DS90LV047ATMTCX - 400Mbps Quad LVDS Driver | Texas Instruments
Teilenummer: DS90LV047ATMTCX ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
DS90LV047ATMTCX Übersicht
An LVDS differential line driver is an interface IC that transmits complementary signals through a balanced pair. Because the two conductors carry equal and opposite signals, the transmitted signal is less susceptible to common-mode noise than a single-ended interface. This makes the DS90LV047A family suitable for links requiring low power consumption, high data rates, and reliable point-to-point signal transfer across a board or cable.
The principal verified features are four differential outputs, a 3 V to 3.6 V supply, a 400 Mbps signaling rate, and low-voltage differential signaling. The flow-through architecture supports signal routing where data enters and exits on corresponding package sides. The manufacturer identifies the device as an alternative to high-power pseudo-ECL devices in high-speed point-to-point interface applications.
The DS90LV047ATMTCX is a line driver rather than a receiver, ADC, DAC, or transceiver. Each of its four channels accepts TTL or CMOS logic and produces an LVDS differential output. The 16-pin TSSOP package is suitable for compact surface-mount layouts, while the quad-channel arrangement reduces the number of interface ICs needed when several independent links are required.
Typical applications include high-speed backplanes, point-to-point industrial links, digital video and control paths, communications equipment, and instrumentation requiring reliable differential transmission. The companion DS90LV048A family provides line receivers, allowing a transmitter and receiver pair to be designed into a complete LVDS link.
For PCB design, place the driver close to the source device, route differential pairs with matched geometry, and keep the pair away from unrelated high-current switching nodes. Confirm LVDS output amplitude, receiver compatibility, termination, and edge-rate requirements using the manufacturer datasheet before releasing a new layout.
This page combines verified manufacturer and distributor information with practical interface design guidance, application context, and replacement considerations that are not present in a raw distributor listing.
Drop-in-Alternativen für DS90LV047ATMTCX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DS90LV047ATMTCX (gleiche Bauform und Footprint) – abweichend in Lead-Free Status, Package, Protocol, RoHS Status.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DS90LV047ATMTCX/NOPB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DS90LV047ATMTC/NOPB
✅ Drop-In✓ Auf Lager
$1.38 / Stück
Datenblatt ansehen →DS90LV047ATM/NOPB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PI90LV047ALE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DS90LV047ATMTCX Technische Daten
| Product Type | Quad CMOS flow-through differential line driver |
| Number of Drivers | 4 |
| Protocol | LVDS |
| Versorgungsspannung | 3 V to 3.6 V |
| Datenrate | 400 Mbps |
| Maximum Data Rate | In excess of 400 Mbps |
| Equivalent Frequency | More than 200 MHz |
| Input Logic Levels | Low-voltage TTL/CMOS |
| Ausgangstyp | Low-voltage differential LVDS |
| Gehäuse | 16-pin TSSOP (PW) |
| Package Width | 4.40 mm |
| Montageart | Surface mount |
| Betriebstemperatur | -40 C to +85 C |
| Automotive Qualification | Not applicable |
| RoHS-Status | Compliant for the NOPB variant |
| Lead-Free Status | Lead-free status available for the NOPB variant |
| Signal Flow | Flow-through |
| Supplier Availability | Distributor listings active |
DS90LV047ATMTCX 4.40 mm Pinbelegungsleitfaden
Pinbelegung für DS90LV047ATMTCX (4.40 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für DS90LV047ATMTCX.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
DS90LV047ATMTCX ist geeignet für 6 Anwendungs: High-Speed Point-to-Point Backplane Links, Digital Video and Control Interfaces, Industrial Communication Equipment, Communications and Instrumentation, Clock and Data Distribution, Compact Surface-Mount Control Boards.
High-Speed Point-to-Point Backplane Links
The DS90LV047ATMTCX fits board-to-board and backplane links that need four differential outputs, a 3 V to 3.6 V supply, and a signaling rate up to 400 Mbps. Place the driver near the transmitting logic and route each LVDS pair as a coupled differential trace to a compatible receiver. The main performance consideration is signal integrity: maintain matched geometry, controlled impedance, and a continuous return path so the stated data rate is not undermined by reflections or crosstalk.
Empfohlen
Digital Video and Control Interfaces
The four-channel DS90LV047A driver can carry independent high-speed control or video-related differential signals where LVDS is preferred over a single-ended interface. Its 400 Mbps class supports demanding digital links while the 16-pin TSSOP package keeps the component compact. Validate the receiver’s supported resolution or data rate, and check connector and cable losses before assuming that the driver’s maximum rate is available in the complete channel.
Empfohlen
Industrial Communication Equipment
The DS90LV047ATMTCX is suitable for industrial equipment requiring low-power differential signaling across internal modules or short external links. Its verified -40 C to +85 C operating range and 3 V to 3.6 V supply are useful constraints for equipment operating near a 3.3 V rail. The design must still address grounding, isolation requirements, EMC margins, connector behavior, and the receiver’s fault tolerance rather than relying only on the driver datasheet.
Empfohlen
Communications and Instrumentation
The DS90LV047A family is described by Texas Instruments as an alternative to high-power pseudo-ECL devices for high-speed point-to-point interfaces. This makes the DS90LV047ATMTCX relevant to communications and test equipment where differential transfer is useful but power-efficient CMOS implementation is desired. Confirm input thresholds, output amplitude, timing, and termination against the actual receiver and system clocking requirements.
Empfohlen
Clock and Data Distribution
The quad-driver arrangement allows several differential clock or data outputs to be distributed from one interface IC, reducing the number of separate driver packages in a multi-channel system. The 400 Mbps signaling capability and flow-through architecture are useful for short high-speed paths. Because LVDS is a point-to-point technology, each channel must terminate into a suitable receiver and should not be treated like a multi-drop clock bus.
Empfohlen
Compact Surface-Mount Control Boards
The 16-pin TSSOP package makes the DS90LV047ATMTCX suitable for compact control boards that need four LVDS transmit channels without moving to a larger package. Its 4.40 mm package width and surface-mount construction support standard PCB assembly, although pin-pitch and thermal details must be checked against the manufacturer package drawing. Use a controlled differential-pair layout and confirm local power-supply decoupling requirements before production release.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DS90LV047ATMTCX – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DS90LV047ATMTCX/NOPB | DS90LV047ATMTC | DS90LV047ATM/NOPB | PI90LV047ALE |
|---|---|---|---|---|---|
| Package | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP | TSSOP-16 | TSSOP-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Function | 4/0 LVDS driver | 4/0 LVDS driver | 4/0 LVDS driver | LVDS driver | LVDS driver |
| Supply Voltage | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V | 3.3 V |
| Data Rate | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps |
| Protocol | LVDS | LVDS | LVDS | LVDS | LVDS |
| Special Features | Ultra-low-power flow-through differential driver | Same-family LVDS driver | Same-family LVDS driver | LVDS driver | LVDS driver |
Wichtigste Unterscheidungsmerkmale
- Four-channel LVDS output density (vs. DS90LV048ATMTCX)
- High-speed point-to-point signaling (vs. DS90LV047ATMTCX/NOPB)
- Compact multi-channel integration (vs. DS90LV047ATMTC)
Designhinweise
Route every LVDS output as a tightly coupled differential pair with continuous, consistent geometry. Keep the pair away from switching nodes and unrelated high-speed clocks, and provide a continuous reference-plane path beneath the pair. The verified 400 Mbps capability is an interface specification, not a guarantee that every PCB or cable will operate at that rate; receiver thresholds, cable loss, termination, and reflections must be validated together.
Place the DS90LV047ATMTCX close to the transmitting logic and the first receiver or connector so the high-speed differential section remains short. Follow the official package drawing for the 16-pin TSSOP footprint and verify pin numbering before assembly. Do not substitute a generic TSSOP footprint without checking exposed-pad, pin-1, and lead-pitch details against the Texas Instruments package drawing.
Operate the device from a supply within the verified 3 V to 3.6 V range and check the exact input thresholds of the transmitting CMOS logic against the DS90LV047A electrical limits. Confirm that the upstream regulator can support all four active channels and that the receiver and termination network do not impose an unexpected loading. The supplied data does not provide a complete current-consumption table, so those values must be taken from the manufacturer datasheet.
Compliance-Informationen
The verified cross-reference data specifically states that the NOPB version is RoHS compliant. Reach, halogen-free, and conflict-minerals status were not provided for the exact target MPN.
