Renesas Electronics

ISL8491IBZ - 5V 5Mbps RS-485/RS-422 Transceiver | Renesas

MPN: ISL8491IBZ ✗ 停產
5 V Vdss RS-485 and RS-422 Rds(on) 14-pin SOIC Package
MOQ: 1 |

ISL8491IBZ 概覽

The Renesas Electronics ISL8491IBZ is a 5 V, full-duplex, 1-transceiver/1-receiver RS-485/RS-422 interface IC operating at data rates up to 5 Mbps in a 14-pin SOIC package. It uses BiCMOS circuitry, accepts a 4.5 V to 5.5 V supply, presents one unit load to an RS-485 bus, and includes an enable-controlled operating mode for interface management.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over cables and printed-circuit-board interconnects. Within the product hierarchy, it is a transceiver within interface ICs and a communications interface device. RS-422 emphasizes point-to-point, full-duplex balanced links, while RS-485 supports multipoint buses and commonly uses a half-duplex arrangement. The ISL8491IBZ provides separate transmit and receive paths for full-duplex use.

Key features include a 5 Mbps maximum data rate, operation from a 4.5 V to 5.5 V supply despite the nominal 5 V description, one-unit-load RS-485 bus loading, and support for both RS-485 and RS-422 signal environments. Its enable control can place the interface into a controlled state when the host does not require active communication. The 14-pin SOIC format is also used by the related ISL8490 and ESD-protected ISL8491E devices.

The BiCMOS implementation combines bipolar and CMOS characteristics to support high data rates in a single 5 V transceiver. Full-duplex topology separates the differential transmitter outputs from the differential receiver inputs, allowing transmission and reception to operate simultaneously. The 5 Mbps capability makes the device suitable for moderately high-speed industrial links, while the single-unit-load bus characteristic helps control loading when multiple nodes share an RS-485 network.

Typical applications include industrial automation equipment, factory data buses, industrial sensor interfaces, building-control networks, test and measurement systems, and embedded communications equipment. The device can also support full-duplex RS-422 point-to-point links between controllers and remote peripherals. System-level protocol framing, bus termination, grounding, and protection must still be designed around the cable environment.

Designers should use the manufacturer's pin-description table when assigning signals and should provide the supply decoupling recommended by the ISL8485, ISL8490, and ISL8491 datasheet. Differential routing should use a controlled-impedance PCB stack-up, with closely matched trace lengths and uninterrupted ground references helping reject common-mode noise.

This product page consolidates the obsolete lifecycle status, RS-485/RS-422 operating characteristics, drop-in family options, package details, and practical interface-design guidance into a focused engineering reference for legacy and redesign evaluations.

直接替換替代品,適用於 ISL8491IBZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: ISL8491IBZ (相同外形與佔位).

ISL8491EIBZ

✅ 直接替換
📦 14-pin SOIC
Adds ESD protection while retaining the 5 V, 5 Mbps full-duplex interface and 14-pin SOIC footprint

📋 參考替代品(不在目錄中)

ISL8490IBZ

✅ 直接替換
Renesas Electronics
📦 14-pin SOIC
RS-485/RS-422 full-duplex transceiver · 1 transmitter and 1 receiver · 4.5 V to 5.5 V · 5 V · 5 Mbps · Full duplex · RS-485 and RS-422 · 1 unit load

聯絡詢價

查看資料表 →

ISL8490EIBZ

✅ 直接替換
📦 14-pin SOIC
Combines the 5 V, 5 Mbps full-duplex family with ESD protection; enable and I/O behavior require verification

📋 參考替代品(不在目錄中)

ISL8491IB

✅ 直接替換 ⚠️ 規格未經驗證
Renesas Electronics
📦 14-pin SOIC
5 V · Full-duplex transceiver · RS-485 and RS-422 · 1 · 1 · CMOS · Low power · High speed or slew-rate limited

聯絡詢價

查看資料表 →

ISL8491IBZ 規格

Product Type RS-485/RS-422 transceiver
Transceiver Configuration 1 transmitter / 1 receiver
Duplex Mode Full duplex
Nominal Supply Voltage 5 V
Supply Voltage Range 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps
Supported Standards RS-485 and RS-422
RS-485 Bus Loading 1 unit load
Technology BiCMOS
Enable Control Yes
封裝 14-pin SOIC
安裝類型 Surface mount
工作溫度範圍 -40 °C to +85 °C
生命週期狀態 Obsolete

ISL8491IBZ 14-pin soic 腳位配置指南

ISL8491IBZ(14-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

ISL8491IBZ 的 14-pin soic 封裝腳位圖

無詳細腳位定義資料: ISL8491IBZ.

請參閱 資料表 以查看完整腳位配置。

典型應用

ISL8491IBZ 適用於 6 應用s: Industrial Automation Field Bus, Full-Duplex RS-422 Link, Factory Sensor Gateway, Building Control Network, Test and Measurement Equipment, Embedded Communications Equipment.

🏭

Industrial Automation Field Bus

The ISL8491IBZ fits legacy industrial automation equipment that communicates over a balanced RS-485 field bus at rates up to 5 Mbps. Its one-unit-load bus characteristic helps preserve bus loading margins when several nodes share the cable, while the 4.5 V to 5.5 V operating range accommodates conventional 5 V control electronics. The full-duplex arrangement uses separate transmitter and receiver paths, supporting systems that need simultaneous communication rather than a shared half-duplex bus. Designers should preserve the original termination and protection strategy because replacing this obsolete transceiver does not eliminate the need to control cable transients, ground offsets, and common-mode noise.

🌐

Full-Duplex RS-422 Link

The ISL8491IBZ is appropriate for a point-to-point RS-422 connection requiring separate transmit and receive paths. Its full-duplex configuration avoids sharing one bus pair between transmission and reception, while operation up to 5 Mbps supports faster equipment links than legacy low-speed serial interfaces. The device operates from 4.5 V to 5.5 V, making it suitable for systems with a regulated 5 V rail. In implementation, differential impedance, matched trace geometry, connector pin assignment, and the RS-422 termination arrangement must be controlled together. The transceiver can modernize the host interface without requiring a complete change to an existing balanced-cable infrastructure.

🧩

Factory Sensor Gateway

A factory sensor gateway can use the ISL8491IBZ to connect a controller to remote sensing equipment over balanced copper cabling. The transceiver's 5 Mbps capability provides ample link margin for common sensor and actuator protocols, while the one-unit-load RS-485 presentation is useful in multi-node installations. Because the device is obsolete, it is most appropriate for repairing or replicating an established controller design rather than introducing it into a new platform without availability review. Maintain consistent bus polarity, use the required termination, and route the differential pair away from switching nodes to preserve reliable operation across the factory environment.

🏭

Building Control Network

The ISL8491IBZ can support legacy building-control equipment that uses a 5 V balanced serial network. Its full-duplex RS-485/RS-422 capability is useful when the controller must exchange commands and receive sensor status simultaneously, and the 5 Mbps maximum rate allows compatibility with faster supervisory communication. The obsolete lifecycle status makes board-level reuse preferable to new adoption. In a building installation, follow the original grounding and cable-separation practices, select appropriate transient protection, and verify that the transceiver's enable state behaves correctly during controller startup and shutdown.

🔧

Test and Measurement Equipment

The ISL8491IBZ is suitable for legacy test and measurement equipment that exposes a balanced RS-485 or RS-422 service port. The 5 Mbps rate supports rapid command and response traffic, and separate full-duplex paths simplify communication between an instrument controller and an external fixture. A 5 V laboratory rail falls within the device's 4.5 V to 5.5 V operating range. Engineers should use controlled-impedance routing and defined connector pinouts to prevent reflections or unintended ground loops. Because the exact part is obsolete, repair inventories should be checked before the board is released for production, while new test systems should assess current interface ICs.

📱

Embedded Communications Equipment

The ISL8491IBZ can provide the physical layer for an embedded controller communicating with a remote peripheral over a balanced cable. Its full-duplex arrangement supports concurrent command and response traffic, and its 5 Mbps capability allows the physical layer to accommodate protocols below that limit. The interface presents one unit load on an RS-485 bus, helping system designers maintain control of the total node count and cable topology. A legacy equipment redesign can retain the established connector and PCB routing while replacing only the obsolete transceiver, subject to detailed pin and electrical comparison with the selected replacement.

What is the ISL8491IBZ?
The ISL8491IBZ is a Renesas Electronics 5 V, full-duplex RS-485/RS-422 transceiver with separate transmit and receive paths and operation up to 5 Mbps. According to the Renesas ISL8485, ISL8490, and ISL8491 datasheet, it is a BiCMOS single-transceiver device housed in a 14-pin SOIC package. Its one-unit-load RS-485 interface and 4.5 V to 5.5 V operating range suit legacy industrial and point-to-point communications designs.
Is the ISL8491IBZ still active?
No, Renesas Electronics labels the ISL8491IBZ as obsolete on its official product page. Obsolete status means the part is no longer presented as a current lifecycle product, so production continuity should be confirmed through the Request a Quote form on this page. Legacy equipment may still be serviced with this device, but new designs should also evaluate current-interface alternatives and verify long-term availability before committing a BOM.
What is the supply voltage range of ISL8491IBZ?
The ISL8491IBZ operates from 4.5 V to 5.5 V, corresponding to the family tolerance around a nominal 5 V rail. According to the Renesas ISL8485, ISL8490, and ISL8491 datasheet, this range is a defining feature of the BiCMOS transceiver family. The board should provide a regulated 5 V source and follow the datasheet's decoupling recommendations to prevent supply disturbance from appearing as communication noise.
What data rate does ISL8491IBZ support?
The ISL8491IBZ supports data rates up to 5 Mbps. The Renesas product page and family datasheet both identify 5 Mbps as the family's maximum rate. This capability suits high-speed industrial links and full-duplex RS-422 connections, although cable length, baud rate, termination, grounding, and transceiver timing still determine whether a particular link can operate reliably at the theoretical maximum.
Where can I download the ISL8491IBZ datasheet PDF?
The ISL8491IBZ datasheet is available through Renesas Electronics at the official ISL8485, ISL8490, and ISL8491 datasheet page. The document contains the common specifications for the RS-485/RS-422 transceiver family and should be consulted for pin assignments, electrical characteristics, and application guidance. Use the manufacturer PDF rather than relying on a distributor summary when making footprint or timing decisions.
Where can I find the ISL8491IBZ pinout?
The ISL8491IBZ pin assignments are listed in the Renesas family datasheet and correspond to the 14-pin SOIC layout. The component is a full-duplex device with separate differential transmit and receive signals, power, ground, and enable-related connections. Assign every physical pin from the manufacturer's pin-description table and verify board routing against the selected package drawing before fabrication.
ISL8491IBZ vs ISL8490IBZ - which is better for a full-duplex link?
The ISL8491IBZ and ISL8490IBZ both belong to Renesas's 5 V, full-duplex RS-485/RS-422 family and support rates up to 5 Mbps in 14-pin SOIC packages. Their functional and control details must be checked in the family datasheet before substitution, particularly enable behavior and device-specific pin descriptions. The ISL8491IBZ is preferable when its exact enable and I/O characteristics match the original design exactly.
What is the difference between ISL8491IBZ and ISL8491EIBZ?
The primary functional distinction is ESD protection: the ISL8491EIBZ belongs to the ESD-protected family, while the ISL8491IBZ is the non-E designation. Both are presented as 5 V full-duplex RS-485/RS-422 transceivers in 14-pin SOIC packages with operation up to 5 Mbps. The ISL8491EIBZ is therefore the preferred candidate when additional electrostatic protection is required, subject to final pin and electrical verification.
What is the best drop-in replacement for ISL8491IBZ?
The closest same-footprint candidates are the Renesas ISL8491EIBZ, ISL8490IBZ, ISL8490EIBZ, and ISL8491IB ordering variants, each of which uses the 14-pin SOIC format. No fully documented cross-brand drop-in set was established from the available cross-reference results. Before selecting any candidate, compare enable polarity, receiver output behavior, bus loading, ESD rating, and every datasheet pin description.
Can ISL8491EIBZ replace ISL8491IBZ?
The ISL8491EIBZ can be considered a candidate because it uses the same 14-pin SOIC package and belongs to the same 5 V, 5 Mbps full-duplex RS-485/RS-422 family. Its distinguishing feature is ESD protection. Confirm that the enable input and transceiver signal pins are electrically equivalent and that the added protection does not alter the board's intended behavior before treating it as a production drop-in replacement.
When should I choose ISL8491IBZ over a newer transceiver?
Choose the ISL8491IBZ for maintenance of an existing 14-pin SOIC board when its established pin behavior, 5 V supply operation, and maximum 5 Mbps data rate match the original design. It is not the best choice for a new design without a lifecycle review because Renesas marks it obsolete. For new products, compare current transceivers by supply range, ESD rating, fail-safe behavior, connector protection, and bus-node count.
Is ISL8491IBZ suitable for RS-422 and RS-485 interfaces?
Yes, the ISL8491IBZ is specified for both RS-422 and RS-485 balanced communication. Its full-duplex configuration provides separate transmit and receive paths, making it directly suitable for point-to-point RS-422 links and for full-duplex arrangements of RS-485. Bus implementation still requires correct termination, common-mode grounding, cable routing, and protection appropriate to the installation environment.
What are the key specifications of ISL8491IBZ that engineers should know?
The key ISL8491IBZ specifications are a 4.5 V to 5.5 V supply range, operation up to 5 Mbps, full-duplex RS-485/RS-422 operation, one-unit-load bus loading, and a 14-pin SOIC package. According to the Renesas family datasheet, the device uses BiCMOS circuitry and includes an enable function. These characteristics define its suitability for legacy 5 V balanced-interface systems.
What can replace an obsolete ISL8491IBZ transceiver?
A replacement should first be selected from the same Renesas 14-pin SOIC family, with the ISL8491EIBZ, ISL8490IBZ, ISL8490EIBZ, and ISL8491IB ordering variants serving as documented candidates. Cross-brand substitution requires a separate engineering review of pinout, enable polarity, receiver behavior, ESD protection, supply range, and bus loading. The Request a Quote form on this page can be used to confirm availability and sourcing options.
Where can I buy ISL8491IBZ and what is its price and lead time?
Use the Request a Quote form on this page to request the ISL8491IBZ price, stock status, and current production lead time. The Renesas product page identifies the device as obsolete, so availability may depend on remaining inventory rather than an active manufacturing schedule. Submit the exact ISL8491IBZ ordering code and required quantity to obtain a current sourcing response.

工程參考資料,適用於 ISL8491IBZ — 比較、設計指引及合規資訊。

選型指南

Choose the ISL8491IBZ when repairing or cloning an established 14-pin SOIC board that uses a 5 V full-duplex RS-485/RS-422 interface and operates at or below 5 Mbps. Prefer ISL8491EIBZ when the original board benefits from an ESD-protected family member and its enable and I/O behavior pass a complete pin-level comparison. Use ISL8490IBZ or ISL8490EIBZ only after verifying the family-specific control differences against the circuit and required bus topology. ISL8491IB is a legacy ordering candidate worth reviewing when exact procurement equivalence matters. Because the target is obsolete, request current inventory and lead-time confirmation before committing to production. For a genuinely new design, evaluate current transceivers with fail-safe receiver behavior, wider supply tolerance, higher ESD ratings, and a suitable bus-node count instead of treating legacy continuity as the primary requirement.

與替代品比較

參數 本產品 ISL8491EIBZ ISL8490IBZ ISL8490EIBZ ISL8491IB
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Nominal Supply Voltage 5 V 5 V 5 V 5 V 5 V
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps 5 Mbps 5 Mbps 5 Mbps 5 Mbps
Duplex Mode Full duplex Full duplex Full duplex Full duplex Full duplex

主要差異化特點

  • Same-family full-duplex footprint with a documented ESD-protected option (對比ISL8491EIBZ)
  • One-unit-load RS-485 bus interface (對比ISL8490IBZ)
  • Single-unit-load presentation supports bus-capacity planning (對比ISL8490EIBZ)

設計說明

Route each differential pair as a coupled pair over a continuous ground plane, with matched spacing and approximately matched lengths. Avoid introducing stubs, test-point discontinuities, or plane changes beneath the pair. The maximum 5 Mbps capability is an electrical limit rather than a guarantee of usable cable distance; termination, topology, media, and connector return loss must be evaluated for the installation.

Power the ISL8491IBZ from a regulated source within its 4.5 V to 5.5 V range. Place the supply-decoupling network at the transceiver's power pins and keep its return path close to the device. Follow the manufacturer family datasheet for capacitor selection and placement, because inadequate local decoupling can allow supply excursions to corrupt the differential interface even when the external 5 V rail appears stable.

Use the manufacturer's 14-pin SOIC pin-description table to assign every connection and preserve the original component orientation. Before substituting another family member, compare enable polarity, driver-enable state, receiver enable behavior, and the meaning of every no-connect or supply pin on the assembled board. A shared footprint does not by itself prove that two devices can safely be exchanged.

Do not confuse the nominal 5 V rating with a wider supply range: the family is specified for 4.5 V to 5.5 V. Also verify the number of unit loads, termination arrangement, and full-duplex wiring against the actual network. For legacy industrial installations, add appropriate cable-side surge and ESD protection rather than assuming that the transceiver's internal ESD feature covers external connector transients.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

No explicit compliance declarations were established for the exact ISL8491IBZ ordering code. The related ISL8491E designation denotes an ESD-protected family member, but an exact compliance statement must be obtained for each selected MPN.

相關搜尋

ISL8491IBZ datasheet ISL8491IBZ pinout ISL8491IBZ datasheet pdf ISL8491IBZ equivalent ISL8491IBZ replacement ISL8491IBZ cross reference Renesas ISL8491IBZ ISL8491IBZ 5Mbps transceiver ISL8491IBZ 14 SOIC ISL8491IBZ RS-485 application ISL8491IBZ vs ISL8491EIBZ ISL8491IBZ price

相關元件與詞彙

Renesas Electronics ISL8491IBZ ISL8491EIBZ ISL8490IBZ ISL8490EIBZ ISL8491IB RS-485 RS-422 BiCMOS full-duplex transceiver interface IC balanced differential signal transceiver semiconductor 14-pin SOIC SOIC package family surface-mount package industrial automation factory field bus building control network test and measurement equipment 5 Mbps data rate one unit load enable control
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情