MAX232CASE+T - 5V 2Tx/2Rx RS-232 Transceiver | Analog Devices
Teilenummer: MAX232CASE+T ✓ AktivMAX232CASE+T Übersicht
An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between digital logic and serial communications. A transmitter converts TTL or CMOS data into bipolar RS-232 levels, while a receiver converts bipolar RS-232 signals back into logic-compatible levels. In the broader semiconductor hierarchy, the MAX232 belongs to interface ICs, then transceiver ICs, then RS-232 line drivers and receivers.
Key characteristics include two RS-232 transmitters, two RS-232 receivers, operation from a single +5 V supply, and a 16-SOIC footprint. The MAX232 family is intended for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly where positive and negative RS-232 voltage rails are not otherwise available. This makes it suitable for legacy serial ports, service interfaces, industrial controllers, and embedded debug links.
The device uses charge-pump circuitry to generate the negative RS-232 voltage required by the transmitters. Charge pumps, external capacitors, receiver inputs, and transmit outputs therefore form one signal-path subsystem; component placement and trace routing determine whether the interface meets the timing and noise expectations of the connected equipment. The receiver section converts bipolar input signals into a single-ended logic output for the host controller.
Typical uses include point-to-point RS-232 links between a microcontroller and a peripheral, service-console connections in industrial equipment, legacy printer or instrument interfaces, and isolated debugging ports. The two-transmitter, two-receiver arrangement supports one hardware flow-control pair alongside the primary data pair when the connected equipment uses RTS and CTS signaling.
For a new layout, follow the manufacturer datasheet for capacitor selection, charge-pump placement, and driver-output routing. Place the required charge-pump capacitors close to their associated pins, keep RS-232 driver traces away from sensitive logic and clock nets, and confirm that the equipment-side ground and shield strategy matches the target system.
This page adds practical replacement guidance, package-level comparison, application-specific design guidance, and engineering-focused FAQ answers that complement the manufacturer datasheet. It also identifies where a pin-compatible substitution must be checked for temperature grade, supply requirements, and channel-level functional differences before an existing layout is reused.
Drop-in-Alternativen für MAX232CASE+T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX232CASE+T (gleiche Bauform und Footprint) – abweichend in Package, Interface Standard, Product Type, RoHS Status, Supply Voltage.
MAX232CSE+T
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX232ACSE+T
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX232EESE+
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →MAX232ESE+
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →MAX232CUI+T
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX232CASE+T Technische Daten
| Product Type | RS-232 transceiver |
| Versorgungsspannung | +5 V |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Interface Standard | RS-232 / EIA-TIA-232E / V.28 / V.24 |
| Logic Compatibility | TTL / CMOS |
| Betriebstemperaturbereich | -40 C to +125 C |
| Gehäuse | 16-SOIC |
| Anzahl der Pins | 16 pins |
| Montageart | Surface mount |
| Automotive Qualification | Not specified |
| RoHS-Status | Unknown |
| REACH Status | Unknown |
| Lead-Free Status | Unknown |
| Halogen-Free Status | Unknown |
| Charge-Pump Capacitors | External capacitors required |
| Output Polarity | Bipolar RS-232 |
| Data Direction | 2 transmit and 2 receive channels |
MAX232CASE+T Pin-Konfiguration
| Pin 1 | V+ — Positive charge-pump output |
| Pin 2 | R1OUT — Receiver 1 output |
| Pin 3 | R2OUT — Receiver 2 output |
| Pin 4 | R2IN — Receiver 2 input |
| Pin 5 | R1IN — Receiver 1 input |
| Pin 6 | GND — Ground |
| Pin 7 | T1OUT — Transmitter 1 output |
| Pin 8 | T2OUT — Transmitter 2 output |
| Pin 9 | T2IN — Transmitter 2 input |
| Pin 10 | T1IN — Transmitter 1 input |
| Pin 11 | V- — Negative charge-pump output |
| Pin 12 | NC — Not connected |
| Pin 13 | NC — Not connected |
| Pin 14 | NC — Not connected |
| Pin 15 | NC — Not connected |
| Pin 16 | VCC — Positive supply voltage input |
Typische Anwendungen
MAX232CASE+T ist geeignet für 6 Anwendungs: Microcontroller RS-232 Serial Port, Industrial Equipment Service Console, FPGA Debug and Configuration Link, Legacy Printer and Instrument Interface, Point-to-Point Communications Link, Telecom and Network Appliance Management.
Microcontroller RS-232 Serial Port
The MAX232CASE+T is suitable when a microcontroller UART must connect to a conventional RS-232 port. Its two transmitters convert TTL/CMOS TX signals into bipolar RS-232 levels, while its two receivers return the remote port's logic-compatible data and flow-control signals. Operating from +5 V and providing two transmit and two receive channels also leaves room for RTS and CTS handshaking on the second channel pair. The 16-SOIC package keeps the interface compact, while the -40 C to +125 C operating range supports industrial equipment. Use the manufacturer application circuit for the charge-pump capacitor values and connect the logic ground to the interface ground according to the system grounding strategy.
Empfohlen
Industrial Equipment Service Console
An industrial controller or instrument can use the MAX232CASE+T to provide a legacy service and configuration port. The two transmitters and two receivers support both the primary serial channel and a second pair that is often assigned to hardware flow control. The +5 V supply matches many legacy controller boards, and the 16-SOIC package simplifies assembly compared with a discrete transistor and charge-pump implementation. The -40 C to +125 C specification is useful in factory equipment, test systems, and network appliances where temperature excursions occur. Place the charge-pump capacitors and protection components close to the transceiver, and keep the bipolar RS-232 traces separated from sensitive analog and high-speed digital nets.
Empfohlen
FPGA Debug and Configuration Link
The MAX232CASE+T can provide a simple wired debug link between an FPGA board and a legacy PC serial port. Two RS-232 transmitters move command and status data toward the host, while two receivers accept data and acknowledgments from the host. This arrangement is particularly convenient when the FPGA does not include a USB-to-serial bridge and the system already provides a 5 V rail. The 16-SOIC package reduces board-area requirements, and the extended -40 C to +125 C range supports industrial or laboratory instruments. For reliable operation, follow the datasheet charge-pump layout, provide the specified capacitors, and terminate or bias unused receiver inputs according to the recommended interface circuit.
Empfohlen
Legacy Printer and Instrument Interface
The MAX232CASE+T is useful for connecting a modern controller to legacy peripherals that use a DB9-style RS-232 port. It translates the controller's TTL/CMOS UART signals into the bipolar voltage swings required by older RS-232 equipment, without requiring separate +12 V and -12 V supplies. Two channels allow data to flow in both directions, and the second pair can be used if the legacy device supports hardware flow control. The device is also appropriate for laboratory instruments, barcode equipment, and service adapters that retain a +5 V supply architecture. Confirm the peripheral's logic levels, connector pinout, and cable grounding before energizing the interface, and include suitable protection against externally applied RS-232 voltage.
Empfohlen
Point-to-Point Communications Link
The MAX232CASE+T supports short point-to-point RS-232 links between two systems that use compatible serial framing. One transmitter and one receiver form the primary communication path, while the second pair can carry a status, interrupt, or hardware flow-control signal. Because the transceiver generates the required bipolar levels from a single +5 V rail, it simplifies equipment that cannot provide the dual positive and negative supplies associated with older RS-232 designs. The 16-SOIC footprint allows reuse of existing transceiver layouts. Confirm maximum data rate, propagation delay, and receiver thresholds in the datasheet, and route the RS-232 traces away from clocks, crystal circuits, and precision analog inputs to reduce coupling.
Empfohlen
Telecom and Network Appliance Management
Network appliances, routers, and telecommunications equipment can use the MAX232CASE+T for an RS-232 management or diagnostics connector. Two transmitters and two receivers accommodate a command channel and hardware handshaking, while the +5 V supply integrates easily with equipment built around a 5 V logic rail. The extended -40 C to +125 C range allows use in climate-controlled network and telecom environments with elevated internal temperatures. Designers should follow the datasheet's charge-pump capacitor arrangement, keep the transmitter outputs away from sensitive receive circuitry, and evaluate connector-level protection according to the maximum externally applied voltage. A MAX3232-family device may be preferred when lower-voltage operation or additional channel flexibility is required.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX232CASE+T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX232CSE+T | MAX232ACSE+T | MAX232EESE+ | MAX232ESE+ | MAX232CUI+T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Transmitters | 2 | 2 | 2 | 2 | 2 | 2 |
| Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| External Charge-Pump Capacitors | Required | Required | Required | Required | Required | Required |
Wichtigste Unterscheidungsmerkmale
- Extended-temperature operation (vs. MAX232ESE+)
- Automotive-qualified same-family option (vs. MAX232CSE+T)
- Established MAX232 pin and application ecosystem (vs. MAX3232ECPWR)
Designhinweise
Place the manufacturer-recommended charge-pump capacitors close to their associated IC pins and minimize the loop area of each charge-pump connection. Keep the V+ and V- capacitor return paths short and free of test-point gaps or unnecessary vias. Use the datasheet application diagram as the layout baseline, especially when the serial link must operate reliably beside switching regulators, processors, or high-speed digital circuits.
Route RS-232 transmitter outputs as short traces directly toward the connector and keep them away from crystal, reference, ADC, and high-speed clock nets. Receiver inputs are comparatively sensitive to external noise, so avoid long parallel runs beside switching nodes. Maintain a consistent reference ground between the logic system and the cable shield, and check unused receiver inputs using the recommended circuit rather than leaving them floating without guidance.
Do not assume that every 16-SOIC RS-232 transceiver is interchangeable. Confirm the supply voltage, transmitter and receiver pin positions, charge-pump capacitor values, logic thresholds, temperature grade, and qualification before using a substitute in an existing PCB. The MAX232CASE+T is specified for +5 V operation; a 3.3 V system requires a different device or a properly designed level-shifting interface.
Compliance-Informationen
The Analog Devices MAX232 product page identifies the MAX232 family as a production product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code and current manufacturer documentation.