LM224DG - 4-Channel 1 MHz Op Amp | onsemi | Industrial Control
Teilenummer: LM224DG ✓ AktivLM224DG Übersicht
An operational amplifier is a high-gain differential-input amplifier commonly used to buffer sensors, amplify small signals, implement active filters, and drive higher-impedance loads. The LM224 belongs to the operational-amplifier hierarchy, which includes voltage-feedback amplifiers and is used within analog signal-chain and power-management systems. Its four channels can be used independently when the required circuit functions do not interfere.
Key verified features include four amplifier circuits, a 1 MHz gain-bandwidth product, a 3 V to 32 V operating supply range, true differential inputs, and a minimum common-mode rejection ratio of 70 dB. The listed input-offset voltage is 5 mV. These characteristics make the LM224DG appropriate for general-purpose signal conditioning where a wide supply range and multiple analog channels are more important than precision or low-noise performance.
The LM224 series is designed for low-cost, general-purpose applications and supports operation from a single power supply or split supplies. This flexibility allows engineers to interface signals around ground or operate from an industrial supply without requiring negative rails. Its internal frequency compensation simplifies closed-loop amplifier design, although stable operation still depends on suitable feedback networks and load conditions described by the manufacturer.
Typical applications include sensor-signal conditioning, current-loop measurement, industrial process-control modules, data-acquisition systems, and general test equipment. The 14-pin SOIC package is also convenient for through-hole assembly and conventional hand-soldering. Because the LM224 is a general-purpose amplifier, precision instrumentation may require careful offset, bias-current, noise, and common-mode analysis before finalizing the signal chain.
When designing around the LM224DG, verify input and output voltage limits for the selected dual or single supply, check that connected loads remain within the amplifier's drive capability, and reserve suitable bypass capacitance close to the supply pins. Stable feedback and compensation arrangements should be copied from the manufacturer datasheet rather than copied blindly from unrelated op-amp circuits.
This page combines the verified distributor and manufacturer-linked information for LM224DG with same-package drop-in alternatives, comparison parameters, and practical selection guidance. It highlights where the LM224's wide supply range and four-channel integration are useful, while making uncertainty in unavailable electrical details explicit.
Drop-in-Alternativen für LM224DG – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM224DG (gleiche Bauform und Footprint) – abweichend in Package, Amplifier Type, Input Offset Voltage, Input Type, Product Type.
LM224NG
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LM224DR
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LM324DG
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LM324D
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM2902D
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →LM224DG Grenzwerte & elektrische Eigenschaften
| Product Type | Quad operational amplifier |
| Number of Channels | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz |
| Supply Voltage Range | 3 V to 32 V |
| Input Offset Voltage | 5 mV |
| Common-Mode Rejection Ratio | 70 dB minimum |
| Input Type | True differential inputs |
| Supply Configuration | Single supply or split supply |
| Compensation | Internally frequency compensated |
| Gehäuse | 14-pin SOIC, 0.154 inch (3.90 mm) width |
| Montageart | Surface mount |
| Betriebstemperaturbereich | -25 C to +85 C |
LM224DG 14-pin soic, 0.154 inch (3.90 mm) width Pinbelegungsleitfaden
Pinbelegung für LM224DG (14-pin soic, 0.154 inch (3.90 mm) width-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für LM224DG.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
LM224DG ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Data Acquisition and Instrumentation, Current Loop and Process Control, Power Supply Feedback and Monitoring, Audio and Low-Frequency Signal Conditioning, Test and Measurement Equipment.
Industrial Sensor Signal Conditioning
The LM224DG fits general-purpose industrial sensor interfaces because it combines four true-differential-input amplifiers with a 3 V to 32 V supply range in one 14-SOIC package. Multiple channels can condition related inputs without requiring four separate amplifier packages, reducing board area and simplifying routing. Its 1 MHz gain-bandwidth product is suitable for moderate-bandwidth signals, while the listed 70 dB minimum CMRR helps suppress common-mode interference. Engineers should still verify the sensor output range against the amplifier's common-mode limits and assess the 5 mV listed input offset at the required gain.
Empfohlen
Data Acquisition and Instrumentation
The LM224DG can provide the basic amplification and buffering stages required by multi-channel data-acquisition and instrumentation equipment. Its four independent amplifiers support parallel measurement channels, and the 14-SOIC package is straightforward for conventional PCB assembly. A 1 MHz gain-bandwidth product is appropriate for many low-to-moderate-frequency sensor signals rather than high-speed waveform acquisition. Designers should pay particular attention to input offset, drift, input bias behavior, and output settling because the verified LM224DG information identifies a 5 mV input-offset value but does not provide a complete precision-noise specification.
Empfohlen
Current Loop and Process Control
The LM224DG is applicable to basic current-loop and process-control interfaces where multiple analog channels must operate from an industrial-style supply. The 3 V to 32 V range allows operation from higher-voltage control rails, and split-supply support is useful when signals are centered around ground. Its internally frequency-compensated architecture simplifies the construction of conventional closed-loop amplifier stages. For process-control accuracy, however, engineers should verify offset and bias-current contributions, output-current requirements, common-mode range, and stability with the actual transmitter load before selecting it as the final amplifier.
Empfohlen
Power Supply Feedback and Monitoring
The LM224DG can be used in power-supply feedback, supervision, and analog monitoring circuits where several ratios or sensing channels are required. Its wide 3 V to 32 V operating range covers many industrial and distributed-supply environments, while true differential inputs assist with measurements referenced to a remote or local return. Because the device is a general-purpose amplifier, the design should include adequate supply bypassing and account for input offset when monitoring small feedback voltages. The selected amplifier must remain within its input and output common-mode limits throughout startup, overload, and fault conditions.
Empfohlen
Audio and Low-Frequency Signal Conditioning
The LM224DG can handle general low-frequency audio and control-signal conditioning where four channels and a wide supply range are useful. The internally compensated amplifier supports standard inverting and non-inverting configurations, while the 1 MHz gain-bandwidth product is more than adequate for many low-frequency audio functions. This device should not be assumed to provide the low-noise performance of a dedicated audio amplifier: the verified excerpts do not supply an output-noise rating. Use the manufacturer noise data and output-drive limits when designing microphone preamplifiers, headphone stages, or audio distribution networks.
Empfohlen
Test and Measurement Equipment
The LM224DG is suited to inexpensive test and measurement modules requiring several general-purpose amplifier sections. Four channels in a 14-SOIC package allow measurement buffers, attenuators, active filters, and differential input stages to share one component. The 1 MHz gain-bandwidth product supports many bench and embedded test signals, while true differential inputs simplify rejection of common-mode voltage on balanced or floating probes. The design should account for the listed 5 mV input offset when low-level accuracy matters and verify output swing, load compatibility, and temperature behavior using the full manufacturer datasheet.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM224DG – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM224NG | LM224DR | LM324DG | LM324D | LM2902D |
|---|---|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 2 |
Wichtigste Unterscheidungsmerkmale
- Four integrated amplifier channels (vs. LM2902D)
- Wide single-supply operating range (vs. LM324D)
- Established onsemi LM224-family sourcing (vs. LM324D)
- True differential inputs (vs. LM2902D)
Designhinweise
Place the supply bypass capacitor close to the device's supply and ground pins and keep the return-current path short. The LM224 supports single-supply and split-supply operation, but the usable input and output range depends on the selected rail arrangement. Confirm the actual signal range, output swing, and supply limits from the manufacturer datasheet rather than assuming that the full 3 V to 32 V input range can also be used as signal swing.
Do not substitute a dual amplifier for the LM224DG without accounting for the reduced channel count. The LM2902D alternative uses two packages for four amplifiers, requiring layout changes even though both devices use 14-SOIC packages. Likewise, verify each alternative's pinout and offset specification. A shared package and similar family name do not guarantee identical gain, bias current, common-mode range, output drive, or temperature grade.
Route each amplifier's input, feedback components, and output according to the datasheet's recommended topology. Keep sensitive input traces away from supply-switching nodes and output nodes that may drive capacitive loads. Use a stable reference point for both inputs of a differential stage, and evaluate offset contributions from the listed 5 mV input-offset specification at the selected closed-loop gain before treating the LM224DG as a precision measurement amplifier.
Compliance-Informationen
The supplied excerpts reference RoHS information but do not provide an explicit compliance conclusion. No verified REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was provided, so these fields remain unknown.
