MAX3221EIDBG4 - Single-Channel 3V RS-232 Transceiver | Texas Instruments
MPN: MAX3221EIDBG4 ✗ Son Kullanım ZamanıMAX3221EIDBG4 Genel Bakış
An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a serial connector. The transmitter converts TTL or CMOS logic into bipolar RS-232 levels, while the receiver converts the bipolar signal back into logic-compatible levels. The MAX3221 therefore connects an asynchronous communication controller to a serial port without requiring external RS-232 line drivers or receivers.
The MAX3221EIDBG4 offers a flexible 3 V to 5.5 V operating supply and a maximum signaling rate of 250 kbps. According to the manufacturer datasheet, the device meets TIA/EIA-232-F requirements and incorporates a dual charge-pump circuit. Dedicated receiver enable support allows the receiver to be controlled when the serial interface is not active.
The E and I ordering designations identify the industrial-temperature version in the SSOP package family, while G4 identifies the tape-and-reel shipping format. The 16-pin SSOP has a stated body width of approximately 5.30 mm and a package width of 0.209 inch. Lead-free status and industrial temperature grade are explicitly listed for this device.
Typical uses include industrial serial adapters, point-to-point RS-232 links, embedded data acquisition equipment, maintenance interfaces, and legacy peripheral connections. A single transceiver is appropriate when only one RS-232 channel is needed. Multiport systems generally require additional transceiver channels or a multi-channel interface IC.
PCB design should keep charge-pump capacitors and RS-232 connector protection close to the relevant pins. Confirm the complete pin assignment, exposed supply requirements, and recommended capacitor values in the manufacturer datasheet before releasing a layout. External transient protection may still be required when the connector is exposed to severe industrial surge environments.
This product page combines the device specifications, package information, application guidance, lifecycle information, and verified cross-reference findings for faster engineering review. It also highlights the limitation that no independently verified, same-package drop-in alternatives could be confirmed without risking an incorrect PCB substitution.
Drop-in alternatifler için MAX3221EIDBG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
MAX3221CAE
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MAX3221EIDBG4 Özellikler
| Device Type | RS-232 line transceiver |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Communication Standard | TIA/EIA-232-F |
| RS-232 Pin ESD Protection | ±15 kV |
| Human Body Model ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge | ±8 kV |
| IEC 61000-4-2 Air-Gap Discharge | ±15 kV |
| Paket | 16-pin SSOP, 5.30 mm body width |
| Package Width | 0.209 inch |
| Montaj Türü | Surface mount |
| Terminal Count | 16 terminals |
| Temperature Grade | Industrial |
| Lead-Free Status | Lead free |
| Shipping Format | Tape and reel |
| Charge-Pump Supply | Dual charge-pump circuit |
| Receiver Enable | Dedicated receiver enable pin |
MAX3221EIDBG4 0.209 inch Pin Yapısı Kılavuzu
MAX3221EIDBG4 (0.209 inch paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MAX3221EIDBG4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MAX3221EIDBG4 için uygundur 6 uygulamas: Industrial Serial Port Interface, Embedded Data Acquisition Equipment, Legacy Peripheral Connectivity, Field Service and Diagnostics, Security and Access Control Equipment, Instrumentation and Test Equipment.
Industrial Serial Port Interface
The MAX3221EIDBG4 fits point-to-point RS-232 links in industrial equipment because it combines one transmitter and one receiver with a 3 V to 5.5 V supply range and a 250 kbps maximum data rate. Place it between a 3.3 V or 5 V asynchronous controller and an external DB9 or equivalent connector. The listed ±15 kV RS-232-pin ESD protection improves robustness at the interface boundary, while the industrial temperature grade supports equipment operating outside typical consumer environments.
Önerilen
Embedded Data Acquisition Equipment
The MAX3221EIDBG4 can connect a data-acquisition controller to an RS-232 service port while operating from the same 3 V to 5.5 V range as many embedded processors. A 250 kbps data rate is suitable for configuration commands, status packets, and periodic measurements rather than continuous high-bandwidth transfer. Use the dedicated receiver-enable function to control bus participation, and follow the manufacturer charge-pump capacitor recommendations closely to maintain stable signal generation.
Önerilen
Legacy Peripheral Connectivity
The MAX3221EIDBG4 is useful when maintaining equipment that relies on a single RS-232 port for a printer, controller, test fixture, or legacy peripheral. Its one-driver and one-receiver arrangement matches point-to-point serial links and reduces board area compared with a multi-channel interface. The 16-pin SSOP package supports compact designs, but engineers should verify the package drawing, pin numbering, and charge-pump capacitor network against the manufacturer datasheet before reusing an existing footprint.
Önerilen
Field Service and Diagnostics
The MAX3221EIDBG4 supports field-service and diagnostic ports that need a short-range wired connection between equipment and a maintenance computer. Its 250 kbps maximum rate accommodates command exchange and diagnostic output, while the specified IEC 61000-4-2 air-gap and contact discharge levels add protection at connector-facing pins. System designers should still evaluate cable length, common-mode grounding, connector shielding, and external surge protection according to the installation environment.
Önerilen
Security and Access Control Equipment
The MAX3221EIDBG4 can provide a wired diagnostic or configuration channel in access-control and security equipment where a single RS-232 link replaces a disposable connector arrangement. The 3 V to 5.5 V supply compatibility supports embedded logic rails, and the listed ±15 kV ESD protection is relevant when the serial connector is accessible to personnel. Keep the interface away from unprotected antenna structures and use appropriate enclosure, filtering, and grounding controls.
Önerilen
Instrumentation and Test Equipment
The MAX3221EIDBG4 is suitable for simple RS-232 control and telemetry interfaces in laboratory or field instrumentation. One channel is enough for a host-to-instrument command link with limited return data, and the 250 kbps rate supports configuration and status traffic. The device's industrial temperature grade and specified ESD levels are useful in controlled equipment environments. For bench-top instruments exposed to frequent connector handling, add appropriate external protection and follow the manufacturer's application circuit.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MAX3221EIDBG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Device Type | Single-channel RS-232 transceiver |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Package | 16-pin SSOP |
| Brand | Texas Instruments |
| RS-232 Pin ESD Protection | ±15 kV |
| Temperature Grade | Industrial |
| Lifecycle Status | Obsolete |
Ana Farklılayıcılar
- Compact single-channel RS-232 interface (karşılaştırma:Multi-channel RS-232 interface)
- Wide logic-side supply compatibility (karşılaştırma:5 V-only RS-232 interface)
- Built-in connector-side ESD protection (karşılaştırma:RS-232 transceiver without enhanced ESD)
- Adequate signaling rate for control links (karşılaştırma:Low-rate RS-232 transceiver)
Tasarım Notları
Place the charge-pump capacitors and the required RS-232 connector protection components close to their associated device pins. Keep the driver output and receiver input traces away from switching nodes and high-current paths to limit capacitive coupling. Use the manufacturer application circuit as the layout reference because trace length, ground placement, and capacitor return paths affect charge-pump stability and the integrity of the bipolar RS-232 waveform.
Do not substitute an electrically similar MAX3221-family device without checking the physical package and every pin assignment. A related ordering code may use a different package, temperature grade, enable configuration, or capacitor arrangement. For this obsolete ordering code, request lifecycle confirmation through the Request a Quote form and preserve the original manufacturer footprint when maintaining an existing PCB.
Keep the RS-232 connector interface physically separated from sensitive analog sections, clocks, and switching regulators. Connect the interface ground according to the system grounding strategy, and use a short return path for connector currents. The device's built-in ESD ratings protect specified pins, but external protection and cable design may still be necessary when the port experiences severe surges or long exposed cable runs.
Uyumluluk Bilgisi
The part is identified as lead free. RoHS, REACH, halogen-free, and conflict-minerals status are not established by the available product information.