AD600AQ - Dual 35MHz Low-Noise VGA | Analog Devices
料号: AD600AQ ✓ 量产中AD600AQ 概述
A variable gain amplifier, or VGA, is an analog signal-conditioning amplifier whose gain is adjusted by an external control voltage. Its position in the signal chain is between a low-level source and a downstream measurement, imaging, or conversion stage. The AD600 belongs to the broader hierarchy of voltage-controlled amplifiers, instrumentation amplifiers, analog amplifiers, and integrated analog circuits. Independent channel control allows two signal paths to be adjusted separately, which is valuable when two ultrasound echo channels require different gains or calibrated attenuation.
The AD600AQ combines a 1.4 nV/√Hz input-noise density with a 35 MHz -3 dB bandwidth and gain accuracy of 0.3 dB. Its linear-in-decibel control characteristic helps maintain consistent amplitude behavior across a broad gain range. The amplifier also supports low-distortion operation, with the manufacturer data listing -60 dBc third-harmonic distortion for a 1 V output. These characteristics make it suitable for systems that require both signal-to-noise performance and predictable gain calibration.
The dual-channel architecture provides separate high-impedance inputs and gain-control paths for each amplifier section. The 275 V/µs slew rate supports rapid amplitude transitions, while the wide bandwidth allows the device to process signals extending into the ultrasonic imaging range. Because the gain is voltage controlled, an external control voltage can support automatic gain control, attenuation, calibration, or signal-level normalization without mechanical adjustments.
Typical uses include ultrasound imaging receivers, medical ultrasound diagnostic equipment, dual-channel instrumentation, broadband signal analyzers, communication receivers, and precision test systems. In an ultrasound receiver, the AD600AQ can amplify weak echo signals while independent gain control supports channel-specific calibration and time-gain compensation. Its low noise is valuable when the gain must be increased enough to reveal signals close to the input noise floor.
Designers should use the manufacturer pin-description table to assign all 16 CERDIP connections and preserve the recommended dual-supply decoupling. Stable operation requires adequate bypass capacitance at the supply pins and careful grounding because high-speed signals can couple between the two channels. Gain-control voltage range, input impedance, output swing, and recommended source and load impedances should be taken directly from the manufacturer datasheet for the target board revision.
This page organizes the AD600AQ specifications, verified sourcing references, package information, a qualified AD602AQ comparison, and practical design guidance. The comparison is specifically limited to the same 16-lead CERDIP footprint, and any replacement should be checked against gain range, control-voltage behavior, bandwidth, supply voltage, pin assignments, temperature rating, and signal-integrity requirements before production use.
直接替换替代料: AD600AQ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
AD602AQ
✅ 直接替换📋 参考替代料(不在目录中)
AD600AQ 最大额定值与电气特性
| Number of Channels | 2 channels |
| Amplifier Type | Dual, low-noise, wideband variable gain amplifier |
| Gain Control | Independent voltage control per channel |
| Gain Response | Linear in dB |
| Gain Range | Up to +30 dB |
| Absolute Gain Accuracy | 0.3 dB |
| Input Noise Density | 1.4 nV/√Hz |
| Third-Harmonic Distortion | -60 dBc at 1 V output |
| Signal Bandwidth | 35 MHz at -3 dB |
| Slew Rate | 275 V/µs |
| Supply Voltage Range | ±4.75 V to ±5.25 V |
| 工作温度范围 | -40°C to +85°C |
| 封装 | 16-lead CERDIP (Q), 7.62 mm |
| 安装类型 | Through-hole |
| Technology | CMOS |
AD600AQ 16-lead cerdip (q), 7.62 mm 引脚配置指南
AD600AQ(16-lead cerdip (q), 7.62 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: AD600AQ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
AD600AQ 适用于 6 应用s: Medical Ultrasound Echo Amplification, Industrial Ultrasound Inspection, Wideband Automatic Gain Control, Instrumentation Signal Conditioning, Communications Receiver Front End, Precision Test and Measurement.
Medical Ultrasound Echo Amplification
The AD600AQ fits medical ultrasound echo receivers because each of its two channels provides independent voltage-controlled gain, a 1.4 nV/√Hz input-noise density, and a 35 MHz -3 dB bandwidth. The amplifier can sit between the transducer receiver circuitry and later processing stages, raising weak echo voltages while preserving the wideband information needed for time-of-flight measurement. Its +30 dB gain range and 0.3 dB absolute gain accuracy support controlled channel calibration. The main design consideration is that the two channels operate from separate ±4.75 V to ±5.25 V rails, requiring close supply bypassing and careful grounding.
推荐
Industrial Ultrasound Inspection
The AD600AQ is suitable for industrial ultrasonic inspection equipment that must recover small reflected signals across a wide frequency range. Its 35 MHz -3 dB bandwidth accommodates high-frequency echo content, while the 1.4 nV/√Hz input-noise density limits the input-referred noise that becomes dominant as gain increases. Independent gain control allows separate receive channels to be balanced for different probe paths or inspection sequences. The 275 V/µs slew rate supports rapid signal transitions, but the layout should keep gain-control routing away from sensitive inputs and use stable, low-impedance references for calibration.
推荐
Wideband Automatic Gain Control
The AD600AQ can implement a dual-channel automatic gain-control stage when both signal amplitude and control voltage are available to a feedback loop. Its linear-in-decibel response is useful because gain changes remain approximately proportional across a 30 dB operating interval, and the 0.3 dB absolute gain accuracy provides a defined calibration target. The 35 MHz bandwidth permits the loop to operate on high-frequency waveforms rather than only low-frequency envelopes. Designers should keep loop compensation separate from the analog input path and account for the amplifier's 275 V/µs slew rate when choosing detector and compensation components.
推荐
Instrumentation Signal Conditioning
The AD600AQ is appropriate for precision instrumentation that must condition two analog channels over a broad frequency range. Its low 1.4 nV/√Hz input-noise density, 0.3 dB gain accuracy, and -60 dBc third-harmonic distortion at a 1 V output are useful for sensors and receivers where amplitude integrity matters. Independent voltage control can support range switching, attenuation calibration, or normalization before digitization. The wide bandwidth must be matched by controlled board impedance and short return paths, while the dual-supply architecture should be decoupled at the device to limit noise on the rails.
推荐
Communications Receiver Front End
The AD600AQ can serve as a wideband receive-stage gain control element when two related channels require independent attenuation. The 35 MHz bandwidth is appropriate for broadband communication and test signals, while voltage-controlled gain simplifies automatic adjustment of signal levels. Low input noise supports operation near the receiver sensitivity limit, and the 0.3 dB absolute gain accuracy supports repeatable level adjustment. Because wideband gain stages can amplify interference as well as wanted signals, use a controlled ground reference, place bypass capacitors at the supply pins, and keep the gain-control traces away from high-impedance input nodes.
推荐
Precision Test and Measurement
The AD600AQ is useful in test systems requiring programmable attenuation or gain across two measurement channels. Its gain is controlled by voltage and has a linear-in-decibel response, simplifying many calibration tables, while the 1.4 nV/√Hz input-noise density supports low-level measurements. The 35 MHz bandwidth accommodates pulse and wideband test signals, and the 275 V/µs slew rate helps preserve amplitude during rapid transitions. For metrology-grade results, evaluate channel-to-channel gain matching against the 0.3 dB absolute accuracy figure, isolate the gain-control source, and calibrate the complete installed circuit rather than relying only on component-level values.
推荐
推荐产品汇总
工程参考数据: AD600AQ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD602AQ |
|---|---|---|
| Package | 16-lead CERDIP (Q), 7.62 mm | 16-lead CERDIP (Q), 7.62 mm |
| Brand | Analog Devices | Analog Devices |
| Number of Channels | 2 channels | 2 channels |
| Gain Control | Independent voltage control | Independent voltage control |
关键差异点
- Independent dual-channel gain adjustment (对比 AD602AQ)
- 35 MHz signal bandwidth (对比 AD602AQ)
- Low-noise dual-channel amplification (对比 AD602AQ)
- Defined gain accuracy and range (对比 AD602AQ)
设计说明
Place the positive and negative supply bypass capacitors immediately beside their corresponding AD600AQ pins. Keep the high-frequency return current within the smallest possible loop area and use a continuous ground reference beneath the signal path. The two amplifier channels are wideband and low-noise devices, so long supply traces and shared return paths can degrade channel isolation, output noise, and distortion even when the schematic is electrically correct.
Route the two high-impedance inputs as short and symmetrically terminated traces, and keep the independently controlled gain-input traces physically separated from the signal inputs. Reference the gain-control source to the same low-impedance ground used by the supply bypass network. Poor isolation between control and signal routes can couple modulation or switching artifacts into the amplified output even when the 1.4 nV/√Hz input-noise specification is met in the laboratory.
Do not treat the 16-lead CERDIP footprint as proof of electrical interchangeability. Before replacing the AD600AQ with the AD602AQ, compare gain range, gain-control voltage, supply requirements, bandwidth, noise, distortion, and every pin function against the manufacturer data for both devices. Also confirm that the ceramic package is suitable for the board's mechanical and soldering process; a package-compatible substitute can still fail if its electrical interface differs.
合规信息
The manufacturer product page and AD600AQ technical information do not state the requested environmental-compliance statuses. The industrial-temperature AD600A grade is not, by itself, an AEC-Q100 automotive qualification.