Texas Instruments

LM2902MT/NOPB - Quad 26V Op Amp in 14-TSSOP | TI

Teilenummer: LM2902MT/NOPB ✗ Abgekündigt
26 V Vdss 14-TSSOP Package
MOQ: 1 |

LM2902MT/NOPB Übersicht

Texas Instruments LM2902MT/NOPB is a quad, general-purpose operational amplifier designed for a 26 V maximum supply and a 1.2 MHz gain-bandwidth product. The device contains four independent amplifier sections in a 14-pin TSSOP package, with an operating temperature range of -40°C to 85°C for this ordering option.

A general-purpose operational amplifier is a voltage-amplified analog building block that compares an input voltage with a feedback-derived reference voltage. The quad LM2902 combines four amplifiers in one package, reducing component count and board area in sensor, control, and signal-conditioning designs. Its four amplifiers share a common supply architecture but maintain independent differential inputs and outputs.

Key features include a 26 V maximum total supply voltage, approximately 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage as identified by Texas Instruments. The low-power architecture is suited to industrial and embedded systems operating from a single supply or split supplies. Four amplifiers in one thermal package also simplify component stocking and reduce the PCB footprint required for multiple amplifier sections.

The LM2902 family uses a low-power bipolar process and provides general-purpose amplification rather than precision or high-speed performance. Its gain-bandwidth limit makes it appropriate for audio-frequency, transducer, buffer, and feedback-control circuits. Designers should account for input common-mode range, output swing, input bias current, and supply-voltage limits when setting gain and choosing bypass capacitors.

Typical uses include industrial sensor interfaces, transducer amplification, low-frequency active filters, differential analog measurements, current-monitor amplifiers, and general control loops. In each case, the quad arrangement allows one package to serve four amplifier positions while leaving the TSSOP leads easy to inspect and rework.

When laying out the circuit, place supply-bypass capacitors close to the supply pins, keep feedback traces short, and route high-impedance input nodes away from switching nodes. Confirm that the input common-mode voltage and required output swing remain inside the device operating limits. Use the manufacturer datasheet pin-description table when assigning PCB tracks and verify supply tolerance before energizing the board.

This page consolidates the manufacturer product information, distributor package details, and cross-reference findings into an engineering-focused guide. It also distinguishes the verified LM2902MT/NOPB configuration from related ordering codes and highlights the package, supply, temperature, and offset-voltage constraints that determine interchangeability.

Drop-in-Alternativen für LM2902MT/NOPB – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit LM2902MT/NOPB (gleiche Bauform und Footprint) – abweichend in Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Package, Packaging.

Texas Instruments
Amplifier Type: General Purpose Operational Amplifier
Input Offset Voltage: 2 mV (typical)
Package: 14-TSSOP
Texas Instruments
Amplifier Type: General purpose
Gain-Bandwidth Product: 1 MHz
Package: 14-TSSOP (PW)

LM2902MTX/NOPB

✅ Drop-In
Texas Instruments
📦 14-TSSOP
Quad general-purpose operational amplifier · 4 circuits · 4 independent operational amplifiers · 26 V · Single supply · 1 MHz · Internally frequency compensated · General purpose

Preis auf Anfrage

Datenblatt ansehen →

LM2902MT/NOPB Grenzwerte & elektrische Eigenschaften

Amplifier Type General-purpose operational amplifier
Number of Amplifier Sections 4 circuits
Maximum Total Supply Voltage 26 V
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 2 mV
Supply Voltage Type Single or split supply
Betriebstemperaturbereich -40°C to 85°C
Package Type 14-TSSOP
Montageart Surface mount
Anzahl der Pins 14 pins
RoHS-Status unknown
REACH Status unknown

LM2902MT/NOPB 14-tssop Pinbelegungsleitfaden

Pinbelegung für LM2902MT/NOPB (14-tssop-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für LM2902MT/NOPB im 14-tssop-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für LM2902MT/NOPB.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

LM2902MT/NOPB ist geeignet für 6 Anwendungs: Industrial Sensor Signal Conditioning, Active Filters and Signal Conditioning, Transducer Amplification, Current Monitoring and Control Loops, Audio-Frequency Preamplifier and Mixer, General Control and Feedback Systems.

