Analog Devices

MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

Teilenummer: MAX350CWN+ ✓ Aktiv
±2.7 V to ±8 V Vdss 100 ohm maximum Rds(on) 18-pin wide SOIC Package
MOQ: 1 |

MAX350CWN+ Übersicht

The Analog Devices MAX350CWN+ is a serially controlled, low-voltage dual 4:1 analog multiplexer with two independent 4:1 switch sections in an 18-pin wide SOIC package. Its maximum on-resistance is 100 ohm, with on-resistance matching between switches specified to 16 ohm maximum and flatness specified to 10 ohm maximum over the operating signal range. The device supports bidirectional signal conduction.

A multiplexer is a semiconductor switch that connects one of several inputs to a common output. The 4:1 architecture reduces the number of physical signal connections required in instrumentation, test, measurement, and data-acquisition systems. The MAX350 family combines eight switched signal paths into two serial-controlled 4:1 groups, making it useful when a system must route several low-voltage analog signals while keeping board wiring and control logic compact.

The MAX350CWN+ uses serial control to select the active input path. According to the Analog Devices MAX350 product page, the MAX349 and MAX350 multiplexers conduct equally well in either direction and use CMOS implementations. Their specified dual-supply operating range extends from ±2.7 V to ±8 V. The MAX350CWN+ is identified by the distributor listings as a two-circuit, 4:1, 100 ohm device in an 18-SOIC package.

On-resistance matching is particularly important when several channels carry similar or low-level analog signals. A matched network reduces channel-dependent gain and attenuation errors introduced by the multiplexer. The specified 100 ohm maximum on-resistance also indicates that the device is intended for low-voltage signal-routing applications where substantially lower resistance is generally not required.

Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and industrial control modules. In these systems, the MAX350CWN+ can present one selected signal to a measurement or conversion channel while a microcontroller or test controller operates the serial interface. The dual 4:1 organization allows two multiplexed groups to support paired, differential, or otherwise related signal paths.

PCB implementation requires careful placement of the interface and routed signal nets to limit coupling, crosstalk, and impedance discontinuities. Keep serial-control traces away from sensitive analog paths, use a continuous ground reference, and observe the manufacturer's recommended bypass-capacitor and layout practices. Confirm supply sequencing, logic levels, input-voltage limits, and the exact 18-pin pinout against the manufacturer datasheet before fabrication.

This product record combines the manufacturer product description with distributor package and channel information, then adds practical routing, matching, and selection guidance. It also identifies genuine same-family drop-in candidates while clearly separating verified facts from parameters that require confirmation from the manufacturer datasheet.

Drop-in-Alternativen für MAX350CWN+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit MAX350CWN+ (gleiche Bauform und Footprint) – abweichend in Number of Channels, Package.

Analog Devices
Number of Channels: 8 channels as two 4-channel banks
Package: 18-pin wide SOIC (WSOIC-18)
Vergleichen mit MAX350CWN+ →

MAX350CWN

✅ Drop-In
📦 18-SOIC
Same MAX350 dual 4:1 function and 18-SOIC footprint; plus-suffix ordering definition differs by 0% in confirmed channel count and maximum on-resistance.

📋 Referenzalternative (nicht im Katalog)

MAX350EWN+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Analog Devices
📦 18-SOIC
Dual 4:1 multiplexer, 2 circuits · Serial · 2.7 V to 16 V · 100 ohm · 16 ohm maximum · 10 ohm maximum · Bidirectional · CMOS

Preis auf Anfrage

Datenblatt ansehen →

MAX350EWN+T

✅ Drop-In
📦 18-SOIC
Same dual 4:1 MAX350 function and 18-SOIC footprint; E temperature-grade suffix differs while confirmed on-resistance remains 100 ohm maximum.

📋 Referenzalternative (nicht im Katalog)

MAX350CWN+T

✅ Drop-In
📦 18-SOIC
Same dual 4:1 MAX350 function and 18-SOIC footprint; T adds the manufacturer’s tape-and-reel shipping designation without changing confirmed electrical parameters.

📋 Referenzalternative (nicht im Katalog)

MAX350CWN+ Technische Daten

Multiplexer Configuration Dual 4:1
Number of Circuits 2 circuits
Number of Channels 8 channels
On-Resistance 100 ohm maximum
On-Resistance Matching 16 ohm maximum
On-Resistance Flatness 10 ohm maximum over specified signal range
Signal Conduction Direction Bidirectional
Control Interface Serial
Dual-Supply Operating Range ±2.7 V to ±8 V
Technology CMOS
Gehäuse 18-pin wide SOIC
Package Dimensions 7.50 mm wide
Montageart Surface mount

MAX350CWN+ 7.50 mm wide Pinbelegungsleitfaden

Pinbelegung für MAX350CWN+ (7.50 mm wide-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MAX350CWN+ im 7.50 mm wide-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MAX350CWN+.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MAX350CWN+ ist geeignet für 6 Anwendungs: Automated Test Equipment, Data Acquisition Systems, Precision Signal Routing, Industrial Control Modules, Portable Measurement Instruments, Communications and Interface Routing.

🏭

Automated Test Equipment

The MAX350CWN+ fits automated test systems that must connect several low-voltage signals to a shared measurement channel. Its dual 4:1 organization provides two independent groups of four switched inputs, reducing the number of external signal connections required at a test fixture. Serial control allows a controller to select paths without dedicating one parallel control line per channel. The 100 ohm maximum on-resistance is suitable when source impedance and measurement accuracy permit that resistance. Engineers should calculate the resulting divider error with the source and input impedances, while the specified 16 ohm maximum switch-to-switch matching helps limit channel-dependent errors.

📊

Data Acquisition Systems

The MAX350CWN+ can route multiple analog inputs into a shared data-acquisition front end while its serial interface reduces backplane wiring. Two independent 4:1 sections allow related signal groups, such as paired inputs, to be selected with a common controller. Bidirectional conduction is useful when source and destination roles can change. Designers should compare the 100 ohm maximum on-resistance with the selected sensor and converter input impedances, and should assess the 10 ohm maximum on-resistance flatness across the signal range. Decoupling and grounding remain important because the device can operate from dual supplies of ±2.7 V to ±8 V.

🔧

Precision Signal Routing

The MAX350CWN+ is appropriate for multiplexed low-level signal routing where repeatable channel behavior is more important than extremely low resistance. On-resistance is matched between switches to 16 ohm maximum, which limits switch-induced gain differences between channels, while flatness is specified to 10 ohm maximum over the operating signal range. These characteristics help engineers select a channel without introducing large channel-to-channel attenuation changes. The architecture also supports bidirectional routing, allowing the same switch network to be used in measurement and stimulus paths. Source impedance, amplifier input impedance, leakage, and injection error should be evaluated together in the complete signal chain.

🏭

Industrial Control Modules

The MAX350CWN+ can reduce analog-routing complexity in industrial control equipment by connecting several process signals to one controller or measurement channel. Its eight total channels are divided into two 4:1 sections, allowing two related signal groups to be multiplexed within an 18-pin wide SOIC footprint. Serial control supports integration with a microcontroller or test sequencer. For equipment using 24 V field wiring, the MAX350 is not connected directly to that rail; interface circuitry must translate field-level signals to the device’s ±2.7 V to ±8 V dual-supply range or supported single-supply conditions. Production designs should also include protection against transients and verify logic-level compatibility.

📱

Portable Measurement Instruments

The MAX350CWN+ supports compact handheld or portable measurement instruments where multiple sensors must reach a shared analog front end without a large connector or matrix switch. The serial-control architecture reduces control wiring, while the 18-SOIC package preserves board area. Its bidirectional conduction allows signal paths to be reused for excitation and measurement where the system architecture permits. Designers should include local bypass capacitors, maintain a low-impedance ground plane, and keep serial clock and data traces away from sensitive input nets. Because the switch resistance can reach 100 ohm, error calculations must include sensor impedance and downstream amplifier bias current to prevent gain errors.

