onsemi

LM2902DTB - Quad 3-26V Op Amp, 14-TSSOP | onsemi

Teilenummer: LM2902DTB ✓ Aktiv
3 V to 26 V Vdss 14-TSSOP Package
MOQ: 1 |

LM2902DTB Übersicht

The onsemi LM2902DTB is a general-purpose quad operational amplifier packaged in a 14-pin TSSOP. It supports a 3 V to 26 V supply range and integrates four amplifier channels, allowing one compact device to implement four independent analog signal-conditioning paths. The LM2902 family is designed for low-cost single-supply equipment where true differential inputs and common-mode operation are useful.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. The quad configuration belongs to the hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. True differential inputs allow the amplifier to respond to two input signals rather than requiring both signals to be referenced to ground, making the device useful in sensor, transducer, and feedback networks.

The LM2902 family combines a 3 V to 26 V supply range with low quiescent-current operation and a 1.2 MHz unity-gain bandwidth. Its input offset voltage is specified at 2 mV, while the four-channel architecture reduces the number of packages and board-area requirements compared with four separate single amplifiers. These characteristics suit general-purpose analog designs where cost, supply flexibility, and practical integration matter more than precision or rail-to-rail performance.

Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style interface, or feedback element in a control loop. The device does not reach the positive or negative supply rail at its output, so analog output ranges must be checked against the selected supply voltage and load. Input common-mode range, output swing, input bias current, and noise remain important constraints when precision or high-impedance source designs are required.

Typical uses include industrial sensor interfaces, low-cost instrumentation, audio preamplifier stages, active filtering, relay-driver signal conditioning, and general-purpose control boards. A four-channel implementation is especially attractive when several sensors require similar conditioning or when a system needs independent amplifier channels for measurement, monitoring, and feedback.

PCB implementation should follow the manufacturer pinout and recommended decoupling guidance. Place the supply bypass capacitor close to the power pins, route sensitive input and feedback traces away from switching nodes, and use a common ground plane with short return paths. Because the outputs cannot swing fully to either rail, applications needing rail-to-rail operation require a different amplifier family.

This page combines the LM2902DTB package and supply information with engineering-focused application guidance, replacement criteria, and a parameter comparison. These details help engineers determine when the quad topology simplifies a design and where a single, rail-to-rail, or higher-precision amplifier is the better choice.

Drop-in-Alternativen für LM2902DTB – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902DTB (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Amplifier Type, Number of Amplifier Channels, Supply Voltage Range.

STMicroelectronics
Package: 14-SO
Amplifier Type: General-purpose operational amplifier
Vergleichen mit LM2902DTB →
Texas Instruments
Package: 14-pin SOIC
Amplifier Type: Quad general-purpose operational amplifier
Vergleichen mit LM2902DTB →
onsemi
Package: 14-pin SOP
Product Type: General-purpose operational amplifier
Vergleichen mit LM2902DTB →
onsemi
Package: 14-TSSOP
Number of Amplifier Channels: 4 circuits
Vergleichen mit LM2902DTB →
onsemi
Product Type: Single-supply quad operational amplifier
Vergleichen mit LM2902DTB →
onsemi
Product Type: Quad general-purpose operational amplifier
Vergleichen mit LM2902DTB →
STMicroelectronics
Package: 14-SOIC
Supply Voltage Range: 3 V to 32 V
Vergleichen mit LM2902DTB →
Texas Instruments
Package: 8-pin SOIC
Product Type: Dual general-purpose operational amplifier
Amplifier Type: Standard general-purpose amplifier
Vergleichen mit LM2902DTB →

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

LM2902DTB Grenzwerte & elektrische Eigenschaften

Product Type Quad operational amplifier
Manufacturer onsemi
Supply Voltage Range 3 V to 26 V
Number of Amplifier Channels 4 circuits
Gehäuse 14-TSSOP
Montageart Surface mount
Unity-Gain Bandwidth 1.2 MHz
Input Offset Voltage 2 mV
Input Configuration True differential inputs
Supply Configuration Single supply

LM2902DTB 14-tssop Pinbelegungsleitfaden

Pinbelegung für LM2902DTB (14-tssop-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für LM2902DTB im 14-tssop-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für LM2902DTB.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

LM2902DTB ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Audio Preamplifier And Mixer, Active Filter And Control Loops, Data Acquisition And Monitoring, Relay And Interface Signal Conditioning, Portable Battery-Powered Instrumentation.

