MAX3221EIDBG4 - Single-Channel 3V RS-232 Transceiver | Texas Instruments
MPN: MAX3221EIDBG4 ✗ Cuối đờiMAX3221EIDBG4 Tóm tắt
An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a serial connector. The transmitter converts TTL or CMOS logic into bipolar RS-232 levels, while the receiver converts the bipolar signal back into logic-compatible levels. The MAX3221 therefore connects an asynchronous communication controller to a serial port without requiring external RS-232 line drivers or receivers.
The MAX3221EIDBG4 offers a flexible 3 V to 5.5 V operating supply and a maximum signaling rate of 250 kbps. According to the manufacturer datasheet, the device meets TIA/EIA-232-F requirements and incorporates a dual charge-pump circuit. Dedicated receiver enable support allows the receiver to be controlled when the serial interface is not active.
The E and I ordering designations identify the industrial-temperature version in the SSOP package family, while G4 identifies the tape-and-reel shipping format. The 16-pin SSOP has a stated body width of approximately 5.30 mm and a package width of 0.209 inch. Lead-free status and industrial temperature grade are explicitly listed for this device.
Typical uses include industrial serial adapters, point-to-point RS-232 links, embedded data acquisition equipment, maintenance interfaces, and legacy peripheral connections. A single transceiver is appropriate when only one RS-232 channel is needed. Multiport systems generally require additional transceiver channels or a multi-channel interface IC.
PCB design should keep charge-pump capacitors and RS-232 connector protection close to the relevant pins. Confirm the complete pin assignment, exposed supply requirements, and recommended capacitor values in the manufacturer datasheet before releasing a layout. External transient protection may still be required when the connector is exposed to severe industrial surge environments.
This product page combines the device specifications, package information, application guidance, lifecycle information, and verified cross-reference findings for faster engineering review. It also highlights the limitation that no independently verified, same-package drop-in alternatives could be confirmed without risking an incorrect PCB substitution.
Bộ thay thế dễ dàng lắp đặt cho MAX3221EIDBG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MAX3221CAE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3221EIDBG4 Thông số kỹ thuật
| Device Type | RS-232 line transceiver |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Communication Standard | TIA/EIA-232-F |
| RS-232 Pin ESD Protection | ±15 kV |
| Human Body Model ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge | ±8 kV |
| IEC 61000-4-2 Air-Gap Discharge | ±15 kV |
| Hộp | 16-pin SSOP, 5.30 mm body width |
| Package Width | 0.209 inch |
| Kiểu lắp đặt | Surface mount |
| Terminal Count | 16 terminals |
| Temperature Grade | Industrial |
| Lead-Free Status | Lead free |
| Shipping Format | Tape and reel |
| Charge-Pump Supply | Dual charge-pump circuit |
| Receiver Enable | Dedicated receiver enable pin |
Hướng dẫn cấu hình chân MAX3221EIDBG4 0.209 inch
Cấu hình chân cho MAX3221EIDBG4 (0.209 inch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3221EIDBG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3221EIDBG4 phù hợp cho 6 Áp dụngs: Industrial Serial Port Interface, Embedded Data Acquisition Equipment, Legacy Peripheral Connectivity, Field Service and Diagnostics, Security and Access Control Equipment, Instrumentation and Test Equipment.
Industrial Serial Port Interface
The MAX3221EIDBG4 fits point-to-point RS-232 links in industrial equipment because it combines one transmitter and one receiver with a 3 V to 5.5 V supply range and a 250 kbps maximum data rate. Place it between a 3.3 V or 5 V asynchronous controller and an external DB9 or equivalent connector. The listed ±15 kV RS-232-pin ESD protection improves robustness at the interface boundary, while the industrial temperature grade supports equipment operating outside typical consumer environments.
Được đề xuất
Embedded Data Acquisition Equipment
The MAX3221EIDBG4 can connect a data-acquisition controller to an RS-232 service port while operating from the same 3 V to 5.5 V range as many embedded processors. A 250 kbps data rate is suitable for configuration commands, status packets, and periodic measurements rather than continuous high-bandwidth transfer. Use the dedicated receiver-enable function to control bus participation, and follow the manufacturer charge-pump capacitor recommendations closely to maintain stable signal generation.
Được đề xuất
Legacy Peripheral Connectivity
The MAX3221EIDBG4 is useful when maintaining equipment that relies on a single RS-232 port for a printer, controller, test fixture, or legacy peripheral. Its one-driver and one-receiver arrangement matches point-to-point serial links and reduces board area compared with a multi-channel interface. The 16-pin SSOP package supports compact designs, but engineers should verify the package drawing, pin numbering, and charge-pump capacitor network against the manufacturer datasheet before reusing an existing footprint.
Được đề xuất
Field Service and Diagnostics
The MAX3221EIDBG4 supports field-service and diagnostic ports that need a short-range wired connection between equipment and a maintenance computer. Its 250 kbps maximum rate accommodates command exchange and diagnostic output, while the specified IEC 61000-4-2 air-gap and contact discharge levels add protection at connector-facing pins. System designers should still evaluate cable length, common-mode grounding, connector shielding, and external surge protection according to the installation environment.
Được đề xuất
Security and Access Control Equipment
The MAX3221EIDBG4 can provide a wired diagnostic or configuration channel in access-control and security equipment where a single RS-232 link replaces a disposable connector arrangement. The 3 V to 5.5 V supply compatibility supports embedded logic rails, and the listed ±15 kV ESD protection is relevant when the serial connector is accessible to personnel. Keep the interface away from unprotected antenna structures and use appropriate enclosure, filtering, and grounding controls.
Được đề xuất
Instrumentation and Test Equipment
The MAX3221EIDBG4 is suitable for simple RS-232 control and telemetry interfaces in laboratory or field instrumentation. One channel is enough for a host-to-instrument command link with limited return data, and the 250 kbps rate supports configuration and status traffic. The device's industrial temperature grade and specified ESD levels are useful in controlled equipment environments. For bench-top instruments exposed to frequent connector handling, add appropriate external protection and follow the manufacturer's application circuit.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3221EIDBG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Device Type | Single-channel RS-232 transceiver |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Package | 16-pin SSOP |
| Brand | Texas Instruments |
| RS-232 Pin ESD Protection | ±15 kV |
| Temperature Grade | Industrial |
| Lifecycle Status | Obsolete |
Bảo phân biệt quan trọng
- Compact single-channel RS-232 interface (vsMulti-channel RS-232 interface)
- Wide logic-side supply compatibility (vs5 V-only RS-232 interface)
- Built-in connector-side ESD protection (vsRS-232 transceiver without enhanced ESD)
- Adequate signaling rate for control links (vsLow-rate RS-232 transceiver)
Ghi chú thiết kế
Place the charge-pump capacitors and the required RS-232 connector protection components close to their associated device pins. Keep the driver output and receiver input traces away from switching nodes and high-current paths to limit capacitive coupling. Use the manufacturer application circuit as the layout reference because trace length, ground placement, and capacitor return paths affect charge-pump stability and the integrity of the bipolar RS-232 waveform.
Do not substitute an electrically similar MAX3221-family device without checking the physical package and every pin assignment. A related ordering code may use a different package, temperature grade, enable configuration, or capacitor arrangement. For this obsolete ordering code, request lifecycle confirmation through the Request a Quote form and preserve the original manufacturer footprint when maintaining an existing PCB.
Keep the RS-232 connector interface physically separated from sensitive analog sections, clocks, and switching regulators. Connect the interface ground according to the system grounding strategy, and use a short return path for connector currents. The device's built-in ESD ratings protect specified pins, but external protection and cable design may still be necessary when the port experiences severe surges or long exposed cable runs.
Thông tin tuân thủ
The part is identified as lead free. RoHS, REACH, halogen-free, and conflict-minerals status are not established by the available product information.