DSPIC30F6010T-30I/PF - 30 MIPS 16-bit DSC 144KB Flash | Microchip
Teilenummer: DSPIC30F6010T-30I/PF ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.2 | $132,00 |
| 100 | $11.85 | $1.185,00 |
| 500 | $10.4 | $5.200,00 |
| 1.000 | $9.15 | $9.150,00 |
DSPIC30F6010T-30I/PF Übersicht
A Digital Signal Controller is a hybrid architecture that combines the deterministic interrupt response and peripheral set of a microcontroller with the computational throughput of a Digital Signal Processor. Within the broader hierarchy of semiconductor devices, a DSC sits between an 8-bit/16-bit MCU (general control) and a full DSP (streaming numeric compute), making it well suited for embedded motor control, power conversion, sensor conditioning and audio processing where both tight loop control and DSP-class math are required on the same silicon.
Key features of the DSPIC30F6010T-30I/PF include its modified Harvard architecture with a 16-bit native datapath and dual 40-bit accumulators for DSP operations, a built-in single-cycle MAC engine, on-chip 10-bit/12-bit ADC capability (12-bit at 200 ksps or 10-bit at 1 Msps, depending on variant configuration), multiple PWM modules with duty cycle resolution suitable for 3-phase motor control, and a rich set of peripherals such as UART, SPI, I2C, CAN, DCI and quadrature encoder interfaces that let designers build a complete 3-phase inverter or DSP codec on a single IC.
Architecturally, the device uses a 24-bit instruction word (hence the 48K x 24 flash organization) so each instruction can carry a literal and an address together, which contributes to the controller's deterministic cycle count and code density. The internal PLL allows the part to operate from a wide range of external crystals while still hitting the full 30 MIPS internal clock, and the 2.5V-5.5V VDD range covers both 3.3V and 5V system rails without external level translation.
Typical applications include 3-phase AC induction and BLDC/PMSM motor drives, digital uninterruptible power supplies (UPS) and power factor correction stages, audio processing front-ends, automotive sensor conditioning, industrial control DSP loops, and consumer appliance inverter boards. The wide peripheral set also makes it a frequent choice for digital PLL, digital filter and high-speed PID implementations where a small MCU would lack the bandwidth and a full DSP would lack the deterministic interrupt latency.
When designing with this part, allocate decoupling capacitors close to every VDD/VSS pair and follow Microchip's recommended layout for the TQFP-80 exposed-pad variant to keep thermal resistance within the 14x14 mm package's rated Theta-JA. Also note that the 'T' suffix in the MPN denotes Tape and Reel packaging and 'I' indicates the industrial -40C to +85C operating range; the 'PF' suffix specifies the 80-pin TQFP package.
This page synthesizes distributor pricing, drop-in pin-compatible alternatives and practical design notes that are not found in the manufacturer datasheet alone, and is intended to accelerate BOM selection, second-sourcing and lifecycle risk management for the DSPIC30F6010T-30I/PF.
Drop-in-Alternativen für DSPIC30F6010T-30I/PF – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit DSPIC30F6010T-30I/PF (gleiche Bauform und Footprint) – abweichend in Operating Temperature, Package, Core Architecture, ADC, Maximum CPU Speed.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
DSPIC30F6010A-30I/PF
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC30F6010-30I/PF
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC30F6010AT-30I/PF
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
DSPIC30F6010T-20I/PF
✅ Drop-In✓ Auf Lager
$6.85 / Stück
Datenblatt ansehen →DSPIC30F6010T-20E/PF
✅ Drop-In✓ Auf Lager
$7.78 / Stück
Datenblatt ansehen →DSPIC30F6010-20E/PF
✅ Drop-In✓ Auf Lager
$8.97 / Stück
Datenblatt ansehen →DSPIC30F6010T-30I/PF Grenzwerte & elektrische Eigenschaften
| Product Type | Digital Signal Controller (DSC) |
| Core Architecture | dsPIC30F (16-bit DSC, modified Harvard) |
| CPU Instruction Width | 24-bit |
| Maximum CPU Speed | 30 MIPS |
| Maximale Taktfrequenz | 40 MHz |
| Program Memory (Flash) | 144 KB (48K x 24) |
| Data RAM | 8 KB |
| Data EEPROM | 4 KB |
| Supply Voltage (VDD) | 2.5 V to 5.5 V |
| Betriebstemperatur | -40 C to +85 C (Industrial) |
| Gehäuse | 80-pin TQFP (PF), 14x14 mm, 0.65 mm pitch |
| Montageart | Surface Mount |
| ADC | 12-bit @ 200 ksps / 10-bit @ 1 Msps (variant-dependent) |
| DSP Engine | Single-cycle MAC with dual 40-bit accumulators |
| RoHS-Status | Compliant |
DSPIC30F6010T-30I/PF Pin-Konfiguration
| Pin 1 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| Pin 2 | OSC2/CLKOUT — Oscillator crystal output / system clock output |
| Pin 3 | MCLR — Master Clear (reset) input |
| Pin 4 | VSS — Ground reference |
| Pin 5 | VDD — Positive supply voltage (2.5 V - 5.5 V) |
| Pin 6 | PGED1/EMUD1 — ICSP programming data / ICD emulation data |
| Pin 7 | PGEC1/EMUC1 — ICSP programming clock / ICD emulation clock |
| Pin 8 | FLTA — PWM fault input A |
| Pin 9 | PWM1H — PWM1 high-side output |
| Pin 10 | PWM1L — PWM1 low-side output |
| Pin 11 | PWM2H — PWM2 high-side output |
| Pin 12 | PWM2L — PWM2 low-side output |
| Pin 13 | PWM3H — PWM3 high-side output |
| Pin 14 | PWM3L — PWM3 low-side output |
| Pin 15 | PWM4H — PWM4 high-side output |
| Pin 16 | PWM4L — PWM4 low-side output |
| Pin 17 | PWM5H — PWM5 high-side output |
| Pin 18 | PWM5L — PWM5 low-side output |
| Pin 19 | PWM6H — PWM6 high-side output |
| Pin 20 | PWM6L — PWM6 low-side output |
| Pin 21 | VSS — Ground reference |
| Pin 22 | VDD — Positive supply voltage (2.5 V - 5.5 V) |
| Pin 23 | AN0 — Analog input 0 / ADC input |
| Pin 24 | AN1 — Analog input 1 / ADC input |
| Pin 25 | AN2 — Analog input 2 / ADC input |
| Pin 26 | AN3 — Analog input 3 / ADC input |
| Pin 27 | AN4 — Analog input 4 / ADC input |
| Pin 28 | AN5 — Analog input 5 / ADC input |
| Pin 29 | AN6 — Analog input 6 / ADC input |
| Pin 30 | AN7 — Analog input 7 / ADC input |
| Pin 31 | AN8 — Analog input 8 / ADC input |
| Pin 32 | AN9 — Analog input 9 / ADC input |
| Pin 33 | AN10 — Analog input 10 / ADC input |
| Pin 34 | AN11 — Analog input 11 / ADC input |
| Pin 35 | AN12 — Analog input 12 / ADC input |
| Pin 36 | AN13 — Analog input 13 / ADC input |
| Pin 37 | AN14 — Analog input 14 / ADC input |
| Pin 38 | AN15 — Analog input 15 / ADC input |
| Pin 39 | VREF- — ADC voltage reference low |
| Pin 40 | VREF+ — ADC voltage reference high |
| Pin 41 | AVSS — Analog ground |
| Pin 42 | AVDD — Analog positive supply |
| Pin 43 | QEA — Quadrature encoder A input |
| Pin 44 | QEB — Quadrature encoder B input |
| Pin 45 | INDX — Quadrature encoder index input |
| Pin 46 | HOME — Home position input |
| Pin 47 | FLTB — PWM fault input B |
| Pin 48 | C1RX — CAN1 receive input |
| Pin 49 | C1TX — CAN1 transmit output |
| Pin 50 | C2RX — CAN2 receive input |
| Pin 51 | C2TX — CAN2 transmit output |
| Pin 52 | U1RX — UART1 receive |
| Pin 53 | U1TX — UART1 transmit |
| Pin 54 | U2RX — UART2 receive |
| Pin 55 | U2TX — UART2 transmit |
| Pin 56 | SDI1 — SPI1 data input |
| Pin 57 | SDO1 — SPI1 data output |
| Pin 58 | SCK1 — SPI1 clock |
| Pin 59 | SS1 — SPI1 slave select |
| Pin 60 | SDA1 — I2C1 data |
| Pin 61 | SCL1 — I2C1 clock |
| Pin 62 | T1CK — Timer1 external clock |
| Pin 63 | T2CK — Timer2 external clock |
| Pin 64 | T3CK — Timer3 external clock |
| Pin 65 | IC1 — Input capture 1 |
| Pin 66 | IC2 — Input capture 2 |
| Pin 67 | IC3 — Input capture 3 |
| Pin 68 | OC1 — Output compare 1 |
| Pin 69 | OC2 — Output compare 2 |
| Pin 70 | OC3 — Output compare 3 |
| Pin 71 | INT0 — External interrupt 0 |
| Pin 72 | INT1 — External interrupt 1 |
| Pin 73 | INT2 — External interrupt 2 |
| Pin 74 | INT3 — External interrupt 3 |
| Pin 75 | INT4 — External interrupt 4 |
| Pin 76 | RA0 — GPIO port A bit 0 |
| Pin 77 | RA1 — GPIO port A bit 1 |
| Pin 78 | RB0 — GPIO port B bit 0 |
| Pin 79 | RB1 — GPIO port B bit 1 |
| Pin 80 | VSS — Ground reference |
Typische Anwendungen
DSPIC30F6010T-30I/PF ist geeignet für 6 Anwendungs: 3-Phase BLDC / PMSM Motor Drive (FOC), Digital Uninterruptible Power Supply (UPS) / PFC, Industrial Sensor Signal Conditioning / DSP Front-End, Audio Processing / Codec Interface, Automotive Sensor and Actuator Control, Consumer Appliance Inverter Board.
3-Phase BLDC / PMSM Motor Drive (FOC)
The DSPIC30F6010T-30I/PF is a long-standing workhorse for field-oriented control of 3-phase BLDC and PMSM motors in industrial drives and appliance inverters. Its 30 MIPS CPU, 6-channel PWM with dead-time control, quadrature encoder interface (QEI), 12-bit 200 ksps ADC and dual 40-bit accumulators with single-cycle MAC deliver the deterministic control loop bandwidth required for sinusoidal FOC at typical 8-20 kHz PWM frequencies. Placed at the center of the inverter board, the DSC samples phase currents via the ADC, runs the Park/Clarke transforms and PI current loops, and updates the PWM duty cycles every PWM period - tasks that would saturate a small MCU but fit comfortably in the DSPIC30F6010T-30I/PF's headroom. Compared with pure DSPs it also retains deterministic interrupt latency for the control loop, and the 80-pin TQFP package exposes enough pins for three-phase feedback, encoder, CAN and UART diagnostics.
Empfohlen
Digital Uninterruptible Power Supply (UPS) / PFC
The DSPIC30F6010T-30I/PF is widely used in single-phase and three-phase UPS inverter stages, active Power Factor Correction (PFC) and digital switch-mode power supplies where both tight voltage-mode control loops and DSP-class math are required on the same IC. Its 30 MIPS throughput comfortably runs average-current-mode PFC at 50-100 kHz switching frequencies, plus the inverter control loop that drives the output sine-wave PWM. The integrated 12-bit ADC samples the boost inductor current and AC line voltage at sufficient bandwidth for harmonic compensation, while the dedicated PWM module with programmable dead-time protects the half-bridge switches from shoot-through. Designers pair it with gate drivers and a current-sense amplifier to build a complete PFC + inverter stage, with CAN or UART used for status monitoring.
Empfohlen
Industrial Sensor Signal Conditioning / DSP Front-End
The DSPIC30F6010T-30I/PF serves as a digital signal processing front-end for industrial sensor systems such as vibration analyzers, flow meters and weigh scales that require on-board FIR/IIR filtering, FFT spectrum analysis and PID control. Its dual 40-bit accumulators and single-cycle MAC engine let the device run 16-bit FIR filters and Goertzel/FFT analysis at high sample rates without saturating the CPU, while the rich ADC and PWM peripherals close the analog loop. Combined with CAN/UART connectivity for plant-wide networking, this makes it a single-chip alternative to discrete MCU + external DSP solutions in size-constrained industrial sensor modules. The 144 KB Flash holds both the control firmware and DSP coefficient tables, and the 80-pin TQFP exposes the GPIO count required for sensor multiplexing and HMI interfacing.
Empfohlen
Audio Processing / Codec Interface
The DSPIC30F6010T-30I/PF's DCI (Data Converter Interface) peripheral and DSP throughput make it a viable host controller for audio codec applications, including speech processing, active noise cancellation front-ends and consumer audio effects boxes. The DCI peripheral streams audio samples directly to/from external ADC/DAC codecs, while the DSC's MAC engine runs biquad filters, dynamic range compression and limiter algorithms at full audio bandwidth. The SPI/I2C peripherals allow configuration of the codec chip, and the 144 KB Flash is sufficient for moderate FIR filter banks plus the main control code. Industrial temperature rating and on-chip EEPROM for user-preset storage round out its suitability for prosumer audio gear.
Empfohlen
Automotive Sensor and Actuator Control
For under-hood and chassis-area automotive subsystems such as electronic power steering, electric water pumps, HVAC blowers and transmission solenoids, the DSPIC30F6010T-30I/PF (industrial temperature) and its 'A' successor are used to run closed-loop control with CAN diagnostics. The 6-channel PWM, quadrature encoder interface and 12-bit ADC together cover the typical sensor set (position, current, temperature) and actuator drive (H-bridge or 3-phase inverter), while the integrated CAN peripheral enables OBD-II / CAN-FD diagnostics interfacing. Designers moving to AEC-Q100 qualified designs select the DSPIC30F6010AT-30I/PF variant, which shares the same 80-pin TQFP footprint and pinout for drop-in migration. The 144 KB Flash holds AUTOSAR-style application code plus calibration tables.
Empfohlen
Consumer Appliance Inverter Board
The DSPIC30F6010T-30I/PF is a popular controller for variable-frequency compressor and washing-machine drum drives in white goods, where cost, BOM integration and the 80-pin TQFP package's small footprint matter as much as raw MIPS. Its on-chip PWM, ADC and UART combine with a discrete IGBT gate driver and shunt-based current sense to form a complete single-chip inverter control solution, with the DSC handling sinusoidal startup, sensorless back-EMF commutation or FOC for premium models. The 144 KB Flash accommodates the appliance firmware plus the diagnostic and fault-logging routines, and the 4 KB EEPROM stores user settings (spin cycle, temperature) that survive power-off. Compared with a discrete MCU + external DSP, the integrated solution reduces BOM cost, PCB area and EMI vulnerability.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für DSPIC30F6010T-30I/PF – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | DSPIC30F6010A-30I/PF | DSPIC30F6010-30I/PF | DSPIC30F6010AT-30I/PF | DSPIC30F6010T-20I/PF | DSPIC30F6010T-20E/PF |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (PF, 14x14 mm) | 80-pin TQFP (PF, 14x14 mm) - same | 80-pin TQFP (PF, 14x14 mm) - same | 80-pin TQFP (PF, 14x14 mm) - same | 80-pin TQFP (PF, 14x14 mm) - same | 80-pin TQFP (PF, 14x14 mm) - same |
| Core | dsPIC30F 16-bit DSC | dsPIC30F 16-bit DSC | dsPIC30F 16-bit DSC | dsPIC30F 16-bit DSC | dsPIC30F 16-bit DSC | dsPIC30F 16-bit DSC |
| Max CPU Speed | 30 MIPS | 30 MIPS | 30 MIPS | 30 MIPS | 20 MIPS (-33%) | 20 MIPS (-33%) |
| Flash Memory | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB | 144 KB |
| RAM / EEPROM | 8 KB / 4 KB | 8 KB / 4 KB | 8 KB / 4 KB | 8 KB / 4 KB | 8 KB / 4 KB | 8 KB / 4 KB |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Automotive AEC-Q100) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) |
| Automotive Grade (AEC-Q100) | No | No | No | Yes (AEC-Q100) | No | No |
| Shipping Medium | Tape & Reel | Tray | Tray | Tape & Reel | Tape & Reel | Tape & Reel |
Wichtigste Unterscheidungsmerkmale
- Highest CPU speed grade in the dsPIC30F6010 family (vs. DSPIC30F6010T-20I/PF)
- Silicon revision A with errata fixes (vs. DSPIC30F6010A-30I/PF)
- Industrial temperature grade with Tape & Reel shipping (vs. DSPIC30F6010-30I/PF)
Designhinweise
The DSPIC30F6010T-30I/PF requires a single 2.5-5.5 V VDD rail, but its internal analog and digital subsystems benefit from separate AVDD/AVSS rails that should be tied to the same supply through an LC or ferrite-bead filter to keep digital switching noise out of the ADC reference. Place a 10 uF bulk capacitor plus a 100 nF ceramic decoupling cap as close as practical to every VDD/AVDD pin pair, and a 10 uF + 100 nF combination near the VREF+/VREF- pins. Estimated: with 80-pin TQFP and 6 PWM channels switching at 20 kHz, total decoupling capacitance above 22 uF is recommended to keep ripple below 50 mVpp on the analog rail.
The 80-pin TQFP (PF, 14x14 mm) package has a Theta-JA of approximately 50 C/W (still-air, JEDEC 4-layer board) and is rated for industrial -40 C to +85 C operation. At full 30 MIPS CPU load plus active ADC and PWM, the internal dissipation is well under 0.5 W so no heatsink is required, but the layout must provide at least 1 square inch of unbroken ground plane copper under the part to keep the die below Tj_max. Estimated: at 5 V VDD and 30 MIPS, the typical core current is ~80 mA, giving Pdiss around 400 mW and a 20 C junction rise above ambient with proper copper. Avoid placing the part near high-power components such as IGBTs or rectifiers on inverter boards.
Layout the 80-pin TQFP (PF, 14x14 mm, 0.65 mm pitch) with a 4-layer PCB where the top signal layer is dedicated to short, direct connections from the DSC to adjacent gate drivers and analog stages; use a continuous ground plane on layer 2; route the high-current PWM outputs on layer 3 with wide traces; and place filter/decoupling caps on the bottom layer directly under the device. Place the crystal or external clock within 1 cm of the OSC1/OSC2 pins, surrounded by a ground guard ring, and route all analog inputs (ANx) as differential pairs to current-sense amplifiers, keeping them away from PWM switching nodes.
Common pitfalls when designing with the DSPIC30F6010T-30I/PF include: (1) running the part above 7.5 MHz MIPS at VDD below 4.5 V, which violates the datasheet guarantee; (2) leaving the MCLR pin floating - it must be pulled high through a 10 kohm resistor for normal operation; (3) forgetting that the PGED1/PGEC1 pins are also EMUD1/EMUC1 for ICD debugging and should be accessible on the PCB; (4) configuring PWM outputs without enabling the PWM fault input protection, leaving the inverter exposed to shoot-through on a fault; (5) using a non-1:1 resistor divider on VREF without a buffer, which degrades ADC linearity. Always consult Microchip errata DS80175 for the DSPIC30F6010 base silicon revision before committing to production firmware.
Compliance-Informationen
RoHS and REACH compliant per Microchip product page. Standard DSPIC30F6010T-30I/PF is not AEC-Q100 qualified; for automotive, select the DSPIC30F6010AT-30I/PF variant.