🏭

Industrial Sensor Signal Conditioning

The LM2902DTB is appropriate for low-frequency industrial sensor interfaces because four true-differential amplifier channels can condition several inputs within one 14-TSSOP package. Its 3 V to 26 V supply range supports both low-voltage sensor systems and higher-voltage control boards. A designer can use the channels for instrumentation-style differential amplification, gain stages, active filters, or buffer isolation. The approximately 1.2 MHz unity-gain bandwidth is well above many process-control signal bandwidths, while the 2 mV input offset must be included in the overall measurement-error budget. Source impedance, common-mode range, and output swing should be checked before finalizing the sensor interface.

🎧

Audio Preamplifier And Mixer

Four integrated amplifier channels give the LM2902DTB value in small audio preamplifier and mixing boards. Each channel can provide voltage gain, input buffering, tone shaping, or a simple active-filter function, and the 1.2 MHz unity-gain bandwidth comfortably covers conventional audio-band signals. The single-supply architecture simplifies portable and low-cost audio equipment, but output headroom must be designed around the device's non-rail-to-rail output behavior. For low-impedance headphone or line outputs, check current capability and distortion in the LM2902 family datasheet before the output stage is finalized.

🔧

Active Filter And Control Loops

The LM2902DTB is suitable for modest-bandwidth active-filter and control-loop implementations using its four channels. At approximately 1.2 MHz unity-gain bandwidth, the device can form first- or second-order signal-conditioning sections, but stable closed-loop operation depends on the selected noise gain and component tolerances. The 2 mV input offset may be significant in precision filter applications, particularly when signal amplitudes are small. A common 14-TSSOP footprint also helps consolidate four loop elements onto one board, although the chosen feedback and compensation networks must remain within the amplifier's stability limits.

📊

Data Acquisition And Monitoring

The LM2902DTB can serve as the front-end amplifier for compact data-acquisition and monitoring equipment that processes four low-frequency channels. True differential inputs simplify connection of Wheatstone-style bridges or differential sensors, while the 3 V to 26 V operating range allows the amplifier to operate from either compact sensor rails or a larger control-system supply. The four-channel package reduces component count, while the approximately 1.2 MHz bandwidth is suitable for many slowly varying process and environmental measurements. Input bias current and common-mode limits should be checked for high-impedance sensors, and the 2 mV offset should be included in calibration and error analysis.

⚡

Relay And Interface Signal Conditioning

The LM2902DTB is useful for conditioning low-level logic, sensor, or contact-status signals before they reach a controller or relay-driver stage. Its four channels can independently buffer, invert, or apply gain, reducing the number of discrete amplifier packages in a multi-channel interface board. The single 3 V to 26 V supply simplifies integration into industrial control electronics, but the output must remain within the amplifier's specified swing rather than being assumed to reach the supply rail. Input transients should be limited using appropriate source impedance or protection, and the TSSOP layout should preserve clean ground returns to prevent coupled noise from disturbing adjacent channels.

🔋

Portable Battery-Powered Instrumentation

The LM2902DTB fits portable battery-powered instrumentation when several low-frequency analog paths must share a compact board. A 3 V minimum supply supports operation from a single low-voltage cell or regulated rail, while low-power operation is emphasized in the LM324-series operating characteristics described by onsemi. Four channels can reduce board area compared with separate single amplifiers, although unused channels and external biasing can affect total power consumption. The non-rail-to-rail output swing should be accommodated in the signal chain, and input and output ranges should be evaluated at the lowest battery voltage to avoid clipping.

Zusammenfassung der empfohlenen Produkte

LM2902D Texas Instruments Verwendet in: Industrial Sensor Signal Conditioning, Audio Preamplifier And Mixer, Data Acquisition And Monitoring, Portable Battery-Powered Instrumentation LM324 Quad operational-amplifier functional comparison Verwendet in: Industrial Sensor Signal Conditioning, Active Filter And Control Loops, Data Acquisition And Monitoring, Portable Battery-Powered Instrumentation LM358 Related dual-amplifier alternative for two-channel signal conditioning Verwendet in: Industrial Sensor Signal Conditioning, Audio Preamplifier And Mixer, Relay And Interface Signal Conditioning, Portable Battery-Powered Instrumentation LM393 Texas Instruments Verwendet in: Audio Preamplifier And Mixer, Data Acquisition And Monitoring, Relay And Interface Signal Conditioning LM2902-N LM2902-family amplifier option for alternative sourcing review Verwendet in: Active Filter And Control Loops, Relay And Interface Signal Conditioning LM335 Analog reference option for biasing or threshold networks Verwendet in: Active Filter And Control Loops
What is the operating voltage of LM2902DTB?
The LM2902DTB operates from a 3 V to 26 V single supply. This range allows it to be used in low-voltage equipment and in systems with higher supply rails without requiring separate positive and negative analog supplies. According to the onsemi LM2902 family datasheet, the device uses true differential inputs and is intended for general-purpose low-cost amplifier applications. Verify the complete operating-temperature, input common-mode, and output-swing limits before using the amplifier at the extremes of the supply range.
How many operational amplifiers are in the LM2902DTB?
The LM2902DTB contains four independent operational-amplifier channels in one 14-pin TSSOP package. Each channel can implement a separate signal path, such as a sensor amplifier, active filter, comparator interface, or feedback amplifier. The onsemi LM2902 family datasheet identifies the device as a single-supply quad operational amplifier with true differential inputs. Combining four channels can reduce board area and component count, but each amplifier still requires the correct power, feedback, decoupling, and output-load connections.
What is the LM2902DTB bandwidth and input offset voltage?
The LM2902 family is specified at a 1.2 MHz unity-gain bandwidth and a 2 mV input offset voltage. Bandwidth determines the highest useful closed-loop signal frequency for a given gain and noise-gain topology, while input offset voltage contributes directly to output error. According to the manufacturer datasheet, these figures make the device suitable for general-purpose audio, control, and instrumentation stages. They should not be treated as precision-rail-to-rail specifications, especially when input offset or small-signal accuracy dominates the design.
Is LM2902DTB a drop-in replacement for LM324?
The LM2902DTB can be considered only after its package, pinout, supply range, and electrical limits are matched to the specific LM324 variant. The LM2902 family is described as a single-supply quad amplifier with true differential inputs, but an LM324 may be offered in several package configurations. According to the onsemi and TI datasheets, designers must compare the ordered suffix and footprint rather than assume that every quad op amp is interchangeable. A 14-TSSOP target board requires a candidate specifically offered in a pin-compatible 14-TSSOP package.
Can LM2902DTB drive a load near the supply rails?
No, the LM2902DTB should not be assumed to produce an output at either supply rail. Its output swing is constrained by the internal transistor architecture, even though the device accepts a 3 V to 26 V supply. The onsemi LM2902 family datasheet should be consulted for the output-voltage versus output-current curves. If the application requires a nearly 0 V or nearly supply-voltage output, select an amplifier explicitly specified for rail-to-rail output instead of relying on extra supply headroom.
Where can I download the LM2902DTB datasheet PDF?
The LM2902DTB datasheet and product details can be found through the onsemi LM2902 documentation linked from the component's manufacturer product page. The available datasheet index for this MPN identifies the document as the onsemi LM2902DTB single-supply quad operational-amplifier datasheet. Use the document's pin-description table and electrical-characteristics tables when assigning PCB pins, selecting bypass capacitors, and confirming input common-mode, output-swing, and supply-current limits.
Where can I find the LM2902DTB pinout?
The LM2902DTB pinout is located in the pin-configuration section of the onsemi LM2902 family datasheet for the 14-TSSOP package. The package contains four amplifier channels, supply pins, and ground connections, so the numbered diagram must be used rather than assuming a generic op-amp arrangement. Before routing a PCB, verify pin numbering against the specific package drawing and preserve exposed-pad or thermal requirements if the ordering variant includes them.
LM2902DTB vs LM2902D - which is better for a TSSOP PCB?
The LM2902DTB is the appropriate choice for the 14-TSSOP footprint because its listing identifies a 14-pin TSSOP package. The TI LM2902D is listed in a 14-SOIC package, so its footprint and pin geometry differ even though both devices belong to the general LM2902 family. According to the manufacturer product information, both are described as quad, 26 V, 1.2 MHz, 2 mV-offset operational amplifiers. Use LM2902DTB for the TSSOP design and LM2902D only when a new SOIC footprint is acceptable.
When should I choose LM2902DTB over a single or dual op amp?
Choose the LM2902DTB when the design needs four general-purpose amplifier channels and can accept a 14-pin TSSOP footprint. Its 3 V to 26 V supply range and 1.2 MHz unity-gain bandwidth are useful for conventional signal-conditioning and control paths. A single amplifier is preferable when only one channel is required, while a dual amplifier may reduce unused circuitry in two-channel designs. The four-channel device becomes advantageous only when all four channels can be used and board-space savings outweigh unused-channel considerations.
What can replace LM2902DTB?
A valid LM2902DTB replacement must be a quad operational amplifier in a pin-compatible 14-TSSOP package with compatible power, input, output, and compensation characteristics. The 3 V to 26 V supply range and approximately 1.2 MHz bandwidth of the LM2902 family define the baseline, while the 2 mV input offset specification should also be checked. According to the LM2902 family datasheet, package and ordering suffix must be considered together; a functionally similar amplifier in SOIC, VSSOP, or another package is not a PCB drop-in replacement.
Is LM2902DTB suitable for sensor signal conditioning?
The LM2902DTB is suitable for many low-frequency sensor signal-conditioning applications that operate within its input common-mode and output-swing limits. Its true differential inputs support bridge, differential, and feedback-amplifier configurations, while the 1.2 MHz unity-gain bandwidth covers common audio, control, and instrumentation frequencies. The onsemi LM2902 family datasheet should be checked for input bias current and noise when the source impedance is high. High-impedance or precision sensors may require a lower-offset, lower-bias-current amplifier.
Where to buy LM2902DTB online?
Use the Request a Quote form on this page to request LM2902DTB availability, lead time, order quantity, and shipment options. The form is the appropriate commercial channel for this quote-oriented product page and lets the purchasing team confirm the exact 14-TSSOP ordering suffix. When requesting a quotation, state the required quantity, target date, and whether reel, cut-tape, or another approved delivery format is needed so material planning and procurement can respond accurately.
What is the price of LM2902DTB?
The current commercial price and available quantity for LM2902DTB should be obtained through the Request a Quote form on this page. A quotation confirms the exact package suffix, order break, delivery format, and current supply conditions without embedding a price that may change. For engineering budgeting, the structured pricing fields should be consulted separately from technical claims. When requesting a quote, include the required annual and production quantities so procurement can identify the appropriate supply arrangement.
What is the lead time for LM2902DTB?
The current lead time for LM2902DTB should be confirmed through the Request a Quote form on this page with the required quantity and target delivery date. Lead time can vary with order volume, scheduled production, and the requested shipping format. Because the part is offered as a 14-TSSOP device, the quotation should also confirm reel or cut-tape availability. For long-lead projects, request the material schedule before releasing the final PCB assembly order.
Is LM2902DTB in stock?
Current LM2902DTB stock should be checked through the Request a Quote form on this page because inventory changes with production and fulfillment activity. Submit the required quantity, package delivery preference, target date, and destination country with the request. Procurement can then confirm available inventory, scheduled supply, and lead time for the exact LM2902DTB suffix. For safety- or availability-sensitive builds, request a buffer quantity rather than relying on an unconfirmed stock position.
What are the key specifications of LM2902DTB that engineers should know?
The key LM2902DTB specifications are four amplifier channels, a 3 V to 26 V supply range, a 14-TSSOP package, approximately 1.2 MHz unity-gain bandwidth, 2 mV input offset voltage, true differential inputs, and single-supply operation. According to the onsemi LM2902 family datasheet and current manufacturer product information, these characteristics place it in the general-purpose low-cost quad-amplifier class. Design reviews should also verify input common-mode range, output swing, bias current, noise, and temperature limits for the selected ordering variant.

Technische Referenzdaten für LM2902DTB – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose LM2902DTB when a design needs four general-purpose linear amplifier channels in a 14-TSSOP package and can operate from a 3 V to 26 V single supply. Its approximately 1.2 MHz unity-gain bandwidth and true differential inputs suit low-frequency sensor conditioning, audio preamplification, active filtering, and general control interfaces. Choose a single amplifier when only one channel is required or a dual amplifier such as the LM358 family when two channels suffice. LM2902D provides the same broad quad-amplifier function but uses a 14-SOIC footprint, so it requires a different PCB layout. LM393 is appropriate for threshold and comparator functions, not linear amplification. For precision, very-low-offset, high-impedance-source, or rail-to-rail-output requirements, select a dedicated precision or rail-to-rail amplifier instead. Before release, verify the exact package pinout, common-mode range, output swing, stability, and temperature limits.

Vergleich mit Alternativen

Parameter Dieses Produkt
Package 14-TSSOP
Brand onsemi
Product Type Quad operational amplifier
Number of Channels 4 circuits
Supply Voltage Range 3 V to 26 V
Unity-Gain Bandwidth 1.2 MHz
Input Offset Voltage 2 mV
Input Configuration True differential inputs
Mounting Type Surface mount

Wichtigste Unterscheidungsmerkmale

  • Four amplifiers are integrated in one compact package (vs. LM2902D)
  • Wide single-supply operating range (vs. LM358)
  • Differential input capability for general-purpose analog conditioning (vs. LM393)

Designhinweise

Place the supply bypass capacitor immediately adjacent to the LM2902DTB power and ground pins, with the shortest possible traces. Decouple each amplifier section according to the manufacturer layout guidance when the four channels drive separated signal paths. Check source current at the minimum operating supply of 3 V and at maximum load because the amplifier does not provide rail-to-rail output swing. Keep external current draws and sensor loads off the analog supply node so their transients do not disturb the quad amplifier.

Route each non-inverting input, feedback component, and output as a compact analog channel, especially where small sensor signals are amplified. Connect the exposed ground return to a continuous ground plane and keep switching-regulator, relay, and digital timing nodes away from the input pins. Maintain the package's standard pin numbering when laying out the 14-TSSOP footprint and confirm every amplifier channel's supply connection against the manufacturer diagram before fabrication.

Do not treat the 3 V to 26 V supply capability as permission to swing the output fully to either rail, and do not assume the input can accept every voltage between the supply limits. Review common-mode range, output swing, input bias current, and stability for the actual gain network. For high-impedance sources, high precision, or very small output signals, the 2 mV input offset and 1.2 MHz bandwidth may be unsuitable; choose a more specialized amplifier instead of forcing the LM2902DTB beyond its intended class.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The onsemi LM2902 family datasheet and product documentation should be checked for the latest environmental declarations and ordering-specific qualification information. No automotive qualification is established for the standard LM2902DTB ordering option.

Daten verifiziert am: 2026-11-17 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

LM2902DTB datasheet LM2902DTB pinout LM2902DTB datasheet pdf LM2902DTB 14-TSSOP LM2902DTB 3-26V amplifier LM2902DTB 1.2MHz bandwidth onsemi LM2902DTB LM2902DTB equivalent LM2902DTB replacement LM2902DTB cross reference LM2902DTB footprint LM2902DTB price LM2902DTB stock LM2902DTB vs LM2902D

Verwandte Bauteile & Begriffe

onsemi LM2902DTB LM2902D LM2902-N LM2902PT LM2902DTBR2G LM324 LM335 LM358 LM393 quad operational amplifier operational amplifier analog amplifier analog signal-conditioning IC true differential input single supply 3 V to 26 V supply 1.2 MHz unity-gain bandwidth 2 mV input offset voltage common-mode input range output voltage swing 14-TSSOP TSSOP package family surface-mount package SMD
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen