LM2902DTB - Quad 3-26V Op Amp, 14-TSSOP | onsemi
N.º de pieza: LM2902DTB ✓ ActivoLM2902DTB Descripción general
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs. The quad configuration belongs to the hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. True differential inputs allow the amplifier to respond to two input signals rather than requiring both signals to be referenced to ground, making the device useful in sensor, transducer, and feedback networks.
The LM2902 family combines a 3 V to 26 V supply range with low quiescent-current operation and a 1.2 MHz unity-gain bandwidth. Its input offset voltage is specified at 2 mV, while the four-channel architecture reduces the number of packages and board-area requirements compared with four separate single amplifiers. These characteristics suit general-purpose analog designs where cost, supply flexibility, and practical integration matter more than precision or rail-to-rail performance.
Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style interface, or feedback element in a control loop. The device does not reach the positive or negative supply rail at its output, so analog output ranges must be checked against the selected supply voltage and load. Input common-mode range, output swing, input bias current, and noise remain important constraints when precision or high-impedance source designs are required.
Typical uses include industrial sensor interfaces, low-cost instrumentation, audio preamplifier stages, active filtering, relay-driver signal conditioning, and general-purpose control boards. A four-channel implementation is especially attractive when several sensors require similar conditioning or when a system needs independent amplifier channels for measurement, monitoring, and feedback.
PCB implementation should follow the manufacturer pinout and recommended decoupling guidance. Place the supply bypass capacitor close to the power pins, route sensitive input and feedback traces away from switching nodes, and use a common ground plane with short return paths. Because the outputs cannot swing fully to either rail, applications needing rail-to-rail operation require a different amplifier family.
This page combines the LM2902DTB package and supply information with engineering-focused application guidance, replacement criteria, and a parameter comparison. These details help engineers determine when the quad topology simplifies a design and where a single, rail-to-rail, or higher-precision amplifier is the better choice.
Alternativas directas para LM2902DTB — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM2902DTB (mismo factor de forma y huella) — difiere en Package, Product Type, Amplifier Type, Number of Amplifier Channels, Supply Voltage Range.
No hay alternativas directas disponibles para este producto.
Solicitar alternativasLM2902DTB Valores máximos y características eléctricas
| Product Type | Quad operational amplifier |
| Manufacturer | onsemi |
| Supply Voltage Range | 3 V to 26 V |
| Number of Amplifier Channels | 4 circuits |
| Encapsulado | 14-TSSOP |
| Tipo de montaje | Surface mount |
| Unity-Gain Bandwidth | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Input Configuration | True differential inputs |
| Supply Configuration | Single supply |
Guía de configuración de pines de LM2902DTB 14-tssop
Configuración de pines para LM2902DTB (encapsulado 14-tssop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM2902DTB.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM2902DTB es adecuado para 6 aplicacións: Industrial Sensor Signal Conditioning, Audio Preamplifier And Mixer, Active Filter And Control Loops, Data Acquisition And Monitoring, Relay And Interface Signal Conditioning, Portable Battery-Powered Instrumentation.
Industrial Sensor Signal Conditioning
The LM2902DTB is appropriate for low-frequency industrial sensor interfaces because four true-differential amplifier channels can condition several inputs within one 14-TSSOP package. Its 3 V to 26 V supply range supports both low-voltage sensor systems and higher-voltage control boards. A designer can use the channels for instrumentation-style differential amplification, gain stages, active filters, or buffer isolation. The approximately 1.2 MHz unity-gain bandwidth is well above many process-control signal bandwidths, while the 2 mV input offset must be included in the overall measurement-error budget. Source impedance, common-mode range, and output swing should be checked before finalizing the sensor interface.
Recomendado
Audio Preamplifier And Mixer
Four integrated amplifier channels give the LM2902DTB value in small audio preamplifier and mixing boards. Each channel can provide voltage gain, input buffering, tone shaping, or a simple active-filter function, and the 1.2 MHz unity-gain bandwidth comfortably covers conventional audio-band signals. The single-supply architecture simplifies portable and low-cost audio equipment, but output headroom must be designed around the device's non-rail-to-rail output behavior. For low-impedance headphone or line outputs, check current capability and distortion in the LM2902 family datasheet before the output stage is finalized.
Recomendado
Active Filter And Control Loops
The LM2902DTB is suitable for modest-bandwidth active-filter and control-loop implementations using its four channels. At approximately 1.2 MHz unity-gain bandwidth, the device can form first- or second-order signal-conditioning sections, but stable closed-loop operation depends on the selected noise gain and component tolerances. The 2 mV input offset may be significant in precision filter applications, particularly when signal amplitudes are small. A common 14-TSSOP footprint also helps consolidate four loop elements onto one board, although the chosen feedback and compensation networks must remain within the amplifier's stability limits.
Recomendado
Data Acquisition And Monitoring
The LM2902DTB can serve as the front-end amplifier for compact data-acquisition and monitoring equipment that processes four low-frequency channels. True differential inputs simplify connection of Wheatstone-style bridges or differential sensors, while the 3 V to 26 V operating range allows the amplifier to operate from either compact sensor rails or a larger control-system supply. The four-channel package reduces component count, while the approximately 1.2 MHz bandwidth is suitable for many slowly varying process and environmental measurements. Input bias current and common-mode limits should be checked for high-impedance sensors, and the 2 mV offset should be included in calibration and error analysis.
Recomendado
Relay And Interface Signal Conditioning
The LM2902DTB is useful for conditioning low-level logic, sensor, or contact-status signals before they reach a controller or relay-driver stage. Its four channels can independently buffer, invert, or apply gain, reducing the number of discrete amplifier packages in a multi-channel interface board. The single 3 V to 26 V supply simplifies integration into industrial control electronics, but the output must remain within the amplifier's specified swing rather than being assumed to reach the supply rail. Input transients should be limited using appropriate source impedance or protection, and the TSSOP layout should preserve clean ground returns to prevent coupled noise from disturbing adjacent channels.
Recomendado
Portable Battery-Powered Instrumentation
The LM2902DTB fits portable battery-powered instrumentation when several low-frequency analog paths must share a compact board. A 3 V minimum supply supports operation from a single low-voltage cell or regulated rail, while low-power operation is emphasized in the LM324-series operating characteristics described by onsemi. Four channels can reduce board area compared with separate single amplifiers, although unused channels and external biasing can affect total power consumption. The non-rail-to-rail output swing should be accommodated in the signal chain, and input and output ranges should be evaluated at the lowest battery voltage to avoid clipping.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM2902DTB — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Package | 14-TSSOP |
| Brand | onsemi |
| Product Type | Quad operational amplifier |
| Number of Channels | 4 circuits |
| Supply Voltage Range | 3 V to 26 V |
| Unity-Gain Bandwidth | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Input Configuration | True differential inputs |
| Mounting Type | Surface mount |
Diferenciadores clave
- Four amplifiers are integrated in one compact package (frente a LM2902D)
- Wide single-supply operating range (frente a LM358)
- Differential input capability for general-purpose analog conditioning (frente a LM393)
Notas de diseño
Place the supply bypass capacitor immediately adjacent to the LM2902DTB power and ground pins, with the shortest possible traces. Decouple each amplifier section according to the manufacturer layout guidance when the four channels drive separated signal paths. Check source current at the minimum operating supply of 3 V and at maximum load because the amplifier does not provide rail-to-rail output swing. Keep external current draws and sensor loads off the analog supply node so their transients do not disturb the quad amplifier.
Route each non-inverting input, feedback component, and output as a compact analog channel, especially where small sensor signals are amplified. Connect the exposed ground return to a continuous ground plane and keep switching-regulator, relay, and digital timing nodes away from the input pins. Maintain the package's standard pin numbering when laying out the 14-TSSOP footprint and confirm every amplifier channel's supply connection against the manufacturer diagram before fabrication.
Do not treat the 3 V to 26 V supply capability as permission to swing the output fully to either rail, and do not assume the input can accept every voltage between the supply limits. Review common-mode range, output swing, input bias current, and stability for the actual gain network. For high-impedance sources, high precision, or very small output signals, the 2 mV input offset and 1.2 MHz bandwidth may be unsuitable; choose a more specialized amplifier instead of forcing the LM2902DTB beyond its intended class.
Información de cumplimiento
The onsemi LM2902 family datasheet and product documentation should be checked for the latest environmental declarations and ordering-specific qualification information. No automotive qualification is established for the standard LM2902DTB ordering option.