LM2904AVQDRG4Q1 - 26V Dual 700kHz Op Amp | Texas Instruments
Teilenummer: LM2904AVQDRG4Q1 ✓ AktivLM2904AVQDRG4Q1 Übersicht
An operational amplifier is a high-gain, differential-input analog amplifier that uses external feedback to set its closed-loop gain and signal behavior. Within the broader semiconductor hierarchy, this device belongs to the linear-amplifier family and ultimately to the amplifier-IC category. The LM2904 family is widely used for low-frequency signal conditioning because it combines reasonably high open-loop gain, broad supply-voltage capability, low supply-current consumption, and a conventional industry-standard pin arrangement.
The most prominent operating characteristics are its 26 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate. Each channel supports single-supply operation, while the two amplifiers can also be used with suitable bipolar supplies. The device is intended for general-purpose amplification and includes two circuits in one 8-SOIC package, reducing board area compared with separate single amplifiers.
Its frequency-compensated architecture is suited to non-inverting, inverting, summing, comparator-like, and transducer-amplification stages operating within the device's bandwidth. The automotive qualification is important where operating-temperature robustness and controlled quality are required. Exact input-offset voltage, input-bias current, output-current capability, common-mode limits, and temperature limits must be confirmed in the manufacturer datasheet for the selected grade and package.
Typical uses include low-level sensor conditioning, transducer amplifiers, DC gain stages, active filters, audio and communications interfaces, and automotive signal-processing modules. The two-amplifier configuration is particularly useful when a board needs two similar signal paths in one package, such as differential sensing or paired filter stages.
Design with the 700 kHz bandwidth and 0.3 V/µs slew rate in mind. Keep input and feedback routing short, observe the supply and common-mode limits from the manufacturer datasheet, and verify output swing at the intended load. Decoupling capacitors should be placed close to the supply pins to reduce supply impedance and switching noise.
This product page combines the exact ordering information, package details, qualified family information, verified drop-in candidates, and practical design considerations needed to plan an automotive dual-op-amp design before committing the LM2904AVQDRG4Q1 to a PCB.
Drop-in-Alternativen für LM2904AVQDRG4Q1 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit LM2904AVQDRG4Q1 (gleiche Bauform und Footprint) – abweichend in Package, Amplifier Type, Number of Channels, Operating Temperature Range, Slew Rate.
LM2904-Q1
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LM2904DR
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LM2904BIDR
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LM2904BA
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
LM2904M/NOPB
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →LM2904AVQDRG4Q1 Grenzwerte & elektrische Eigenschaften
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 2 circuits |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Architecture | Frequency-compensated dual amplifier |
| Automotive Qualification | AEC-Q100 qualified |
| Gehäuse | 8-SOIC, 0.154 in body width |
| Package Width | 3.90 mm |
| Packaging | Tape & Reel |
| Operating Supply | Single supply or dual supply |
| Versorgungsstrom | 0.7 mA typical per amplifier |
LM2904AVQDRG4Q1 Pin-Konfiguration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN1- — Amplifier 1 inverting input |
| Pin 3 | IN1+ — Amplifier 1 noninverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | IN2+ — Amplifier 2 noninverting input |
| Pin 6 | IN2- — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | V+ — Positive supply connection |
Typische Anwendungen
LM2904AVQDRG4Q1 ist geeignet für 6 Anwendungs: Automotive Sensor Signal Conditioning, Transducer Amplifier, Active Audio Filtering, Industrial DC Gain Stage, Battery-Powered Monitoring, Communications Interface Amplifier.
Automotive Sensor Signal Conditioning
The LM2904AVQDRG4Q1 fits low-level automotive sensor conditioning because its two frequency-compensated channels can amplify and filter related signals within the 700 kHz bandwidth limit. Its 0.3 V/µs slew rate supports signals with moderate frequency content, while the 26 V supply rating accommodates automotive transient-protected rails. One channel can amplify the transducer and the other can form a filter or active gain stage. Because this is an AEC-Q100-qualified family member, engineers can use it in body, chassis, powertrain, or body-electronics modules after confirming operating-temperature range, common-mode limits, and output-swing requirements in the manufacturer datasheet.
Empfohlen
Transducer Amplifier
The LM2904AVQDRG4Q1 is suitable for a general-purpose transducer-amplifier stage when sensor bandwidth and output amplitude remain within its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate. The two channels allow a compact implementation with one channel providing signal gain and the second supporting filtering or offset correction. Low supply-current consumption of 0.7 mA typical per amplifier is useful in power-constrained circuits. Before selecting the device for a high-impedance sensor, verify input-bias-current and input-offset-voltage limits, because those values determine input-error contribution and whether an external bias or instrumentation stage is required.
Empfohlen
Active Audio Filtering
The LM2904AVQDRG4Q1 can implement active filtering or gain-control stages in low-frequency audio and communications equipment when the desired signal bandwidth is comfortably below 700 kHz. Its 0.3 V/µs slew rate limits large-signal performance, so designers should calculate the maximum amplitude and frequency of the output waveform before relying on full output swing. The dual package also reduces board area by placing two linked filter or gain stages in one 8-SOIC footprint. The manufacturer datasheet should be consulted for output-current capability, load stability, noise, and output-swing boundaries before driving speaker, line, or higher-capacitance loads.
Empfohlen
Industrial DC Gain Stage
The LM2904AVQDRG4Q1 supports non-inverting and inverting DC gain stages where the closed-loop bandwidth remains compatible with the 700 kHz gain-bandwidth product. A two-amplifier arrangement can implement gain followed by active filtering without requiring two separate packages. The 26 V rating provides headroom for protected industrial supply rails, although input common-mode and output-swing constraints still define the usable signal range. Use short feedback paths, maintain stable resistor values, and place supply-bypass capacitance close to pin 8 and the ground reference at pin 4 to limit parasitic feedback and improve transient behavior.
Empfohlen
Battery-Powered Monitoring
The LM2904AVQDRG4Q1 is suitable for battery-powered monitoring electronics where low supply-current consumption is important. The device draws 0.7 mA typical per amplifier and supports single-supply operation, allowing two low-power signal-conditioning channels in one 8-SOIC package. A monitoring system could use one channel to amplify a sensor output and the other to amplify a reference or battery-divider signal. Designers should confirm the minimum operating supply, common-mode input range, and output-swing limits for the selected automotive suffix, because those constraints determine whether measurements remain accurate near the bottom of the supply range.
Empfohlen
Communications Interface Amplifier
The LM2904AVQDRG4Q1 can serve as a general-purpose communications-interface amplifier for low- and moderate-frequency baseband stages. Its 700 kHz gain-bandwidth product is appropriate for slower control or measurement paths rather than high-speed data lines, while the 0.3 V/µs slew rate helps preserve large-signal behavior within that band. The dual-channel package supports a transmit or receive gain path plus buffering. Layout should minimize loop area around the high-impedance inputs and feedback components, and supply decoupling should be placed close to the device to prevent supply ripple from modulating the communication signal.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für LM2904AVQDRG4Q1 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | LM2904-Q1 | LM2904 | LM2904B | LM2904BA | LM2904M/NOPB |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
Wichtigste Unterscheidungsmerkmale
- Automotive qualification is retained in the exact ordering family (vs. LM2904)
- Higher-bandwidth upgrade is available without changing the 8-SOIC footprint (vs. LM2904B)
- Two signal-processing channels share one package (vs. LM2904M/NOPB)
Designhinweise
Place the positive-supply bypass capacitor immediately between pin 8 and the ground reference associated with pin 4, with the shortest and lowest-inductance path possible. If the two channels operate at different frequencies or analog levels, evaluate separate local bypass paths to prevent one channel's transient current from disturbing the other. Keep the input and feedback components close to their corresponding pins to minimize parasitic capacitance, which can alter closed-loop stability at high loop gain.
The two amplifier channels share an 8-SOIC package but have separate inputs and outputs; pin 4 is the negative supply or ground reference, while pin 8 is the positive supply. Route sensitive input nodes away from supply traces, clock edges, inductors, and switching-node copper. Maintain a quiet return path for each amplifier so output current and input bias current do not share a high-impedance ground segment.
Do not treat the 26 V rating as permission to place any signal directly on the supply pins. Verify input common-mode range, output swing, minimum supply voltage, input offset, bias current, and capacitive-load stability in the manufacturer datasheet. For a drop-in redesign, preserve the complete orderable suffix because LM2904, LM2904-Q1, LM2904B, and LM2904BA can differ in qualification, bandwidth, supply rating, or grade-specific limits even when their pin arrangement remains compatible.
Compliance-Informationen
The LM2904-Q1 family is identified as qualified to AEC-Q100 specifications for automotive applications. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not established for the exact ordering code in the cited material.