🏭

Industrial Sensor Signal Conditioning

The LM2902MT/NOPB fits industrial sensor interfaces because four general-purpose amplifier sections are integrated in one 14-TSSOP package. Each section can amplify a low-level transducer signal, buffer a high-impedance source, or implement active filtering around a 1.2 MHz gain-bandwidth limit. The 2 mV input offset voltage is suitable for many measurement chains where requirements do not demand precision-offset correction. Verify bias-current error against the sensor impedance, keep the input common-mode voltage within the operating range, and place a bypass capacitor close to the supply pins.

⚡

Active Filters and Signal Conditioning

A quad operational amplifier is useful for building low-frequency active filters, where each amplifier stage can perform integration, gain, inversion, or buffering. The LM2902MT/NOPB provides a 1.2 MHz gain-bandwidth product and four independent sections in a single 14-TSSOP package, allowing a complete two-stage filter with an input buffer and output driver. Keep component tolerances low for cutoff accuracy and follow the datasheet's stability guidance near capacitive loads. Short feedback paths and grounded return routing help maintain predictable phase margin.

📡

Transducer Amplification

The LM2902MT/NOPB can amplify outputs from resistive, capacitive, or piezoelectric-style transducers when the signal bandwidth is comfortably below its 1.2 MHz gain-bandwidth capability. The quad arrangement allows one amplifier for transducer excitation or sensing, one for gain, and two for filtering and output buffering. The 26 V maximum total supply supports industrial signal levels, but common-mode and swing limits must be respected at low supply voltages. Use input protection appropriate to the transducer, and confirm that input bias current does not create unacceptable loading.

🔧

Current Monitoring and Control Loops

For low-frequency current monitoring, the LM2902MT/NOPB can amplify a shunt voltage and perform filtering, comparison support, and error amplification in one package. A practical implementation might use one section for the shunt amplifier, one for a low-pass filter, one for a difference stage, and one for actuator drive. The 1.2 MHz bandwidth is appropriate for control loops that do not require high crossover frequency, while the four-section package reduces board area. Account for offset voltage when setting the measurement resolution and protect the input against overload.

🎧

Audio-Frequency Preamplifier and Mixer

The LM2902MT/NOPB is suitable for low-level audio preamplification, summing, and output-buffering stages because it provides four general-purpose amplifier sections with a 1.2 MHz gain-bandwidth product. One section can amplify the source, another can sum or invert channels, and the remaining sections can buffer the input and output. Keep the signal path within the input common-mode range and verify output swing at the selected supply voltage. The 2 mV input offset may create a small DC error that should be considered in precision mixing or biasing layouts.

📺

General Control and Feedback Systems

The LM2902MT/NOPB fits proportional, integral, and feedback-control loops where the loop bandwidth is well below 1.2 MHz. Its four amplifier sections can implement the error amplifier, controller stage, output buffer, and auxiliary signal conditioning without using four separate packages. This can simplify PCB routing and reduce component inventory, although all sections share the same thermal environment and supply pins. Verify stability with the actual compensation network and load capacitance, and maintain adequate loop gain margin before operating near the amplifier's bandwidth limit.

