LM2902MT/NOPB - Quad 26V Op Amp in 14-TSSOP | TI
MPN: LM2902MT/NOPB ✗ 停產LM2902MT/NOPB 概覽
A general-purpose operational amplifier is a voltage-amplified analog building block that compares an input voltage with a feedback-derived reference voltage. The quad LM2902 combines four amplifiers in one package, reducing component count and board area in sensor, control, and signal-conditioning designs. Its four amplifiers share a common supply architecture but maintain independent differential inputs and outputs.
Key features include a 26 V maximum total supply voltage, approximately 1.2 MHz gain-bandwidth product, and 2 mV input offset voltage as identified by Texas Instruments. The low-power architecture is suited to industrial and embedded systems operating from a single supply or split supplies. Four amplifiers in one thermal package also simplify component stocking and reduce the PCB footprint required for multiple amplifier sections.
The LM2902 family uses a low-power bipolar process and provides general-purpose amplification rather than precision or high-speed performance. Its gain-bandwidth limit makes it appropriate for audio-frequency, transducer, buffer, and feedback-control circuits. Designers should account for input common-mode range, output swing, input bias current, and supply-voltage limits when setting gain and choosing bypass capacitors.
Typical uses include industrial sensor interfaces, transducer amplification, low-frequency active filters, differential analog measurements, current-monitor amplifiers, and general control loops. In each case, the quad arrangement allows one package to serve four amplifier positions while leaving the TSSOP leads easy to inspect and rework.
When laying out the circuit, place supply-bypass capacitors close to the supply pins, keep feedback traces short, and route high-impedance input nodes away from switching nodes. Confirm that the input common-mode voltage and required output swing remain inside the device operating limits. Use the manufacturer datasheet pin-description table when assigning PCB tracks and verify supply tolerance before energizing the board.
This page consolidates the manufacturer product information, distributor package details, and cross-reference findings into an engineering-focused guide. It also distinguishes the verified LM2902MT/NOPB configuration from related ordering codes and highlights the package, supply, temperature, and offset-voltage constraints that determine interchangeability.
直接替換替代品,適用於 LM2902MT/NOPB — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2902MT/NOPB (相同外形與佔位) — 差異在於 Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Package, Packaging.
LM2902MTX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →LM2902MT/NOPB 最大額定值與電氣特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifier Sections | 4 circuits |
| Maximum Total Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Supply Voltage Type | Single or split supply |
| 工作溫度範圍 | -40°C to 85°C |
| Package Type | 14-TSSOP |
| 安裝類型 | Surface mount |
| 腳位數 | 14 pins |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
LM2902MT/NOPB 14-tssop 腳位配置指南
LM2902MT/NOPB(14-tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2902MT/NOPB.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2902MT/NOPB 適用於 6 應用s: Industrial Sensor Signal Conditioning, Active Filters and Signal Conditioning, Transducer Amplification, Current Monitoring and Control Loops, Audio-Frequency Preamplifier and Mixer, General Control and Feedback Systems.
Industrial Sensor Signal Conditioning
The LM2902MT/NOPB fits industrial sensor interfaces because four general-purpose amplifier sections are integrated in one 14-TSSOP package. Each section can amplify a low-level transducer signal, buffer a high-impedance source, or implement active filtering around a 1.2 MHz gain-bandwidth limit. The 2 mV input offset voltage is suitable for many measurement chains where requirements do not demand precision-offset correction. Verify bias-current error against the sensor impedance, keep the input common-mode voltage within the operating range, and place a bypass capacitor close to the supply pins.
推薦
Active Filters and Signal Conditioning
A quad operational amplifier is useful for building low-frequency active filters, where each amplifier stage can perform integration, gain, inversion, or buffering. The LM2902MT/NOPB provides a 1.2 MHz gain-bandwidth product and four independent sections in a single 14-TSSOP package, allowing a complete two-stage filter with an input buffer and output driver. Keep component tolerances low for cutoff accuracy and follow the datasheet's stability guidance near capacitive loads. Short feedback paths and grounded return routing help maintain predictable phase margin.
推薦
Transducer Amplification
The LM2902MT/NOPB can amplify outputs from resistive, capacitive, or piezoelectric-style transducers when the signal bandwidth is comfortably below its 1.2 MHz gain-bandwidth capability. The quad arrangement allows one amplifier for transducer excitation or sensing, one for gain, and two for filtering and output buffering. The 26 V maximum total supply supports industrial signal levels, but common-mode and swing limits must be respected at low supply voltages. Use input protection appropriate to the transducer, and confirm that input bias current does not create unacceptable loading.
推薦
Current Monitoring and Control Loops
For low-frequency current monitoring, the LM2902MT/NOPB can amplify a shunt voltage and perform filtering, comparison support, and error amplification in one package. A practical implementation might use one section for the shunt amplifier, one for a low-pass filter, one for a difference stage, and one for actuator drive. The 1.2 MHz bandwidth is appropriate for control loops that do not require high crossover frequency, while the four-section package reduces board area. Account for offset voltage when setting the measurement resolution and protect the input against overload.
推薦
Audio-Frequency Preamplifier and Mixer
The LM2902MT/NOPB is suitable for low-level audio preamplification, summing, and output-buffering stages because it provides four general-purpose amplifier sections with a 1.2 MHz gain-bandwidth product. One section can amplify the source, another can sum or invert channels, and the remaining sections can buffer the input and output. Keep the signal path within the input common-mode range and verify output swing at the selected supply voltage. The 2 mV input offset may create a small DC error that should be considered in precision mixing or biasing layouts.
推薦
General Control and Feedback Systems
The LM2902MT/NOPB fits proportional, integral, and feedback-control loops where the loop bandwidth is well below 1.2 MHz. Its four amplifier sections can implement the error amplifier, controller stage, output buffer, and auxiliary signal conditioning without using four separate packages. This can simplify PCB routing and reduce component inventory, although all sections share the same thermal environment and supply pins. Verify stability with the actual compensation network and load capacitance, and maintain adequate loop gain margin before operating near the amplifier's bandwidth limit.
推薦
推薦產品摘要
工程參考資料,適用於 LM2902MT/NOPB — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2902MTX/NOPB |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 14-TSSOP | 14-TSSOP |
| Amplifier Sections | 4 | 4 |
| Maximum Total Supply Voltage | 26 V | 26 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz |
| Input Offset Voltage | 2 mV | 2 mV |
| Ordering Format | MT tube-packed ordering code | MTX tape-and-reel ordering code |
主要差異化特點
- Four general-purpose amplifiers in one 14-TSSOP package (對比LM2902MTX/NOPB)
- Single-package consolidation for four amplifier positions (對比BA2902FV-E2)
- Industrial supply headroom for general-purpose analog design (對比LM2902MX/NOPB)
設計說明
Place the supply-bypass capacitor as close as practical to the LM2902MT/NOPB supply pins, and route the return current directly to the package ground connection. Keep the four amplifier sections' feedback traces compact and separate high-impedance inputs from switching-node copper. Because the device contains four amplifiers sharing package pins, poor supply decoupling can couple noise between channels and disturb output settling.
Do not assume that a single 12 V supply permits zero-volt input signals without biasing. Check the input common-mode range and output swing in the manufacturer datasheet for the actual supply voltage, and bias the signal near mid-supply when necessary. Also verify the 26 V total supply limit, output loading, and operating temperature before power-up. These checks prevent input-stage saturation and clipping that can resemble a failed amplifier.
The 1.2 MHz gain-bandwidth product means usable closed-loop bandwidth falls as noise gain rises. Add isolation resistors when driving capacitive loads and follow the datasheet stability guidance for high-gain configurations. For instrumentation, keep the input bias-current error low by avoiding leakage paths around high-impedance sources. Place compensation and gain-setting resistors close to the amplifier pins rather than spreading them across the board.
Although the LM2902 family is a low-power general-purpose amplifier, four operating sections in one 14-TSSOP package still share the same thermal path. Estimate worst-case dissipation from the actual supply voltage, output swing, and load current before defining the board's maximum operating temperature. Provide adequate PCB copper around the package and avoid placing the device next to a major heat source when channel dissipation is continuous.
合規資訊
No definitive compliance declaration was identified for the exact ordering code. Verify RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation against the current Texas Instruments product page before releasing a regulated production design.