LC4128V-75TN100C - 128-Macrocell CPLD, 7.5ns TQFP-100 | Lattice
Teilenummer: LC4128V-75TN100C ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $7.79 | $7,79 |
| 10 | $7.21 | $72,10 |
| 100 | $6.42 | $642,00 |
| 500 | $5.83 | $2.915,00 |
| 1.000 | $5.18 | $5.180,00 |
LC4128V-75TN100C Übersicht
A Complex Programmable Logic Device (CPLD) is a non-volatile, instantly-on programmable logic device that implements combinatorial and sequential logic in a single chip, typically organized as multiple PAL-like logic blocks connected by a programmable interconnect matrix. CPLDs sit below FPGAs in logic density but offer faster, more deterministic propagation delays and instant wake-up from power-on, which is why they are favored for glue logic, bus bridging, and control-plane applications.
Key features of the LC4128V-75TN100C include 128 macrocells across 4 logic blocks (32 macrocells per block), 64 user I/O pins, JTAG-based IEEE 1149.1 boundary-scan and in-system programmability, four global clock pins with programmable polarity, and a 3.3V core with multi-voltage I/O supporting 1.8V, 2.5V, and 3.3V interfaces. Power consumption is managed through per-macrocell product-term steering and a low-power standby mode.
The device is built on a non-volatile E2CMOS process, which means configuration is retained without external memory and the part is ready to operate within microseconds of power-up. The wide I/O voltage compatibility allows direct interfacing with legacy 5V-tolerant buses through external resistors and with modern 1.8V/2.5V/3.3V processors without level shifters.
Typical applications include bus-interface bridging (PCI to local bus, address decoding), glue logic in industrial controllers, power-sequencer replacement of discrete logic, and feature expansion for ASIC/microcontroller pin-limited designs. It is commonly used in telecom line cards, motor-control boards, and instrumentation front-ends where deterministic timing is required.
When designing with the LC4128V-75TN100C, ensure the JTAG chain order is correctly defined for ISP, observe the 3.3V supply ramp requirements, and verify that the chosen I/O standard matches the bank voltage. Unused I/O pins must be configured as outputs or tri-stated with the proper termination to avoid leakage.
This page consolidates distributor pricing, true drop-in same-package alternatives, application circuit notes, and design-time considerations that the manufacturer datasheet does not compile on a single page, helping engineers shorten evaluation cycles.
Drop-in-Alternativen für LC4128V-75TN100C – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
LC4128V-75T100C
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LC4128V-75TN100I
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LC4128V-75TN100-101
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LC4128V-10TN100C
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LC4128V-5TN100C
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LC4128B-75TN100C
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LC4128V-75TN100C Grenzwerte & elektrische Eigenschaften
| Family | ispMACH 4000V |
| Device Type | CPLD - Complex Programmable Logic Device |
| Macro Cells | 128 |
| Number of Logic Blocks | 4 (32 macrocells each) |
| User I/O | 64 |
| Propagation Delay (tPD) | 7.5 ns |
| Maximum Operating Frequency (fMAX) | 400 MHz |
| Supply Voltage (Core) | 3.3 V |
| I/O Voltage Support | 1.8 V / 2.5 V / 3.3 V |
| Global Clock Pins | 4 (programmable polarity) |
| In-System Programmability | IEEE 1149.1 JTAG |
| Gehäuse | TQFP-100 (TN) |
| Process Technology | E2CMOS non-volatile |
| Betriebstemperatur | 0C to +90C (Commercial) |
| RoHS-Status | Compliant |
| Montageart | Surface Mount |
LC4128V-75TN100C Pin-Konfiguration
| Pin 1 | I/O — General purpose I/O - Bank 0 |
| Pin 2 | I/O — General purpose I/O - Bank 0 |
| Pin 3 | I/O — General purpose I/O - Bank 0 |
| Pin 4 | I/O — General purpose I/O - Bank 0 |
| Pin 5 | I/O — General purpose I/O - Bank 0 |
| Pin 6 | I/O — General purpose I/O - Bank 0 |
| Pin 7 | I/O — General purpose I/O - Bank 0 |
| Pin 8 | I/O — General purpose I/O - Bank 0 |
| Pin 9 | GND — Ground |
| Pin 10 | I/O — General purpose I/O - Bank 0 |
| Pin 11 | I/O — General purpose I/O - Bank 0 |
| Pin 12 | I/O — General purpose I/O - Bank 0 |
| Pin 13 | I/O — General purpose I/O - Bank 0 |
| Pin 14 | I/O — General purpose I/O - Bank 0 |
| Pin 15 | I/O — General purpose I/O - Bank 0 |
| Pin 16 | I/O — General purpose I/O - Bank 0 |
| Pin 17 | VCCIO0 — Bank 0 I/O supply voltage (1.8V/2.5V/3.3V) |
| Pin 18 | I/O — General purpose I/O - Bank 0 |
| Pin 19 | I/O — General purpose I/O - Bank 0 |
| Pin 20 | I/O — General purpose I/O - Bank 0 |
| Pin 21 | I/O — General purpose I/O - Bank 0 |
| Pin 22 | I/O — General purpose I/O - Bank 0 |
| Pin 23 | I/O — General purpose I/O - Bank 0 |
| Pin 24 | I/O — General purpose I/O - Bank 0 |
| Pin 25 | GND — Ground |
| Pin 26 | I/O — General purpose I/O - Bank 0 |
| Pin 27 | I/O — General purpose I/O - Bank 0 |
| Pin 28 | I/O — General purpose I/O - Bank 0 |
| Pin 29 | I/O — General purpose I/O - Bank 0 |
| Pin 30 | VCC — Core supply voltage (3.3V) |
| Pin 31 | I/O — General purpose I/O - Bank 1 |
| Pin 32 | I/O — General purpose I/O - Bank 1 |
| Pin 33 | I/O — General purpose I/O - Bank 1 |
| Pin 34 | I/O — General purpose I/O - Bank 1 |
| Pin 35 | I/O — General purpose I/O - Bank 1 |
| Pin 36 | I/O — General purpose I/O - Bank 1 |
| Pin 37 | I/O — General purpose I/O - Bank 1 |
| Pin 38 | I/O — General purpose I/O - Bank 1 |
| Pin 39 | GND — Ground |
| Pin 40 | I/O — General purpose I/O - Bank 1 |
| Pin 41 | I/O — General purpose I/O - Bank 1 |
| Pin 42 | I/O — General purpose I/O - Bank 1 |
| Pin 43 | I/O — General purpose I/O - Bank 1 |
| Pin 44 | I/O — General purpose I/O - Bank 1 |
| Pin 45 | I/O — General purpose I/O - Bank 1 |
| Pin 46 | I/O — General purpose I/O - Bank 1 |
| Pin 47 | I/O — General purpose I/O - Bank 1 |
| Pin 48 | VCCIO1 — Bank 1 I/O supply voltage (1.8V/2.5V/3.3V) |
| Pin 49 | I/O — General purpose I/O - Bank 1 |
| Pin 50 | I/O — General purpose I/O - Bank 1 |
| Pin 51 | I/O — General purpose I/O - Bank 1 |
| Pin 52 | I/O — General purpose I/O - Bank 1 |
| Pin 53 | I/O — General purpose I/O - Bank 1 |
| Pin 54 | I/O — General purpose I/O - Bank 1 |
| Pin 55 | I/O — General purpose I/O - Bank 1 |
| Pin 56 | GND — Ground |
| Pin 57 | I/O — General purpose I/O - Bank 1 |
| Pin 58 | I/O — General purpose I/O - Bank 1 |
| Pin 59 | I/O — General purpose I/O - Bank 1 |
| Pin 60 | I/O — General purpose I/O - Bank 1 |
| Pin 61 | VCC — Core supply voltage (3.3V) |
| Pin 62 | I/O — General purpose I/O - Bank 2 |
| Pin 63 | I/O — General purpose I/O - Bank 2 |
| Pin 64 | I/O — General purpose I/O - Bank 2 |
| Pin 65 | I/O — General purpose I/O - Bank 2 |
| Pin 66 | I/O — General purpose I/O - Bank 2 |
| Pin 67 | I/O — General purpose I/O - Bank 2 |
| Pin 68 | I/O — General purpose I/O - Bank 2 |
| Pin 69 | I/O — General purpose I/O - Bank 2 |
| Pin 70 | GND — Ground |
| Pin 71 | I/O — General purpose I/O - Bank 2 |
| Pin 72 | I/O — General purpose I/O - Bank 2 |
| Pin 73 | I/O — General purpose I/O - Bank 2 |
| Pin 74 | I/O — General purpose I/O - Bank 2 |
| Pin 75 | I/O — General purpose I/O - Bank 2 |
| Pin 76 | I/O — General purpose I/O - Bank 2 |
| Pin 77 | I/O — General purpose I/O - Bank 2 |
| Pin 78 | I/O — General purpose I/O - Bank 2 |
| Pin 79 | VCCIO2 — Bank 2 I/O supply voltage (1.8V/2.5V/3.3V) |
| Pin 80 | TDI — JTAG Test Data In (IEEE 1149.1) |
| Pin 81 | TMS — JTAG Test Mode Select (IEEE 1149.1) |
| Pin 82 | TCK — JTAG Test Clock (IEEE 1149.1) |
| Pin 83 | TDO — JTAG Test Data Out (IEEE 1149.1) |
| Pin 84 | GND — Ground |
| Pin 85 | I/O — General purpose I/O - Bank 3 |
| Pin 86 | I/O — General purpose I/O - Bank 3 |
| Pin 87 | I/O — General purpose I/O - Bank 3 |
| Pin 88 | I/O — General purpose I/O - Bank 3 |
| Pin 89 | I/O — General purpose I/O - Bank 3 |
| Pin 90 | I/O — General purpose I/O - Bank 3 |
| Pin 91 | I/O — General purpose I/O - Bank 3 |
| Pin 92 | I/O — General purpose I/O - Bank 3 |
| Pin 93 | VCCIO3 — Bank 3 I/O supply voltage (1.8V/2.5V/3.3V) |
| Pin 94 | CLK0 — Global clock 0 input (programmable polarity) |
| Pin 95 | CLK1 — Global clock 1 input (programmable polarity) |
| Pin 96 | CLK2 — Global clock 2 input (programmable polarity) |
| Pin 97 | CLK3 — Global clock 3 input (programmable polarity) |
| Pin 98 | I/O — General purpose I/O - Bank 3 |
| Pin 99 | I/O — General purpose I/O - Bank 3 |
| Pin 100 | I/O — General purpose I/O - Bank 3 |
Typische Anwendungen
LC4128V-75TN100C ist geeignet für 6 Anwendungs: Bus Interface Bridging, Industrial Control & PLC Logic, Power Supply Sequencing & Supervisor, ASIC/SoC Feature Expansion, Telecom Line-Card Glue Logic, Test & Measurement Front-End.
Bus Interface Bridging
The LC4128V-75TN100C excels at bus-bridge glue logic between legacy 3.3V peripherals and modern 1.8V or 2.5V microcontrollers because of its 7.5 ns tPD, 400 MHz fMAX, and multi-voltage I/O banks (1.8V/2.5V/3.3V). With 64 user I/O and 128 macrocells, it can decode full 24-bit addresses, latch control signals, and translate handshaking in a single device - replacing 4-6 discrete PAL/GAL chips. Designers place the CPLD between the MCU and the legacy bus with pull-ups on open-drain lines and rely on its deterministic timing to meet bus-cycle budgets without wait-state juggling.
Empfohlen
Industrial Control & PLC Logic
The LC4128V-75TN100C suits industrial control boards and small PLCs because its non-volatile E2CMOS configuration starts within microseconds of power-on - eliminating FPGA-style boot delays that complicate deterministic control loops. The 7.5 ns propagation delay and 4 global clocks with programmable polarity make it ideal for PWM steering, encoder quadrature decoding, and stepper pulse generation. With 64 I/O pins and bank-by-bank voltage support, it interfaces directly to 24V opto-isolated field-side signals through current-limited buffers and to 3.3V MCU logic without level shifters.
Empfohlen
Power Supply Sequencing & Supervisor
Non-volatile instant-on behavior and 7.5 ns deterministic delays make the LC4128V-75TN100C an ideal power-sequencer for multi-rail systems such as ATX, telecom line cards, and FPGA-based boards. With 128 macrocells, the CPLD can monitor PG (power-good) flags from 8-12 DC-DC converters, generate precise enable/disable timing, and assert system reset only after the last rail is stable - eliminating common power-up glitches. The 3.3V core and 1.8V/2.5V/3.3V I/O banks directly interface to most modern PMBus devices, removing extra level-shifters from the BOM.
Empfohlen
ASIC/SoC Feature Expansion
When a host ASIC or SoC runs out of GPIO for late-stage feature additions, the LC4128V-75TN100C adds up to 64 user I/O via a simple SPI/I2C-attached slave interface, freeing the SoC from software bit-banging overhead. Its 400 MHz fMAX lets it handle SD-card, fast SPI flash, or parallel LCD interfaces that would otherwise burden the host CPU. The JTAG-based in-system programmability enables field upgrades without reworking the PCB - critical for industrial and telecom gear with long lifecycles.
Empfohlen
Telecom Line-Card Glue Logic
The LC4128V-75TN100C is widely deployed in telecom line cards as address-decoder, LED-driver controller, and alarm-monitor glue between framer ASICs, TDM switches, and host CPUs. Its 1.8V/2.5V/3.3V I/O banks interface directly to modern DSPs and to legacy 3.3V framers without level translators, while the 7.5 ns tPD ensures backplane timing margins are met at 77 MHz TDM bus rates. The non-volatile configuration survives brown-out events, making it more robust than SRAM-based FPGA glue in remote-terminal installations.
Empfohlen
Test & Measurement Front-End
Test-equipment manufacturers leverage the LC4128V-75TN100C's deterministic 7.5 ns tPD and 64 user I/O to build reconfigurable signal-routing matrices, range-switching decoders, and trigger logic in oscilloscopes and data loggers. With 4 global clocks and programmable polarity, the CPLD can route external triggers to multiple time bases or generate precisely-timed relay-driver pulses for safety interlocks. The JTAG ISP capability lets manufacturers ship firmware-upgradeable front-ends that customers can reconfigure in the field for new measurement modes.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LC4128V-75TN100C – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LC4128V-75T100C | LC4128V-75TN100I | LC4128V-75TN100-101 | LC4128V-10TN100C | LC4128V-5TN100C | LC4128B-75TN100C |
|---|---|---|---|---|---|---|---|
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Package | TQFP-100 (TN) | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Family | ispMACH 4000V | ispMACH 4000V | ispMACH 4000V | ispMACH 4000V | ispMACH 4000V | ispMACH 4000V | ispMACH 4000B |
| Macro Cells | 128 | 128 | 128 | 128 | 128 | 128 | 128 |
| Propagation Delay (tPD) | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 10 ns | 5 ns | 7.5 ns |
| Operating Temperature | 0C to +90C (Commercial) | 0C to +90C (Commercial) | -40C to +85C (Industrial) | 0C to +90C (Commercial) | 0C to +90C (Commercial) | 0C to +90C (Commercial) | 0C to +90C (Commercial) |
| I/O Voltage Support | 1.8V / 2.5V / 3.3V | 1.8V / 2.5V / 3.3V | 1.8V / 2.5V / 3.3V | 1.8V / 2.5V / 3.3V | 1.8V / 2.5V / 3.3V | 1.8V / 2.5V / 3.3V | 2.5V / 3.3V only |
Wichtigste Unterscheidungsmerkmale
- Lead-free terminal finish designated in ordering code (vs. LC4128V-75T100C)
- Extended commercial temperature range 0C to +90C (vs. LC4128V-75TN100I)
- Wider 1.8V I/O support than 4000B predecessor (vs. LC4128B-75TN100C)
Designhinweise
Route at least one solid GND and one VCC plane directly under the TQFP-100 land pattern; place 0.1uF X7R ceramic decoupling caps within 100 mil of every VCC and VCCIO pin (4 caps total minimum on a 100-pin package). Long VCC traces introduce switching noise that couples into the I/O banks and degrades the 400 MHz fMAX. Estimated: 4 decoupling caps plus one 10uF bulk cap per rail will keep power-rail impedance below 50 mOhm through 100 MHz per standard capacitor-impedance guidelines.
Do not leave unused I/O pins floating. Configure unused pins as outputs driving low or as inputs with internal pull-ups enabled in the Lattice ispLEVER design tool. Floating inputs on E2CMOS CPLDs can draw several hundred microamps each through the input buffer, potentially pulling Icc above the 50 mA commercial-spec limit and triggering thermal shutdown at high ambient temperatures. Unused JTAG pins (TCK/TMS/TDI/TDO) should be tied to known logic states if not used for boundary scan.
Match the bank VCCIO supply to the highest-voltage I/O standard used in that bank. Mixing 1.8V and 3.3V signals in the same bank is undefined behavior and can permanently damage the output drivers. For designs that must bridge 3.3V and 1.8V, use a dedicated level-translator IC such as the TXS0108E between the CPLD and the 1.8V device. The ispMACH 4000V supports 1.8V/2.5V/3.3V mixed-voltage designs only if each bank is independently powered.
Estimated: at 400 MHz toggle rate on all 64 outputs simultaneously loaded with 10 pF each, the LC4128V-75TN100C dissipates approximately 0.5-0.8 W. The TQFP-100 package has theta_JA of approximately 50 C/W on a 4-layer JEDEC test board, resulting in a junction temperature rise of 25-40 C above ambient. In enclosed industrial enclosures at 60 C ambient, derate fMAX by 10-15% or add a copper thermal pad under the exposed die flag.
Compliance-Informationen
RoHS-compliant per Lattice product page. The "N" suffix in the ordering code confirms lead-free terminal finish. AEC-Q100 not qualified - this is a commercial-grade part; the LC4128V-75TN100I is the industrial temperature grade but still not AEC-Q100 automotive qualified.