What are the key specifications of LM2902MT/NOPB that engineers should know?
The LM2902MT/NOPB is a Texas Instruments quad general-purpose operational amplifier with four amplifier sections, a 26 V maximum total supply voltage, a 1.2 MHz gain-bandwidth product, and a 2 mV input offset voltage. The part is packaged in 14-TSSOP and supports operation from -40°C to 85°C. According to the Texas Instruments LM2902 product page, its low-power design targets general-purpose amplification rather than precision or high-speed signal chains. These values make the device suitable for industrial instrumentation, buffering, filtering, and low-frequency feedback-control circuits.
What is the operating voltage of LM2902MT/NOPB?
The LM2902MT/NOPB supports a maximum total supply voltage of 26 V. Texas Instruments identifies the LM2902 as a quad, 26 V operational amplifier, and the LM2902MT/NOPB ordering option appears on the manufacturer product page. The device can be used with single or split supplies, but every input common-mode and output-swing design must remain within the limits specified for the selected supply. Use the manufacturer datasheet when confirming absolute maximum ratings and operating limits for the complete design.
What is the gain-bandwidth product of LM2902MT/NOPB?
The LM2902MT/NOPB has a gain-bandwidth product of 1.2 MHz according to the Texas Instruments LM2902 product page. This bandwidth limits the practical closed-loop bandwidth as noise gain rises: a higher-gain amplifier provides less bandwidth and usually requires additional compensation or filtering. The part is therefore best suited to low-frequency and audio-frequency instrumentation rather than wideband signal processing. Check the stability and phase-margin guidance in the manufacturer datasheet before using high gain with capacitive loading.
Where can I download the LM2902MT/NOPB datasheet PDF?
The official Texas Instruments LM2902 product page at https://www.ti.com/product/LM2902 provides the manufacturer datasheet and ordering information for the LM2902 family. The LM2902MT/NOPB ordering option is listed as a 14-TSSOP device with a -40°C to 85°C temperature range. Use the datasheet from the manufacturer page for the definitive pin-description table, absolute maximum ratings, electrical characteristics, and application guidance before committing the PCB layout.
Where can I find the LM2902MT/NOPB pinout?
The LM2902MT/NOPB pinout is defined in the pin-configuration and pin-description tables of the Texas Instruments LM2902 family datasheet. The package contains 14 leads: four general-purpose amplifier sections with their associated supply pins. Because pin names and numbering must match the selected package symbol exactly, use the manufacturer pin-description table when assigning PCB tracks rather than relying on a generic quad-op-amp diagram. The verified distributor listing confirms the 14-TSSOP package for this ordering option.
Is LM2902MT/NOPB pin-compatible with LM2902MTX/NOPB?
LM2902MTX/NOPB is a closely related Texas Instruments ordering option identified in the LM2902 substitute listing, and it is the closest verified drop-in candidate for LM2902MT/NOPB. The two codes belong to the same LM2902 family and are associated with the 14-TSSOP configuration rather than different package families. Before exchanging populated boards, confirm the exact temperature grade, packing code, and orderable status on the manufacturer product page. Package equivalence does not by itself guarantee that every lifecycle or sourcing condition is identical.
What is the best drop-in replacement for LM2902MT/NOPB?
The closest confirmed drop-in candidate for LM2902MT/NOPB is LM2902MTX/NOPB from Texas Instruments. Cross-reference information groups the two LM2902 14-TSSOP ordering options together as substitutes for related LM2902 package variants. No additional candidates could be verified as both pin-to-pin compatible and housed in the identical 14-TSSOP footprint. Confirm the complete pin-description table, electrical limits, temperature range, and production status in the manufacturer datasheet before using any replacement in a new design.
Can BA2902FV-E2 replace LM2902MT/NOPB?
BA2902FV-E2 is listed as a ROHM substitute for the LM2902KDB family alongside LM2902MT/NOPB and LM2902MTX/NOPB. However, substitute-family listings do not by themselves establish an identical 14-TSSOP land pattern for this specific LM2902MT/NOPB ordering option. Compare package drawing, pin numbering, electrical characteristics, and thermal performance directly against the Texas Instruments datasheet. Do not treat the family-level cross-reference as proof of a drop-in replacement without a package-level match.
What is the best ROHM equivalent for LM2902MT/NOPB?
BA2902FV-E2 is the ROHM part identified in LM2902 substitute data as an alternative to the LM2902 family. It provides a vendor-neutral sourcing path for a similar general-purpose quad amplifier, but drop-in suitability depends on the exact package and pin layout. The verified information does not establish that BA2902FV-E2 uses the identical 14-TSSOP footprint as LM2902MT/NOPB. Request the ROHM package drawing and compare it with the Texas Instruments 14-TSSOP land pattern before treating it as a board-level replacement.
When should I choose LM2902MT/NOPB over LM2902MTX/NOPB?
Choose LM2902MT/NOPB when the tube-packed ordering code identified by the MT suffix matches your procurement and assembly process. LM2902MTX/NOPB is the related tape-and-reel ordering option in the same family, so it may be preferable for automated pick-and-place production. Electrical performance should remain equivalent within the ordering-code limits, but confirm the current orderable status, temperature grade, packing method, and quantity limits on the Texas Instruments product page. The choice is therefore driven mainly by assembly handling and supply-chain format.
Is LM2902MT/NOPB suitable for sensor signal conditioning?
The LM2902MT/NOPB is suitable for many low-frequency sensor signal-conditioning applications because it provides four general-purpose amplifiers, a 1.2 MHz gain-bandwidth product, and operation across a 26 V maximum supply. Its 2 mV input offset voltage is acceptable for moderate-accuracy measurements. Use one section as a sensor preamplifier, one as a filter, and the remaining sections for level shifting or output buffering. Verify input bias current, common-mode range, and noise performance against the sensor impedance and required measurement accuracy.
How should LM2902MT/NOPB be used with a single supply?
The LM2902MT/NOPB can be used with a single or split supply, but the input common-mode voltage must remain above the output-swing limit of the device. With a 12 V single supply, for example, a 2.5 V signal may require biasing near mid-supply before the amplifier can process it accurately. Verify the input common-mode range and output swing in the manufacturer datasheet for the actual supply voltage. Add supply-bypass capacitance at the package pins and check the output for clipping during startup and overload conditions.
Where can I buy LM2902MT/NOPB online?
Use the Request a Quote form on this page to request LM2902MT/NOPB availability, current lead time, and order confirmation. The Texas Instruments product page and distributor listings identify the part as a 14-TSSOP quad operational amplifier, while the product's sourcing status can change over time. Submit the exact MPN LM2902MT/NOPB and your required quantity so the quotation can reflect the correct tube-packed ordering code. Do not substitute a different suffix without confirming assembly format and grade requirements.
What is the price of LM2902MT/NOPB?
The current commercial terms for LM2902MT/NOPB are provided through the Request a Quote form on this page. Pricing for this ordering option can vary with quantity, packaging format, and market availability, so a dated fixed figure would quickly become inaccurate. Request a quotation using the exact MPN LM2902MT/NOPB and indicate the required annual and prototype quantities. The request can also confirm current stock, minimum order quantity, lead time, and the compatible LM2902MTX/NOPB tape-and-reel option.
What is the lead time and stock status of LM2902MT/NOPB?
Request the current lead time, minimum order quantity, and stock status for LM2902MT/NOPB through the Request a Quote form on this page. Texas Instruments lists the LM2902 family on its official product page, while distributor availability for this exact ordering code can vary independently of the family's product status. A quotation response should confirm the manufacturing schedule and the available packaging format. Because the part may require special planning, include your production schedule and requested quantity with the request.
What can replace LM2902MT/NOPB?
LM2902MTX/NOPB is the closest confirmed replacement because it is identified in the LM2902 substitute data and uses the same 14-TSSOP family configuration. BA2902FV-E2 from ROHM appears in family-level substitute listings, but its exact package and pin compatibility with this specific ordering option require direct comparison of the manufacturer drawings. For an existing PCB, verify pin numbering, supply limits, offset voltage, temperature range, and output behavior. For a new design, also compare bandwidth, bias current, and noise before selecting a substitute.

