LM2902MT/NOPB - Quad 26V Op Amp in 14-TSSOP | TI
MPN: LM2902MT/NOPB ✗ Cuối đờiLM2902MT/NOPB Tóm tắt
A general-purpose operational amplifier is a voltage-amplified analog building block that compares an input voltage with a feedback-derived reference voltage. The quad LM2902 combines four amplifiers in one package, reducing component count and board area in sensor, control, and signal-conditioning designs. Its four amplifiers share a common supply architecture but maintain independent differential inputs and outputs.
Key features include a 26 V maximum total supply voltage, approximately 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage as identified by Texas Instruments. The low-power architecture is suited to industrial and embedded systems operating from a single supply or split supplies. Four amplifiers in one thermal package also simplify component stocking and reduce the PCB footprint required for multiple amplifier sections.
The LM2902 family uses a low-power bipolar process and provides general-purpose amplification rather than precision or high-speed performance. Its gain-bandwidth limit makes it appropriate for audio-frequency, transducer, buffer, and feedback-control circuits. Designers should account for input common-mode range, output swing, input bias current, and supply-voltage limits when setting gain and choosing bypass capacitors.
Typical uses include industrial sensor interfaces, transducer amplification, low-frequency active filters, differential analog measurements, current-monitor amplifiers, and general control loops. In each case, the quad arrangement allows one package to serve four amplifier positions while leaving the TSSOP leads easy to inspect and rework.
When laying out the circuit, place supply-bypass capacitors close to the supply pins, keep feedback traces short, and route high-impedance input nodes away from switching nodes. Confirm that the input common-mode voltage and required output swing remain inside the device operating limits. Use the manufacturer datasheet pin-description table when assigning PCB tracks and verify supply tolerance before energizing the board.
This page consolidates the manufacturer product information, distributor package details, and cross-reference findings into an engineering-focused guide. It also distinguishes the verified LM2902MT/NOPB configuration from related ordering codes and highlights the package, supply, temperature, and offset-voltage constraints that determine interchangeability.
Bộ thay thế dễ dàng lắp đặt cho LM2902MT/NOPB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2902MT/NOPB (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Package, Packaging.
LM2902MTX/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2902MT/NOPB Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifier Sections | 4 circuits |
| Maximum Total Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Supply Voltage Type | Single or split supply |
| Khoảng nhiệt độ hoạt động | -40°C to 85°C |
| Package Type | 14-TSSOP |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 14 pins |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
Hướng dẫn cấu hình chân LM2902MT/NOPB 14-tssop
Cấu hình chân cho LM2902MT/NOPB (14-tssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2902MT/NOPB.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2902MT/NOPB phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Active Filters and Signal Conditioning, Transducer Amplification, Current Monitoring and Control Loops, Audio-Frequency Preamplifier and Mixer, General Control and Feedback Systems.
Industrial Sensor Signal Conditioning
The LM2902MT/NOPB fits industrial sensor interfaces because four general-purpose amplifier sections are integrated in one 14-TSSOP package. Each section can amplify a low-level transducer signal, buffer a high-impedance source, or implement active filtering around a 1.2 MHz gain-bandwidth limit. The 2 mV input offset voltage is suitable for many measurement chains where requirements do not demand precision-offset correction. Verify bias-current error against the sensor impedance, keep the input common-mode voltage within the operating range, and place a bypass capacitor close to the supply pins.
Được đề xuất
Active Filters and Signal Conditioning
A quad operational amplifier is useful for building low-frequency active filters, where each amplifier stage can perform integration, gain, inversion, or buffering. The LM2902MT/NOPB provides a 1.2 MHz gain-bandwidth product and four independent sections in a single 14-TSSOP package, allowing a complete two-stage filter with an input buffer and output driver. Keep component tolerances low for cutoff accuracy and follow the datasheet's stability guidance near capacitive loads. Short feedback paths and grounded return routing help maintain predictable phase margin.
Được đề xuất
Transducer Amplification
The LM2902MT/NOPB can amplify outputs from resistive, capacitive, or piezoelectric-style transducers when the signal bandwidth is comfortably below its 1.2 MHz gain-bandwidth capability. The quad arrangement allows one amplifier for transducer excitation or sensing, one for gain, and two for filtering and output buffering. The 26 V maximum total supply supports industrial signal levels, but common-mode and swing limits must be respected at low supply voltages. Use input protection appropriate to the transducer, and confirm that input bias current does not create unacceptable loading.
Được đề xuất
Current Monitoring and Control Loops
For low-frequency current monitoring, the LM2902MT/NOPB can amplify a shunt voltage and perform filtering, comparison support, and error amplification in one package. A practical implementation might use one section for the shunt amplifier, one for a low-pass filter, one for a difference stage, and one for actuator drive. The 1.2 MHz bandwidth is appropriate for control loops that do not require high crossover frequency, while the four-section package reduces board area. Account for offset voltage when setting the measurement resolution and protect the input against overload.
Được đề xuất
Audio-Frequency Preamplifier and Mixer
The LM2902MT/NOPB is suitable for low-level audio preamplification, summing, and output-buffering stages because it provides four general-purpose amplifier sections with a 1.2 MHz gain-bandwidth product. One section can amplify the source, another can sum or invert channels, and the remaining sections can buffer the input and output. Keep the signal path within the input common-mode range and verify output swing at the selected supply voltage. The 2 mV input offset may create a small DC error that should be considered in precision mixing or biasing layouts.
Được đề xuất
General Control and Feedback Systems
The LM2902MT/NOPB fits proportional, integral, and feedback-control loops where the loop bandwidth is well below 1.2 MHz. Its four amplifier sections can implement the error amplifier, controller stage, output buffer, and auxiliary signal conditioning without using four separate packages. This can simplify PCB routing and reduce component inventory, although all sections share the same thermal environment and supply pins. Verify stability with the actual compensation network and load capacitance, and maintain adequate loop gain margin before operating near the amplifier's bandwidth limit.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2902MT/NOPB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2902MTX/NOPB |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 14-TSSOP | 14-TSSOP |
| Amplifier Sections | 4 | 4 |
| Maximum Total Supply Voltage | 26 V | 26 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz |
| Input Offset Voltage | 2 mV | 2 mV |
| Ordering Format | MT tube-packed ordering code | MTX tape-and-reel ordering code |
Bảo phân biệt quan trọng
- Four general-purpose amplifiers in one 14-TSSOP package (vsLM2902MTX/NOPB)
- Single-package consolidation for four amplifier positions (vsBA2902FV-E2)
- Industrial supply headroom for general-purpose analog design (vsLM2902MX/NOPB)
Ghi chú thiết kế
Place the supply-bypass capacitor as close as practical to the LM2902MT/NOPB supply pins, and route the return current directly to the package ground connection. Keep the four amplifier sections' feedback traces compact and separate high-impedance inputs from switching-node copper. Because the device contains four amplifiers sharing package pins, poor supply decoupling can couple noise between channels and disturb output settling.
Do not assume that a single 12 V supply permits zero-volt input signals without biasing. Check the input common-mode range and output swing in the manufacturer datasheet for the actual supply voltage, and bias the signal near mid-supply when necessary. Also verify the 26 V total supply limit, output loading, and operating temperature before power-up. These checks prevent input-stage saturation and clipping that can resemble a failed amplifier.
The 1.2 MHz gain-bandwidth product means usable closed-loop bandwidth falls as noise gain rises. Add isolation resistors when driving capacitive loads and follow the datasheet stability guidance for high-gain configurations. For instrumentation, keep the input bias-current error low by avoiding leakage paths around high-impedance sources. Place compensation and gain-setting resistors close to the amplifier pins rather than spreading them across the board.
Although the LM2902 family is a low-power general-purpose amplifier, four operating sections in one 14-TSSOP package still share the same thermal path. Estimate worst-case dissipation from the actual supply voltage, output swing, and load current before defining the board's maximum operating temperature. Provide adequate PCB copper around the package and avoid placing the device next to a major heat source when channel dissipation is continuous.
Thông tin tuân thủ
No definitive compliance declaration was identified for the exact ordering code. Verify RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation against the current Texas Instruments product page before releasing a regulated production design.