, and the 275 V/µs slew rate helps preserve amplitude during rapid transitions. For metrology-grade results, evaluate channel-to-channel gain matching against the 0.3 dB absolute accuracy figure, isolate the gain-control source, and calibrate the complete installed circuit rather than relying only on component-level values.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für AD600AQ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | AD602AQ |
|---|---|---|
| Package | 16-lead CERDIP (Q), 7.62 mm | 16-lead CERDIP (Q), 7.62 mm |
| Brand | Analog Devices | Analog Devices |
| Number of Channels | 2 channels | 2 channels |
| Gain Control | Independent voltage control | Independent voltage control |
Wichtigste Unterscheidungsmerkmale
- Independent dual-channel gain adjustment (vs. AD602AQ)
- 35 MHz signal bandwidth (vs. AD602AQ)
- Low-noise dual-channel amplification (vs. AD602AQ)
- Defined gain accuracy and range (vs. AD602AQ)
Designhinweise
Place the positive and negative supply bypass capacitors immediately beside their corresponding AD600AQ pins. Keep the high-frequency return current within the smallest possible loop area and use a continuous ground reference beneath the signal path. The two amplifier channels are wideband and low-noise devices, so long supply traces and shared return paths can degrade channel isolation, output noise, and distortion even when the schematic is electrically correct.
Route the two high-impedance inputs as short and symmetrically terminated traces, and keep the independently controlled gain-input traces physically separated from the signal inputs. Reference the gain-control source to the same low-impedance ground used by the supply bypass network. Poor isolation between control and signal routes can couple modulation or switching artifacts into the amplified output even when the 1.4 nV/√Hz input-noise specification is met in the laboratory.
Do not treat the 16-lead CERDIP footprint as proof of electrical interchangeability. Before replacing the AD600AQ with the AD602AQ, compare gain range, gain-control voltage, supply requirements, bandwidth, noise, distortion, and every pin function against the manufacturer data for both devices. Also confirm that the ceramic package is suitable for the board's mechanical and soldering process; a package-compatible substitute can still fail if its electrical interface differs.
Compliance-Informationen
The manufacturer product page and AD600AQ technical information do not state the requested environmental-compliance statuses. The industrial-temperature AD600A grade is not, by itself, an AEC-Q100 automotive qualification.