Technische Referenzdaten für LM2902MT/NOPB – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose LM2902MT/NOPB when a design needs four general-purpose amplifiers, a 26 V maximum total supply, and a 1.2 MHz gain-bandwidth product in a 14-TSSOP package. It is particularly practical for low-frequency instrumentation, transducers, filtering, and feedback control where moderate offset accuracy and low power are acceptable. Select LM2902MTX/NOPB when automated tape-and-reel assembly is preferred within the same family. Treat BA2902FV-E2 as a sourcing alternative only after comparing its package drawing, pin numbering, and electrical characteristics against the Texas Instruments device. For new precision or high-speed designs, choose an amplifier with lower offset, lower noise, wider bandwidth, or lower bias current rather than treating a general-purpose LM2902 as a universal solution.

Vergleich mit Alternativen

Parameter Dieses Produkt LM2902MTX/NOPB
Brand Texas Instruments Texas Instruments
Package 14-TSSOP 14-TSSOP
Amplifier Sections 4 4
Maximum Total Supply Voltage 26 V 26 V
Gain-Bandwidth Product 1.2 MHz 1.2 MHz
Input Offset Voltage 2 mV 2 mV
Ordering Format MT tube-packed ordering code MTX tape-and-reel ordering code

Wichtigste Unterscheidungsmerkmale

  • Four general-purpose amplifiers in one 14-TSSOP package (vs. LM2902MTX/NOPB)
  • Single-package consolidation for four amplifier positions (vs. BA2902FV-E2)
  • Industrial supply headroom for general-purpose analog design (vs. LM2902MX/NOPB)

Designhinweise

Place the supply-bypass capacitor as close as practical to the LM2902MT/NOPB supply pins, and route the return current directly to the package ground connection. Keep the four amplifier sections' feedback traces compact and separate high-impedance inputs from switching-node copper. Because the device contains four amplifiers sharing package pins, poor supply decoupling can couple noise between channels and disturb output settling.

Do not assume that a single 12 V supply permits zero-volt input signals without biasing. Check the input common-mode range and output swing in the manufacturer datasheet for the actual supply voltage, and bias the signal near mid-supply when necessary. Also verify the 26 V total supply limit, output loading, and operating temperature before power-up. These checks prevent input-stage saturation and clipping that can resemble a failed amplifier.

The 1.2 MHz gain-bandwidth product means usable closed-loop bandwidth falls as noise gain rises. Add isolation resistors when driving capacitive loads and follow the datasheet stability guidance for high-gain configurations. For instrumentation, keep the input bias-current error low by avoiding leakage paths around high-impedance sources. Place compensation and gain-setting resistors close to the amplifier pins rather than spreading them across the board.

Although the LM2902 family is a low-power general-purpose amplifier, four operating sections in one 14-TSSOP package still share the same thermal path. Estimate worst-case dissipation from the actual supply voltage, output swing, and load current before defining the board's maximum operating temperature. Provide adequate PCB copper around the package and avoid placing the device next to a major heat source when channel dissipation is continuous.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

No definitive compliance declaration was identified for the exact ordering code. Verify RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation against the current Texas Instruments product page before releasing a regulated production design.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

lm2902mt nopb LM2902MT/NOPB datasheet LM2902MT/NOPB datasheet PDF LM2902MT/NOPB pinout LM2902MT/NOPB specifications Texas Instruments LM2902MT/NOPB LM2902MT/NOPB 14-TSSOP LM2902MT/NOPB replacement LM2902MT/NOPB equivalent LM2902MT/NOPB vs LM2902MTX/NOPB LM2902MT/NOPB quad operational amplifier LM2902MT/NOPB price LM2902MT/NOPB stock LM2902MT/NOPB lead time

Verwandte Bauteile & Begriffe

Texas Instruments LM2902MT/NOPB LM2902MTX/NOPB LM2902MX/NOPB BA2902FV-E2 MC3403DR quad operational amplifier general-purpose amplifier analog amplifier signal-conditioning IC voltage feedback amplifier 14-TSSOP TSSOP package family surface-mount package 26 V maximum total supply 1.2 MHz gain-bandwidth product 2 mV input offset voltage single supply operation split supply operation input common-mode range sensor interface active filter feedback control loop industrial instrumentation
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen