Analog Devices

AD600AQ - Dual 35MHz Low-Noise VGA | Analog Devices

MPN: AD600AQ ✓ Aktif
±4.75 V to ±5.25 V Vdss 16-lead CERDIP (Q), 7.62 mm Package
MOQ: 1 |

AD600AQ Genel Bakış

Analog Devices AD600AQ is a dual-channel, low-noise, wideband variable gain amplifier with independent gain control, a 35 MHz -3 dB bandwidth, and a 1.4 nV/√Hz input-noise density, housed in a 16-lead CERDIP (Q) package. Each channel provides a linear-in-decibel gain response, a gain range up to +30 dB, absolute gain accuracy of 0.3 dB, and low distortion. The device operates from dual ±4.75 V to ±5.25 V supplies and is specified from -40°C to +85°C.

A variable gain amplifier, or VGA, is an analog signal-conditioning amplifier whose gain is adjusted by an external control voltage. Its position in the signal chain is between a low-level source and a downstream measurement, imaging, or conversion stage. The AD600 belongs to the broader hierarchy of voltage-controlled amplifiers, instrumentation amplifiers, analog amplifiers, and integrated analog circuits. Independent channel control allows two signal paths to be adjusted separately, which is valuable when two ultrasound echo channels require different gains or calibrated attenuation.

The AD600AQ combines a 1.4 nV/√Hz input-noise density with a 35 MHz -3 dB bandwidth and gain accuracy of 0.3 dB. Its linear-in-decibel control characteristic helps maintain consistent amplitude behavior across a broad gain range. The amplifier also supports low-distortion operation, with the manufacturer data listing -60 dBc third-harmonic distortion for a 1 V output. These characteristics make it suitable for systems that require both signal-to-noise performance and predictable gain calibration.

The dual-channel architecture provides separate high-impedance inputs and gain-control paths for each amplifier section. The 275 V/µs slew rate supports rapid amplitude transitions, while the wide bandwidth allows the device to process signals extending into the ultrasonic imaging range. Because the gain is voltage controlled, an external control voltage can support automatic gain control, attenuation, calibration, or signal-level normalization without mechanical adjustments.

Typical uses include ultrasound imaging receivers, medical ultrasound diagnostic equipment, dual-channel instrumentation, broadband signal analyzers, communication receivers, and precision test systems. In an ultrasound receiver, the AD600AQ can amplify weak echo signals while independent gain control supports channel-specific calibration and time-gain compensation. Its low noise is valuable when the gain must be increased enough to reveal signals close to the input noise floor.

Designers should use the manufacturer pin-description table to assign all 16 CERDIP connections and preserve the recommended dual-supply decoupling. Stable operation requires adequate bypass capacitance at the supply pins and careful grounding because high-speed signals can couple between the two channels. Gain-control voltage range, input impedance, output swing, and recommended source and load impedances should be taken directly from the manufacturer datasheet for the target board revision.

This page organizes the AD600AQ specifications, verified sourcing references, package information, a qualified AD602AQ comparison, and practical design guidance. The comparison is specifically limited to the same 16-lead CERDIP footprint, and any replacement should be checked against gain range, control-voltage behavior, bandwidth, supply voltage, pin assignments, temperature rating, and signal-integrity requirements before production use.

Drop-in alternatifler için AD600AQ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

AD602AQ

✅ Yerleştirme
📦 16-lead CERDIP (Q), 7.62 mm
Same 16-lead CERDIP footprint and two independent channels; the AD602AQ uses a different gain-programming characteristic from the AD600AQ's +30 dB range, requiring control-interface validation.

