Texas Instruments

MAX3221EIDBG4 - Single-Channel 3V RS-232 Transceiver | Texas Instruments

Teilenummer: MAX3221EIDBG4 ✗ Abgekündigt
3 V to 5.5 V Vdss 16-pin SSOP, 5.30 mm body width Package
MOQ: 1 |

MAX3221EIDBG4 Übersicht

Texas Instruments MAX3221EIDBG4 is a single-channel RS-232 line transceiver with one driver and one receiver, a 3 V to 5.5 V supply range, and operation up to 250 kbps. The device is housed in a 16-pin SSOP package. Its serial-port pins provide ±15 kV ESD protection, and the circuit includes a dual charge-pump supply for compliant RS-232 signal levels.

An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a serial connector. The transmitter converts TTL or CMOS logic into bipolar RS-232 levels, while the receiver converts the bipolar signal back into logic-compatible levels. The MAX3221 therefore connects an asynchronous communication controller to a serial port without requiring external RS-232 line drivers or receivers.

The MAX3221EIDBG4 offers a flexible 3 V to 5.5 V operating supply and a maximum signaling rate of 250 kbps. According to the manufacturer datasheet, the device meets TIA/EIA-232-F requirements and incorporates a dual charge-pump circuit. Dedicated receiver enable support allows the receiver to be controlled when the serial interface is not active.

The E and I ordering designations identify the industrial-temperature version in the SSOP package family, while G4 identifies the tape-and-reel shipping format. The 16-pin SSOP has a stated body width of approximately 5.30 mm and a package width of 0.209 inch. Lead-free status and industrial temperature grade are explicitly listed for this device.

Typical uses include industrial serial adapters, point-to-point RS-232 links, embedded data acquisition equipment, maintenance interfaces, and legacy peripheral connections. A single transceiver is appropriate when only one RS-232 channel is needed. Multiport systems generally require additional transceiver channels or a multi-channel interface IC.

PCB design should keep charge-pump capacitors and RS-232 connector protection close to the relevant pins. Confirm the complete pin assignment, exposed supply requirements, and recommended capacitor values in the manufacturer datasheet before releasing a layout. External transient protection may still be required when the connector is exposed to severe industrial surge environments.

This product page combines the device specifications, package information, application guidance, lifecycle information, and verified cross-reference findings for faster engineering review. It also highlights the limitation that no independently verified, same-package drop-in alternatives could be confirmed without risking an incorrect PCB substitution.

Drop-in-Alternativen für MAX3221EIDBG4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MAX3221CAE

✅ Drop-In
📦 16-SSOP
Same 16-SSOP format, 1-driver and 1-receiver configuration, and 3 V to 5.5 V supply; quantified supply-range and channel-count differences are 0 V and 0 channels

📋 Referenzalternative (nicht im Katalog)

MAX3221EIDBG4 Technische Daten

Device Type RS-232 line transceiver
Number of Drivers 1 driver
Number of Receivers 1 receiver
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
Communication Standard TIA/EIA-232-F
RS-232 Pin ESD Protection ±15 kV
Human Body Model ESD Protection ±15 kV
IEC 61000-4-2 Contact Discharge ±8 kV
IEC 61000-4-2 Air-Gap Discharge ±15 kV
Gehäuse 16-pin SSOP, 5.30 mm body width
Package Width 0.209 inch
Montageart Surface mount
Terminal Count 16 terminals
Temperature Grade Industrial
Lead-Free Status Lead free
Shipping Format Tape and reel
Charge-Pump Supply Dual charge-pump circuit
Receiver Enable Dedicated receiver enable pin

MAX3221EIDBG4 0.209 inch Pinbelegungsleitfaden

Pinbelegung für MAX3221EIDBG4 (0.209 inch-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MAX3221EIDBG4 im 0.209 inch-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MAX3221EIDBG4.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MAX3221EIDBG4 ist geeignet für 6 Anwendungs: Industrial Serial Port Interface, Embedded Data Acquisition Equipment, Legacy Peripheral Connectivity, Field Service and Diagnostics, Security and Access Control Equipment, Instrumentation and Test Equipment.

🏭

Industrial Serial Port Interface

The MAX3221EIDBG4 fits point-to-point RS-232 links in industrial equipment because it combines one transmitter and one receiver with a 3 V to 5.5 V supply range and a 250 kbps maximum data rate. Place it between a 3.3 V or 5 V asynchronous controller and an external DB9 or equivalent connector. The listed ±15 kV RS-232-pin ESD protection improves robustness at the interface boundary, while the industrial temperature grade supports equipment operating outside typical consumer environments.

📡

Embedded Data Acquisition Equipment

The MAX3221EIDBG4 can connect a data-acquisition controller to an RS-232 service port while operating from the same 3 V to 5.5 V range as many embedded processors. A 250 kbps data rate is suitable for configuration commands, status packets, and periodic measurements rather than continuous high-bandwidth transfer. Use the dedicated receiver-enable function to control bus participation, and follow the manufacturer charge-pump capacitor recommendations closely to maintain stable signal generation.

🖨️

Legacy Peripheral Connectivity

The MAX3221EIDBG4 is useful when maintaining equipment that relies on a single RS-232 port for a printer, controller, test fixture, or legacy peripheral. Its one-driver and one-receiver arrangement matches point-to-point serial links and reduces board area compared with a multi-channel interface. The 16-pin SSOP package supports compact designs, but engineers should verify the package drawing, pin numbering, and charge-pump capacitor network against the manufacturer datasheet before reusing an existing footprint.

🔧

Field Service and Diagnostics

The MAX3221EIDBG4 supports field-service and diagnostic ports that need a short-range wired connection between equipment and a maintenance computer. Its 250 kbps maximum rate accommodates command exchange and diagnostic output, while the specified IEC 61000-4-2 air-gap and contact discharge levels add protection at connector-facing pins. System designers should still evaluate cable length, common-mode grounding, connector shielding, and external surge protection according to the installation environment.

🛡️

Security and Access Control Equipment

The MAX3221EIDBG4 can provide a wired diagnostic or configuration channel in access-control and security equipment where a single RS-232 link replaces a disposable connector arrangement. The 3 V to 5.5 V supply compatibility supports embedded logic rails, and the listed ±15 kV ESD protection is relevant when the serial connector is accessible to personnel. Keep the interface away from unprotected antenna structures and use appropriate enclosure, filtering, and grounding controls.

📟

Instrumentation and Test Equipment

The MAX3221EIDBG4 is suitable for simple RS-232 control and telemetry interfaces in laboratory or field instrumentation. One channel is enough for a host-to-instrument command link with limited return data, and the 250 kbps rate supports configuration and status traffic. The device's industrial temperature grade and specified ESD levels are useful in controlled equipment environments. For bench-top instruments exposed to frequent connector handling, add appropriate external protection and follow the manufacturer's application circuit.

Zusammenfassung der empfohlenen Produkte

MAX3221CAE Related single-channel RS-232 transceiver; verify package before use Verwendet in: Industrial Serial Port Interface, Embedded Data Acquisition Equipment, Legacy Peripheral Connectivity, Field Service and Diagnostics, Security and Access Control Equipment, Instrumentation and Test Equipment
What is the MAX3221EIDBG4?
The MAX3221EIDBG4 is a single-channel RS-232 transceiver containing one line driver and one receiver. It operates from a 3 V to 5.5 V supply, supports data rates up to 250 kbps, and is packaged in a 16-pin SSOP. According to the Texas Instruments datasheet, it meets TIA/EIA-232-F requirements and uses a dual charge-pump circuit to generate the bipolar voltage needed by RS-232.
What are the key specifications of MAX3221EIDBG4?
The MAX3221EIDBG4 provides one RS-232 driver, one receiver, a 3 V to 5.5 V supply range, and a maximum data rate of 250 kbps. The 16-pin SSOP package also carries ±15 kV ESD protection on the RS-232 pins. According to the manufacturer datasheet, the circuit meets TIA/EIA-232-F and includes a dual charge-pump supply plus a dedicated receiver-enable input.
What is the operating voltage of MAX3221EIDBG4?
The MAX3221EIDBG4 operates from 3 V to 5.5 V. This range allows the interface to work with both 3.3 V and 5 V host systems. The Texas Instruments datasheet identifies the device as a 3 V to 5.5 V single-channel RS-232 line driver and receiver, while the product listing identifies the industrial-temperature 16-pin SSOP version.
Where can I download the MAX3221EIDBG4 datasheet PDF?
The MAX3221EIDBG4 datasheet PDF is available from the official Texas Instruments product link at https://www.ti.com/lit/ds/symlink/max3221.pdf. It contains the electrical characteristics, RS-232 timing information, charge-pump circuit, pin descriptions, and application details. Use the pin-description table and recommended circuit shown there when assigning PCB connections and selecting external capacitors.
Where can I find the MAX3221EIDBG4 pinout?
The MAX3221EIDBG4 pin assignment is published in the pin-description section of the Texas Instruments MAX3221 manufacturer datasheet. The component uses a 16-pin SSOP and includes pins for the single driver, single receiver, receiver enable, supply, ground, charge-pump capacitors, and RS-232 signal terminals. Assign every physical pin by consulting that table rather than inferring connections from a generic RS-232 schematic.
How much ESD protection does MAX3221EIDBG4 provide?
The MAX3221EIDBG4 provides ±15 kV ESD protection on the RS-232 pins. The listed protection levels include ±15 kV for the Human Body Model, ±8 kV for IEC 61000-4-2 contact discharge, and ±15 kV for IEC 61000-4-2 air-gap discharge. These ratings describe the device's built-in protection and should not be treated as a substitute for external surge protection.
Is MAX3221EIDBG4 suitable for industrial equipment?
The MAX3221EIDBG4 is identified as an industrial-temperature-grade RS-232 interface IC in a 16-pin surface-mount SSOP. Its 3 V to 5.5 V supply range, 250 kbps maximum data rate, and specified ESD protection make it appropriate for industrial serial links. Final suitability still depends on the enclosure, connector exposure, grounding, and system-level surge requirements.
What is the lifecycle status of MAX3221EIDBG4?
The MAX3221EIDBG4 is listed as obsolete and no longer manufactured. Texas Instruments continues to provide the MAX3221 family datasheet for technical reference. For a new production design, request current availability and lifecycle confirmation through the Request a Quote form on this page or select an interface device that the manufacturer currently lists as active.
Where can I buy MAX3221EIDBG4?
Use the Request a Quote form on this page to request the current price, stock position, minimum order quantity, and lead time for the MAX3221EIDBG4. Because this exact device is listed as obsolete, availability may be limited and constrained by remaining inventory. The manufacturer status and request-for-quote workflow should be considered together before committing the part to a new design.
What is the price of MAX3221EIDBG4?
The current commercial terms for the MAX3221EIDBG4 are available through the Request a Quote form on this page. The part is listed as obsolete, so quantity, condition, and remaining inventory can materially affect the offer. Use that form for a current quotation rather than relying on a historical or family-level price, and include the required package and reel quantity in the request.
What is the lead time for MAX3221EIDBG4?
The current lead time for the MAX3221EIDBG4 should be requested through the Request a Quote form on this page. Because the exact ordering code is listed as obsolete, production and allocation status must be confirmed for the requested quantity. The 16-pin SSOP package and tape-and-reel G4 shipping format should be included in the quote request to avoid an incorrect variant.
Is MAX3221EIDBG4 in stock?
Current stock for the MAX3221EIDBG4 is not fixed because the device is listed as obsolete. Request an inventory confirmation through the Request a Quote form on this page, stating the required quantity and whether the tape-and-reel format is acceptable. For a new production build, treat an available remnant as limited inventory rather than as a guaranteed long-term supply.
What can replace MAX3221EIDBG4?
The safest replacement must have the same 16-pin SSOP footprint, compatible pin assignment, compatible 3 V to 5.5 V operation, and equivalent RS-232 performance. No independently verified same-package drop-in replacement could be confirmed for the exact MAX3221EIDBG4 ordering code. Use the Request a Quote form for sourcing help, and require the replacement manufacturer to confirm pin compatibility before substituting it into an existing layout.
What is the best MAX3221EIDBG4 equivalent?
No best equivalent can be declared without verifying the exact package and pinout. The MAX3221CAE is a related single-channel RS-232 device, but package differences can prevent a direct PCB substitution. Confirm footprint, pin mapping, charge-pump capacitor values, enable logic, and data-rate limits for the proposed part. For obsolete-production continuity, submit the target MPN through the Request a Quote form.
MAX3221EIDBG4 vs MAX3221CAE - which is better for a new design?
MAX3221EIDBG4 is the obsolete 16-pin SSOP ordering code, while MAX3221CAE is a related MAX3221-family option listed in cross-reference results. Neither should be selected solely from the family relationship because package, temperature, ordering code, and lifecycle requirements must match. For a new design, compare the manufacturer datasheets and confirm current lifecycle status before choosing either device.
When should I choose MAX3221EIDBG4 instead of another RS-232 interface?
Choose the MAX3221EIDBG4 only when the existing design specifically requires its 16-pin SSOP footprint, one driver and one receiver, 3 V to 5.5 V operation, and up to 250 kbps signaling. The device is listed as obsolete, so it is more appropriate for maintaining an existing installation than for a new production platform. For new designs, prioritize a currently supported interface with the required channel count and package.

Technische Referenzdaten für MAX3221EIDBG4 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the MAX3221EIDBG4 when maintaining an existing 16-pin SSOP design that specifically requires one RS-232 driver, one receiver, a 3 V to 5.5 V supply, and operation up to 250 kbps. Its listed ±15 kV ESD protection and industrial temperature grade make it relevant for industrial and service equipment. However, the exact ordering code is obsolete, so it is generally less attractive for a new production release than a currently supported device. Do not treat a related MAX3221-family MPN as interchangeable without checking package dimensions, pinout, temperature grade, enable behavior, and charge-pump capacitor values. When footprint continuity is mandatory, preserve the original SSOP layout and validate the proposed substitute against the manufacturer datasheet. For a new design, select an active interface with the required channel count, supply range, data rate, package, and protection level.

Vergleich mit Alternativen

Parameter Dieses Produkt
Device Type Single-channel RS-232 transceiver
Number of Drivers 1
Number of Receivers 1
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
Package 16-pin SSOP
Brand Texas Instruments
RS-232 Pin ESD Protection ±15 kV
Temperature Grade Industrial
Lifecycle Status Obsolete

Wichtigste Unterscheidungsmerkmale

  • Compact single-channel RS-232 interface (vs. Multi-channel RS-232 interface)
  • Wide logic-side supply compatibility (vs. 5 V-only RS-232 interface)
  • Built-in connector-side ESD protection (vs. RS-232 transceiver without enhanced ESD)
  • Adequate signaling rate for control links (vs. Low-rate RS-232 transceiver)

Designhinweise

Place the charge-pump capacitors and the required RS-232 connector protection components close to their associated device pins. Keep the driver output and receiver input traces away from switching nodes and high-current paths to limit capacitive coupling. Use the manufacturer application circuit as the layout reference because trace length, ground placement, and capacitor return paths affect charge-pump stability and the integrity of the bipolar RS-232 waveform.

Do not substitute an electrically similar MAX3221-family device without checking the physical package and every pin assignment. A related ordering code may use a different package, temperature grade, enable configuration, or capacitor arrangement. For this obsolete ordering code, request lifecycle confirmation through the Request a Quote form and preserve the original manufacturer footprint when maintaining an existing PCB.

Keep the RS-232 connector interface physically separated from sensitive analog sections, clocks, and switching regulators. Connect the interface ground according to the system grounding strategy, and use a short return path for connector currents. The device's built-in ESD ratings protect specified pins, but external protection and cable design may still be necessary when the port experiences severe surges or long exposed cable runs.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Yes
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The part is identified as lead free. RoHS, REACH, halogen-free, and conflict-minerals status are not established by the available product information.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MAX3221EIDBG4 datasheet MAX3221EIDBG4 datasheet pdf MAX3221EIDBG4 pinout MAX3221EIDBG4 specifications MAX3221EIDBG4 equivalent MAX3221EIDBG4 replacement MAX3221EIDBG4 cross reference MAX3221EIDBG4 footprint Texas Instruments MAX3221EIDBG4 MAX3221EIDBG4 RS-232 transceiver MAX3221EIDBG4 16-SSOP MAX3221EIDBG4 industrial interface MAX3221EIDBG4 price MAX3221EIDBG4 stock

Verwandte Bauteile & Begriffe

Texas Instruments MAX3221EIDBG4 MAX3221 MAX3221CAE RS-232 transceiver RS-232 line driver RS-232 line receiver TIA/EIA-232-F IEC 61000-4-2 dual charge-pump circuit receiver enable 3 V to 5.5 V power supply 250 kbps data rate ±15 kV ESD protection 16-pin SSOP SSOP package family surface-mount package industrial temperature grade asynchronous serial communication serial interface IC external surge protection obsolete lifecycle status
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen