LC4032ZC-5M56I - 400MHz 32-Macro-Cell CPLD | Lattice
Teilenummer: LC4032ZC-5M56I ✓ AktivLC4032ZC-5M56I Übersicht
A complex programmable logic device, or CPLD, is a programmable semiconductor in the FPGA and CPLD family. Unlike a mask-programmed logic device, a CPLD retains its programmed configuration in nonvolatile memory and can be reprogrammed during production, field updates, or in-system operation. Its architecture combines configurable logic blocks, programmable interconnect, input/output blocks, and global clock resources. This places it between simple fixed-logic devices and higher-capacity FPGAs in the broader programmable-logic hierarchy.
Key features include 32 macro cells, 32 user I/Os, a 400 MHz maximum operating frequency, and a 2.5 ns stated propagation delay. The listed 192 MHz internal frequency provides a separate performance reference for the device architecture. Operation from 1.8 V through 3.3 V gives designers flexibility across low-voltage system rails, while four global clock pins support distributed clocking and multi-domain control logic. In-system programmability also allows configuration updates without removing the device from its operating environment.
The combination of 32 macro cells and 32 user I/Os enables moderately complex control paths, bus arbitration, protocol bridging, state-machine implementation, and peripheral-interface logic. The 400 MHz headline frequency is relevant for timing-critical synchronous designs, although real system performance also depends on the selected architecture, external memory interface, input/output standards, clocking topology, and timing constraints used during implementation. The 2.5 ns propagation-delay figure should therefore be treated as a device-level reference rather than a guarantee for every routed path.
Typical applications include industrial control and factory automation, communications-interface logic, instrumentation, consumer equipment, embedded control, and general-purpose prototype or production-programming boards. The device is especially useful when a design requires nonvolatile configuration, modest logic density, numerous user I/Os, and rapid implementation changes without moving to a larger programmable-logic device.
PCB design should preserve the manufacturer's recommended power, ground, clock, and programmable-interface layout. Decoupling capacitors must be placed close to the appropriate supply pins, clock routes should remain short and controlled, and unused inputs should be assigned explicitly in the design tool. Programming-system compatibility, pin constraints, and the exact CABGA land pattern must be checked before the footprint is released for fabrication.
This product record combines the exact LC4032ZC-5M56I configuration, package and timing characteristics, sourced replacement information, application guidance, and design-focused selection criteria. It supports engineers comparing programmable-logic capacity, voltage options, clock resources, and board-level replacement decisions before beginning schematic capture.
Drop-in-Alternativen für LC4032ZC-5M56I – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LC4032ZC-5M56I (gleiche Bauform und Footprint) – abweichend in Global Clock Pins, Product Type.
LC4032ZC-5MN56I
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LC4032ZC-5M56I Grenzwerte & elektrische Eigenschaften
| Product Type | Complex programmable logic device |
| Architecture | SuperFast high-density PLD |
| Logic Family | CMOS |
| Macro Cells | 32 macro cells |
| Maximum Operating Frequency | 400 MHz |
| Internal Frequency | 192 MHz |
| Propagation Delay | 2.5 ns |
| Listed Prop Delay | 4.4 ns |
| User I/Os | 32 pins |
| Total Package Pins | 49 pins |
| Package Type | CABGA-49 |
| Versorgungsspannung | 1.8 V |
| Supported Supply Voltages | 1.8 V, 2.5 V, and 3.3 V |
| Global Clock Pins | Up to 4 pins |
| Programmability | In-system programmable |
| Mounting Technology | Surface mount |
LC4032ZC-5M56I cabga-49 Pinbelegungsleitfaden
Pinbelegung für LC4032ZC-5M56I (cabga-49-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für LC4032ZC-5M56I.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LC4032ZC-5M56I ist geeignet für 6 Anwendungs: Industrial Control Logic, Communications Interface Bridging, Instrumentation Signal Conditioning, Programmable Sensor Hub, Consumer and Communication Equipment, Embedded System Support Logic.
Industrial Control Logic
The LC4032ZC-5M56I fits compact machine-control logic where a fixed standard IC cannot accommodate product-specific sequencing. Its 32 macro cells and 32 user I/Os can implement state machines, interlocks, input conditioning, actuator-command logic, and diagnostic routines. The 400 MHz maximum operating frequency and 2.5 ns listed propagation delay provide ample timing headroom for many control paths. Its three supported supply levels—1.8 V, 2.5 V, and 3.3 V—also help align core logic, communications, and external interface sections within one programmable device. Engineers should still verify the exact temperature rating and use the manufacturer pin table when assigning control signals.
Empfohlen
Communications Interface Bridging
The LC4032ZC-5M56I is appropriate for protocol conversion, framing, buffering, and interface arbitration between embedded systems. Thirty-two user I/Os provide connectivity for parallel data, control signals, and clock-domain crossing, while four global clock pins support distributed timing across independent functional blocks. The in-system-programmable architecture allows interface revisions to be handled through configuration changes rather than a new fixed-logic part. Its 32 macro cells are best suited to moderate protocol logic rather than high-bandwidth serial engines. Final timing closure should use the Lattice Semiconductor implementation tools and verify I/O voltage compatibility with every connected external device.
Empfohlen
Instrumentation Signal Conditioning
The LC4032ZC-5M56I can implement acquisition sequencing, measurement timing, trigger handling, and sensor-interface control in compact instrumentation. Its 32 user I/Os support parallel sensor buses and control signals, while programmable global clocks help coordinate sampling and conversion events. The 400 MHz maximum operating frequency accommodates timing blocks that must respond deterministically to external events. Because measurement accuracy often depends on analog isolation, grounding, and reference design rather than digital speed alone, this CPLD should be placed as the timing and control element rather than as an analog front end. Confirm input thresholds, supply sequencing, and package-specific decoupling before layout release.
Empfohlen
Programmable Sensor Hub
The LC4032ZC-5M56I suits a compact sensor hub that combines multiple digital sensors with host-side control logic. Thirty-two macro cells can support sensor configuration, interrupt arbitration, calibration sequences, timestamp handling, and communication framing, while 32 user I/Os permit direct attachment to several sensors and a host interface. The three listed supply voltages offer flexibility when the hub includes mixed-voltage peripherals, although each I/O bank limit must still be respected. In-system programmability simplifies product variants and field updates by retaining configuration in nonvolatile memory. Board-level planning should include defined programming access, pull resistors where required, and careful routing of clock and sensor signals.
Empfohlen
Consumer and Communication Equipment
The LC4032ZC-5M56I can consolidate product-specific control functions in communication or consumer equipment where board space is constrained. Its CABGA-49 package, 32 user I/Os, four global clock pins, and 32 macro cells provide a dense implementation target for status logic, key scanning, display sequencing, peripheral selection, and data-path adapters. The 400 MHz maximum operating frequency is suitable for synchronous control and moderate-width interfaces. Its in-system programmability also helps manage feature revisions, regional configuration differences, and production test requirements. Designers should use the manufacturer package drawing for land-pattern geometry and verify whether the specific ordering code supports the required industrial temperature range and supply sequencing.
Empfohlen
Embedded System Support Logic
The LC4032ZC-5M56I is useful as reconfigurable support logic around a microprocessor, microcontroller, or FPGA. The 32 macro cells can implement boot sequencing, peripheral chip-select logic, watchdog handling, interrupt combination, bus arbitration, and specialized timing adapters. A 2.5 ns listed propagation delay and four global clock pins support fast control paths, while the 400 MHz maximum operating frequency provides margin for synchronous interface logic. The device is especially practical when the support logic is expected to evolve more quickly than the main processor board. Engineers should define unused-pin behavior, programming-chain connectivity, and reset states explicitly in the Lattice Semiconductor design implementation.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LC4032ZC-5M56I – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LC4032ZC-5MN56I |
|---|---|---|
| Package | CABGA-49 | CABGA-49 |
| Brand | Lattice Semiconductor | Lattice Semiconductor |
| Macro Cells | 32 macro cells | 32 macro cells |
| User I/Os | 32 pins | 32 pins |
| Maximum Operating Frequency | 400 MHz | 400 MHz |
| Internal Frequency | 192 MHz | 192 MHz |
| Propagation Delay | 2.5 ns | 2.5 ns |
| Listed Prop Delay | 4.4 ns | 4.4 ns |
| Supply Voltage | 1.8 V | 1.8 V |
| Supported Supply Voltages | 1.8 V, 2.5 V, and 3.3 V | 1.8 V, 2.5 V, and 3.3 V |
| Global Clock Pins | Up to 4 pins | Up to 4 pins |
| Programmability | In-system programmable | In-system programmable |
Wichtigste Unterscheidungsmerkmale
- Exact 32-macro-cell configuration with 32 user I/Os (vs. LC4032ZC-5MN56I)
- Full 400 MHz maximum operating-frequency match (vs. LC4032ZC-5MN56I)
- Matching core timing characteristics (vs. LC4032ZC-5MN56I)
- Three listed supply-voltage options (vs. LC4032ZC-5MN56I)
Designhinweise
Use the manufacturer CABGA-49 package drawing and pin table to construct the PCB footprint, including ball assignments, pad dimensions, solder-mask definition, and paste apertures. Place supply decoupling capacitors adjacent to their associated power balls, provide a low-impedance ground return, and avoid routing configuration signals through areas with switching or high-current outputs. Because the device is only 49 pins and uses a dense CABGA package, assembly capability and inspection requirements should be confirmed before fabrication.
Route clocks as short, continuous paths with controlled return references and avoid stubs, test pads, and unnecessary layer transitions. The device supports up to four global clock pins and a maximum operating frequency of 400 MHz, so clock distribution and source synchronization require disciplined PCB layout. Match external interface timing to the selected I/O standard and include series damping where source-edge ringing or destination overshoot is observed. Final timing constraints should be implemented and checked in the Lattice Semiconductor design tool.
Do not infer that every LC4032ZC suffix has identical temperature, qualification, or device-revision characteristics. Before replacing LC4032ZC-5M56I with LC4032ZC-5MN56I, compare the complete suffix in the manufacturer documentation, confirm configuration-file compatibility, and review the programming interface requirements. Also assign every unused input explicitly, maintain the required power-up and programming conditions, and verify that external I/O voltages do not exceed the selected I/O bank's limits.
Plan the 1.8 V, 2.5 V, or 3.3 V rail according to the device configuration and board architecture, then verify startup sequencing for all connected devices. Place stable decoupling at the supply and ground balls and keep supply traces short to reduce impedance. Configuration pins must not be left without defined levels when required by the design. Power-supply capacity should include normal operating consumption plus the transient demand of logic transitions and any attached peripherals.
Compliance-Informationen
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for this exact ordering code.