📋 Katalogda Olmayan Referans Alternatifi

AD600AQ Maksimum Değerlendirmeler & Elektriksel Özellikler

Number of Channels 2 channels
Amplifier Type Dual, low-noise, wideband variable gain amplifier
Gain Control Independent voltage control per channel
Gain Response Linear in dB
Gain Range Up to +30 dB
Absolute Gain Accuracy 0.3 dB
Input Noise Density 1.4 nV/√Hz
Third-Harmonic Distortion -60 dBc at 1 V output
Signal Bandwidth 35 MHz at -3 dB
Slew Rate 275 V/µs
Supply Voltage Range ±4.75 V to ±5.25 V
İşletim Sıcaklığı Aralığı -40°C to +85°C
Paket 16-lead CERDIP (Q), 7.62 mm
Montaj Türü Through-hole
Technology CMOS

AD600AQ 16-lead cerdip (q), 7.62 mm Pin Yapısı Kılavuzu

AD600AQ (16-lead cerdip (q), 7.62 mm paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.

16-lead cerdip (q), 7.62 mm paket pin çizelgesi için AD600AQ

Ayrıntılı pin çıkış verisi mevcut değil: AD600AQ.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

AD600AQ için uygundur 6 uygulamas: Medical Ultrasound Echo Amplification, Industrial Ultrasound Inspection, Wideband Automatic Gain Control, Instrumentation Signal Conditioning, Communications Receiver Front End, Precision Test and Measurement.

💊

Medical Ultrasound Echo Amplification

The AD600AQ fits medical ultrasound echo receivers because each of its two channels provides independent voltage-controlled gain, a 1.4 nV/√Hz input-noise density, and a 35 MHz -3 dB bandwidth. The amplifier can sit between the transducer receiver circuitry and later processing stages, raising weak echo voltages while preserving the wideband information needed for time-of-flight measurement. Its +30 dB gain range and 0.3 dB absolute gain accuracy support controlled channel calibration. The main design consideration is that the two channels operate from separate ±4.75 V to ±5.25 V rails, requiring close supply bypassing and careful grounding.

🏭

Industrial Ultrasound Inspection

The AD600AQ is suitable for industrial ultrasonic inspection equipment that must recover small reflected signals across a wide frequency range. Its 35 MHz -3 dB bandwidth accommodates high-frequency echo content, while the 1.4 nV/√Hz input-noise density limits the input-referred noise that becomes dominant as gain increases. Independent gain control allows separate receive channels to be balanced for different probe paths or inspection sequences. The 275 V/µs slew rate supports rapid signal transitions, but the layout should keep gain-control routing away from sensitive inputs and use stable, low-impedance references for calibration.

⚡

Wideband Automatic Gain Control

The AD600AQ can implement a dual-channel automatic gain-control stage when both signal amplitude and control voltage are available to a feedback loop. Its linear-in-decibel response is useful because gain changes remain approximately proportional across a 30 dB operating interval, and the 0.3 dB absolute gain accuracy provides a defined calibration target. The 35 MHz bandwidth permits the loop to operate on high-frequency waveforms rather than only low-frequency envelopes. Designers should keep loop compensation separate from the analog input path and account for the amplifier's 275 V/µs slew rate when choosing detector and compensation components.

🔧

Instrumentation Signal Conditioning

The AD600AQ is appropriate for precision instrumentation that must condition two analog channels over a broad frequency range. Its low 1.4 nV/√Hz input-noise density, 0.3 dB gain accuracy, and -60 dBc third-harmonic distortion at a 1 V output are useful for sensors and receivers where amplitude integrity matters. Independent voltage control can support range switching, attenuation calibration, or normalization before digitization. The wide bandwidth must be matched by controlled board impedance and short return paths, while the dual-supply architecture should be decoupled at the device to limit noise on the rails.

🌐

Communications Receiver Front End

The AD600AQ can serve as a wideband receive-stage gain control element when two related channels require independent attenuation. The 35 MHz bandwidth is appropriate for broadband communication and test signals, while voltage-controlled gain simplifies automatic adjustment of signal levels. Low input noise supports operation near the receiver sensitivity limit, and the 0.3 dB absolute gain accuracy supports repeatable level adjustment. Because wideband gain stages can amplify interference as well as wanted signals, use a controlled ground reference, place bypass capacitors at the supply pins, and keep the gain-control traces away from high-impedance input nodes.

🖥️

Precision Test and Measurement

The AD600AQ is useful in test systems requiring programmable attenuation or gain across two measurement channels. Its gain is controlled by voltage and has a linear-in-decibel response, simplifying many calibration tables, while the 1.4 nV/√Hz input-noise density supports low-level measurements. The 35 MHz bandwidth accommodates pulse and wideband test signals, and the 275 V/µs slew rate helps preserve amplitude during rapid transitions. For metrology-grade results, evaluate channel-to-channel gain matching against the 0.3 dB absolute accuracy figure, isolate the gain-control source, and calibrate the complete installed circuit rather than relying only on component-level values.

Önerilen Ürünler Özeti

AD600AQ Analog Devices Kullanıldığı Yer: Medical Ultrasound Echo Amplification, Industrial Ultrasound Inspection, Wideband Automatic Gain Control, Instrumentation Signal Conditioning, Communications Receiver Front End, Precision Test and Measurement AD602AQ Same-family variable gain amplifier option Kullanıldığı Yer: Medical Ultrasound Echo Amplification, Industrial Ultrasound Inspection, Wideband Automatic Gain Control, Instrumentation Signal Conditioning, Communications Receiver Front End, Precision Test and Measurement
What is the AD600AQ?
The AD600AQ is a dual-channel, low-noise, wideband variable gain amplifier from Analog Devices. Each channel has independent voltage-based gain control, a linear-in-decibel response, and up to +30 dB gain. According to the manufacturer data, the device combines a 1.4 nV/√Hz input-noise density with 35 MHz -3 dB bandwidth in a 16-lead CERDIP package.
What are the key specifications of AD600AQ?
The AD600AQ provides two independently controlled amplifier channels, +30 dB maximum gain, 0.3 dB absolute gain accuracy, and a 35 MHz -3 dB bandwidth. The manufacturer data also specifies 1.4 nV/√Hz input noise, -60 dBc third-harmonic distortion at a 1 V output, a 275 V/µs slew rate, and operation from dual ±4.75 V to ±5.25 V supplies.
What is the bandwidth and noise performance of AD600AQ?
The AD600AQ has a 35 MHz -3 dB signal bandwidth and a 1.4 nV/√Hz input-noise density. These two specifications make it suitable for processing weak, wideband signals where amplification must preserve useful bandwidth without raising the input noise floor excessively. The manufacturer data also identifies the AD600 family as being optimized for ultrasound imaging.
What supply voltage does AD600AQ require?
The AD600AQ operates from dual ±4.75 V to ±5.25 V supplies. Because the circuit contains two amplifier channels, each rail must be decoupled close to the device, and the layout should return high-frequency currents through a compact ground path. The manufacturer data identifies the technology as CMOS and the AD600A temperature grade as -40°C to +85°C.
Where can I download the AD600AQ datasheet PDF?
The official AD600AQ documentation is available through the Analog Devices AD600 product page at https://www.analog.com/en/products/ad600.html. The manufacturer data sheet contains the recommended applications, electrical characteristics, pin assignments, and operating information. Use the AD600AQ ordering-code information when selecting the 16-lead CERDIP industrial-temperature version.
Where can I find the AD600AQ pinout?
The AD600AQ uses a 16-lead CERDIP (Q) package, and its complete pin assignments are shown in the manufacturer AD600 data sheet and pin-description table. Assign the two channels, their gain-control inputs, positive and negative supply connections, and grounds strictly from that table. The same package drawing also applies to the compared AD602AQ, but verify control-voltage behavior before substituting it.
Is AD600AQ suitable for ultrasound imaging?
Yes, the AD600AQ is suitable for ultrasound imaging because its low-noise dual-channel architecture, 35 MHz -3 dB bandwidth, and independent gain control align with multi-channel echo-amplifier requirements. The 1.4 nV/√Hz input-noise density is particularly useful when the receiver operates at high gain, while separate channel controls permit calibration or time-gain-compensation strategies.
How does gain control work in the AD600AQ?
The AD600AQ uses a separate external control voltage for each amplifier channel, and its gain response is linear in decibels. The listed gain range extends to +30 dB with an absolute gain accuracy of 0.3 dB. This permits software- or analog-driven adjustment in ultrasound receivers, automatic gain-control loops, laboratory attenuators, and calibrated measurement systems.
AD600AQ vs AD602AQ: which is better for ultrasound receivers?
The AD600AQ is the better default choice when a gain range up to +30 dB and a 35 MHz bandwidth satisfy the receiver design. The AD602AQ is a same-family, 16-lead CERDIP alternative, but its gain range and control characteristics should be compared with the channel requirements of the ultrasound system. Both devices use independent dual-channel voltage control, while the AD602AQ offers a different gain-programming option.
What is the difference between AD600AQ and AD602AQ?
Both parts are dual-channel variable gain amplifiers in the 16-lead CERDIP package and use independent voltage-controlled gain adjustment. The principal engineering difference is the gain-programming characteristic: the AD600AQ supports the listed +30 dB range, while the AD602AQ provides a different maximum-gain and control-voltage arrangement. Confirm bandwidth, distortion, supply requirements, and every pin function before interchange.
When should I choose AD600AQ over AD602AQ?
Choose the AD600AQ when the system requires a gain range up to +30 dB and the application is designed around the AD600 control-voltage interface. Choose the AD602AQ when its alternative gain range better matches the receiver or measurement chain and its control-voltage behavior can be integrated with the surrounding circuitry. Both can preserve the same CERDIP footprint, but they are not automatically interchangeable without functional validation.
Is AD600AQ suitable for medical diagnostic equipment?
The AD600AQ fits the signal-conditioning requirements of medical ultrasound diagnostic systems because it is optimized for ultrasound imaging, offers independent dual-channel gain control, and combines low noise with wide bandwidth. The -40°C to +85°C industrial temperature rating is distinct from any medical-product qualification requirement, so the finished equipment must still complete its applicable safety and validation process.
What is the best drop-in replacement for AD600AQ?
The AD602AQ is the closest identified same-package alternative because it uses the 16-lead CERDIP (Q) footprint and provides two independently controlled variable gain amplifier channels. It is not a universal substitute: its gain range and control-voltage interface must match the original circuit, and all supply, timing, and signal-integrity requirements need verification. Request manufacturer-confirmed sourcing through the Request a Quote form on this page.
Can AD602AQ replace AD600AQ without changing the PCB?
The AD602AQ can retain the same 16-lead CERDIP PCB footprint, but physical compatibility does not by itself guarantee electrical drop-in operation. Review its gain range, gain-control voltage, bandwidth, noise, slew rate, distortion, supply pins, and power-up behavior against the AD600AQ design. Use the manufacturer data for both parts to approve the substitution before production.
Where can I buy AD600AQ, and what is its price and lead time?
Use the Request a Quote form on this page to request AD600AQ pricing, current availability, minimum order quantity, and production lead time. The commercial module presents the current sourcing response without a static price that could become outdated. Provide the required 16-lead CERDIP package, industrial-temperature grade, quantity, and target delivery schedule in the request.
What is the best cross-brand equivalent for AD600AQ?
No cross-brand drop-in equivalent is established by the available manufacturer and cross-reference information for the 16-lead CERDIP AD600AQ. A replacement must match the complete pin arrangement, dual-supply requirement, gain-control interface, bandwidth, noise, and distortion specifications. Request a manufacturer-confirmed cross-brand recommendation through the Request a Quote form rather than substituting solely on bandwidth or package name.
Can I use AD600AQ in a dual-channel signal-level controller?
Yes, the two independent gain-control channels of the AD600AQ support dual-channel signal-level control, calibration, or attenuation. Its 0.3 dB absolute gain accuracy, linear-in-decibel response, and 35 MHz bandwidth are useful when the two channels must remain predictable over a broad signal range. The external control circuitry and feedback strategy must avoid exceeding the manufacturer control-voltage limits.

Mühendislik referans verileri: AD600AQ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the AD600AQ for dual-channel ultrasound, instrumentation, or communications designs requiring independent voltage-controlled gain, a gain range up to +30 dB, a 35 MHz -3 dB bandwidth, and a 1.4 nV/√Hz input-noise density. It is particularly appropriate when the existing design uses the 16-lead CERDIP package and requires the -40°C to +85°C industrial temperature grade. The AD602AQ retains the same package and dual-channel architecture, so it is the relevant alternative when its different gain-programming characteristic better matches the receiver's control interface. Confirm control voltages, pin functions, bandwidth, distortion, noise, and supply requirements before replacing the AD600AQ. No cross-brand drop-in option is established, and functional substitutes should not be selected solely because they are described as low-noise VGAs.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün AD602AQ
Package 16-lead CERDIP (Q), 7.62 mm 16-lead CERDIP (Q), 7.62 mm
Brand Analog Devices Analog Devices
Number of Channels 2 channels 2 channels
Gain Control Independent voltage control Independent voltage control

Ana Farklılayıcılar

  • Independent dual-channel gain adjustment (karşılaştırma:AD602AQ)
  • 35 MHz signal bandwidth (karşılaştırma:AD602AQ)
  • Low-noise dual-channel amplification (karşılaştırma:AD602AQ)
  • Defined gain accuracy and range (karşılaştırma:AD602AQ)

Tasarım Notları

Place the positive and negative supply bypass capacitors immediately beside their corresponding AD600AQ pins. Keep the high-frequency return current within the smallest possible loop area and use a continuous ground reference beneath the signal path. The two amplifier channels are wideband and low-noise devices, so long supply traces and shared return paths can degrade channel isolation, output noise, and distortion even when the schematic is electrically correct.

Route the two high-impedance inputs as short and symmetrically terminated traces, and keep the independently controlled gain-input traces physically separated from the signal inputs. Reference the gain-control source to the same low-impedance ground used by the supply bypass network. Poor isolation between control and signal routes can couple modulation or switching artifacts into the amplified output even when the 1.4 nV/√Hz input-noise specification is met in the laboratory.

Do not treat the 16-lead CERDIP footprint as proof of electrical interchangeability. Before replacing the AD600AQ with the AD602AQ, compare gain range, gain-control voltage, supply requirements, bandwidth, noise, distortion, and every pin function against the manufacturer data for both devices. Also confirm that the ceramic package is suitable for the board's mechanical and soldering process; a package-compatible substitute can still fail if its electrical interface differs.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The manufacturer product page and AD600AQ technical information do not state the requested environmental-compliance statuses. The industrial-temperature AD600A grade is not, by itself, an AEC-Q100 automotive qualification.

Veri doğrulanma tarihi: 2026-11-14 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

AD600AQ datasheet AD600AQ pinout AD600AQ datasheet pdf AD600AQ specifications AD600AQ 16 lead CERDIP AD600AQ variable gain amplifier AD600AQ ultrasound amplifier AD600AQ vs AD602AQ AD600AQ drop-in replacement AD600AQ equivalent Analog Devices AD600AQ AD600AQ price AD600AQ stock AD600AQ application circuit

İlgili Bileşenler ve Terimler

Analog Devices AD600AQ AD602AQ dual variable gain amplifier variable gain amplifier voltage-controlled amplifier X-AMP instrumentation amplifier analog amplifier integrated circuit semiconductor linear-in-decibel gain response input noise density absolute gain accuracy signal bandwidth slew rate third-harmonic distortion 16-lead CERDIP CERDIP package family through-hole mounting ultrasound imaging medical diagnostic equipment industrial ultrasonic inspection automatic gain control RoHS REACH AEC-Q100 JEDEC IPC IEC IEEE UL ISO
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle