ISL8491IBZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas
Teilenummer: ISL8491IBZ ✗ AbgekündigtISL8491IBZ Übersicht
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and printed-circuit-board interconnects. Within the product hierarchy, it is a transceiver within interface ICs and a communications interface device. RS-422 emphasizes point-to-point, full-duplex balanced links, while RS-485 supports multipoint buses and commonly uses a half-duplex arrangement. The ISL8491IBZ provides separate transmit and receive paths for full-duplex use.
Key features include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply despite the nominal 5 V description, one-unit-load RS-485 bus loading, and support for both RS-485 and RS-422 signal environments. Its enable control can place the interface into a controlled state when the host does not require active communication. The 14-pin SOIC format is also used by the related ISL8490 and ESD-protected ISL8491E devices.
The BiCMOS implementation combines bipolar and CMOS characteristics to support high data rates in a single 5 V transceiver. Full-duplex topology separates the differential transmitter outputs from the differential receiver inputs, allowing transmission and reception to operate simultaneously. The 5 Mbps capability makes the device suitable for moderately high-speed industrial links, while the single-unit-load bus characteristic helps control loading when multiple nodes share an RS-485 network.
Typical applications include industrial automation equipment, factory data buses, industrial sensor interfaces, building-control networks, test and measurement systems, and embedded communications equipment. The device can also support full-duplex RS-422 point-to-point links between controllers and remote peripherals. System-level protocol framing, bus termination, grounding, and protection must still be designed around the cable environment.
Designers should use the manufacturer's pin-description table when assigning signals and should provide the supply decoupling recommended by the ISL8485, ISL8490, and ISL8491 datasheet. Differential routing should use a controlled-impedance PCB stack-up, with closely matched trace lengths and uninterrupted ground references helping reject common-mode noise.
This product page consolidates the obsolete lifecycle status, RS-485/RS-422 operating characteristics, drop-in family options, package details, and practical interface-design guidance into a focused engineering reference for legacy and redesign evaluations.
Drop-in-Alternativen für ISL8491IBZ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ISL8491IBZ (gleiche Bauform und Footprint).
ISL8491EIBZ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ISL8490IBZ
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →ISL8490EIBZ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ISL8491IB
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →ISL8491IBZ Technische Daten
| Product Type | RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 transmitter / 1 receiver |
| Duplex Mode | Full duplex |
| Nominal Supply Voltage | 5 V |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 5 Mbps |
| Supported Standards | RS-485 and RS-422 |
| RS-485 Bus Loading | 1 unit load |
| Technology | BiCMOS |
| Enable Control | Yes |
| Gehäuse | 14-pin SOIC |
| Montageart | Surface mount |
| Betriebstemperaturbereich | -40 °C to +85 °C |
| Lebenszyklusstatus | Obsolete |
ISL8491IBZ 14-pin soic Pinbelegungsleitfaden
Pinbelegung für ISL8491IBZ (14-pin soic-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für ISL8491IBZ.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ISL8491IBZ ist geeignet für 6 Anwendungs: Industrial Automation Field Bus, Full-Duplex RS-422 Link, Factory Sensor Gateway, Building Control Network, Test and Measurement Equipment, Embedded Communications Equipment.
Industrial Automation Field Bus
The ISL8491IBZ fits legacy industrial automation equipment that communicates over a balanced RS-485 field bus at rates up to 5 Mbps. Its one-unit-load bus characteristic helps preserve bus loading margins when several nodes share the cable, while the 4.5 V to 5.5 V operating range accommodates conventional 5 V control electronics. The full-duplex arrangement uses separate transmitter and receiver paths, supporting systems that need simultaneous communication rather than a shared half-duplex bus. Designers should preserve the original termination and protection strategy because replacing this obsolete transceiver does not eliminate the need to control cable transients, ground offsets, and common-mode noise.
Empfohlen
Full-Duplex RS-422 Link
The ISL8491IBZ is appropriate for a point-to-point RS-422 connection requiring separate transmit and receive paths. Its full-duplex configuration avoids sharing one bus pair between transmission and reception, while operation up to 5 Mbps supports faster equipment links than legacy low-speed serial interfaces. The device operates from 4.5 V to 5.5 V, making it suitable for systems with a regulated 5 V rail. In implementation, differential impedance, matched trace geometry, connector pin assignment, and the RS-422 termination arrangement must be controlled together. The transceiver can modernize the host interface without requiring a complete change to an existing balanced-cable infrastructure.
Empfohlen
Factory Sensor Gateway
A factory sensor gateway can use the ISL8491IBZ to connect a controller to remote sensing equipment over balanced copper cabling. The transceiver's 5 Mbps capability provides ample link margin for common sensor and actuator protocols, while the one-unit-load RS-485 presentation is useful in multi-node installations. Because the device is obsolete, it is most appropriate for repairing or replicating an established controller design rather than introducing it into a new platform without availability review. Maintain consistent bus polarity, use the required termination, and route the differential pair away from switching nodes to preserve reliable operation across the factory environment.
Empfohlen
Building Control Network
The ISL8491IBZ can support legacy building-control equipment that uses a 5 V balanced serial network. Its full-duplex RS-485/RS-422 capability is useful when the controller must exchange commands and receive sensor status simultaneously, and the 5 Mbps maximum rate allows compatibility with faster supervisory communication. The obsolete lifecycle status makes board-level reuse preferable to new adoption. In a building installation, follow the original grounding and cable-separation practices, select appropriate transient protection, and verify that the transceiver's enable state behaves correctly during controller startup and shutdown.
Empfohlen
Test and Measurement Equipment
The ISL8491IBZ is suitable for legacy test and measurement equipment that exposes a balanced RS-485 or RS-422 service port. The 5 Mbps rate supports rapid command and response traffic, and separate full-duplex paths simplify communication between an instrument controller and an external fixture. A 5 V laboratory rail falls within the device's 4.5 V to 5.5 V operating range. Engineers should use controlled-impedance routing and defined connector pinouts to prevent reflections or unintended ground loops. Because the exact part is obsolete, repair inventories should be checked before the board is released for production, while new test systems should assess current interface ICs.
Empfohlen
Embedded Communications Equipment
The ISL8491IBZ can provide the physical layer for an embedded controller communicating with a remote peripheral over a balanced cable. Its full-duplex arrangement supports concurrent command and response traffic, and its 5 Mbps capability allows the physical layer to accommodate protocols below that limit. The interface presents one unit load on an RS-485 bus, helping system designers maintain control of the total node count and cable topology. A legacy equipment redesign can retain the established connector and PCB routing while replacing only the obsolete transceiver, subject to detailed pin and electrical comparison with the selected replacement.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ISL8491IBZ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ISL8491EIBZ | ISL8490IBZ | ISL8490EIBZ | ISL8491IB |
|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps | 5 Mbps |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex | Full duplex |
Wichtigste Unterscheidungsmerkmale
- Same-family full-duplex footprint with a documented ESD-protected option (vs. ISL8491EIBZ)
- One-unit-load RS-485 bus interface (vs. ISL8490IBZ)
- Single-unit-load presentation supports bus-capacity planning (vs. ISL8490EIBZ)
Designhinweise
Route each differential pair as a coupled pair over a continuous ground plane, with matched spacing and approximately matched lengths. Avoid introducing stubs, test-point discontinuities, or plane changes beneath the pair. The maximum 5 Mbps capability is an electrical limit rather than a guarantee of usable cable distance; termination, topology, media, and connector return loss must be evaluated for the installation.
Power the ISL8491IBZ from a regulated source within its 4.5 V to 5.5 V range. Place the supply-decoupling network at the transceiver's power pins and keep its return path close to the device. Follow the manufacturer family datasheet for capacitor selection and placement, because inadequate local decoupling can allow supply excursions to corrupt the differential interface even when the external 5 V rail appears stable.
Use the manufacturer's 14-pin SOIC pin-description table to assign every connection and preserve the original component orientation. Before substituting another family member, compare enable polarity, driver-enable state, receiver enable behavior, and the meaning of every no-connect or supply pin on the assembled board. A shared footprint does not by itself prove that two devices can safely be exchanged.
Do not confuse the nominal 5 V rating with a wider supply range: the family is specified for 4.5 V to 5.5 V. Also verify the number of unit loads, termination arrangement, and full-duplex wiring against the actual network. For legacy industrial installations, add appropriate cable-side surge and ESD protection rather than assuming that the transceiver's internal ESD feature covers external connector transients.
Compliance-Informationen
No explicit compliance declarations were established for the exact ISL8491IBZ ordering code. The related ISL8491E designation denotes an ESD-protected family member, but an exact compliance statement must be obtained for each selected MPN.