🌐

Communications and Interface Routing

The MAX350CWN+ can serve as a low-voltage auxiliary signal router in communications equipment when several control, status, or monitor lines must reach a common interface controller. Its serial selection mechanism limits parallel control overhead, and the bidirectional CMOS switches accommodate varied routing directions. The MAX350 is intended for low-voltage multiplexing rather than high-impedance RF distribution, so engineers should verify bandwidth, capacitance, and insertion-loss behavior against the manufacturer data. Keep the serial bus away from high-energy clock and power paths, use a continuous reference plane, and place supply bypass capacitors close to the device. Firmware should avoid changing routes during sensitive conversions unless the system timing permits the resulting transient.

What is the MAX350CWN+?
The MAX350CWN+ is a serially controlled, low-voltage dual 4:1 analog multiplexer from Analog Devices, providing two independent 4:1 switch groups and eight total signal paths. According to the Analog Devices MAX350 product page, the MAX350 family consists of CMOS devices that conduct equally well in either direction. The MAX350CWN+ is packaged in an 18-pin wide SOIC and has a maximum on-resistance of 100 ohm.
How many channels and circuits does MAX350CWN+ have?
The MAX350CWN+ contains two independent 4:1 circuits, giving it eight switched channels in total. Distributor product descriptions identify the device as a two-circuit IC switch with a 4:1 configuration and 100 ohm maximum on-resistance. The Analog Devices MAX350 product page describes the MAX349 and MAX350 as 8-channel and dual 4-channel serially controlled multiplexers.
What is the on-resistance of MAX350CWN+?
The MAX350CWN+ has a maximum on-resistance of 100 ohm. According to the Analog Devices MAX350 product page, on-resistance is matched between switches to 16 ohm maximum and remains flat within 10 ohm maximum over the specified signal range. These matching and flatness figures are useful when assessing channel-to-channel accuracy in low-level analog measurement systems.
What voltage supplies can power the MAX350CWN+?
The MAX350CWN+ can operate from dual supplies ranging from ±2.7 V to ±8 V, according to the Analog Devices MAX350 product page. It also supports single-supply operation beginning at +2 V. Confirm the exact maximum single-supply voltage, absolute maximum ratings, and supply combinations in the manufacturer datasheet before finalizing the power architecture.
Is the MAX350CWN+ suitable for bidirectional signals?
Yes, the MAX350CWN+ is suitable for bidirectional signal routing because its CMOS switches conduct equally well in either direction. According to the Analog Devices MAX350 product page, this characteristic applies to the MAX350 family. Bidirectional operation allows the same multiplexer to route inputs toward a converter, test instrument, or other downstream measurement block.
Where can I download the MAX350CWN+ datasheet PDF?
The MAX350CWN+ datasheet and supporting documentation are available through the official Analog Devices MAX350 product page at https://www.analog.com/en/products/max350.html. Select the Data Sheet document listed under the product documentation. The manufacturer page identifies the document as Data Sheet Rev. 1 and provides product-selection and ordering information for the MAX349 and MAX350 families.
Where can I find the MAX350CWN+ pinout?
The MAX350CWN+ pin assignment is shown in the pin-configuration section of the official Analog Devices MAX350 data sheet linked from the product page. The distributor listings identify the component as an 18-SOIC device. Before assigning PCB nets, use the manufacturer drawing for the complete 18-pin wide SOIC numbering and verify every supply, ground, control, and switched-signal connection.
MAX350CWN+ vs MAX350CWN — which one should I choose?
MAX350CWN+ and MAX350CWN are functionally equivalent ordering forms of the MAX350 device in the same 18-pin SOIC family, with the plus suffix identifying the enhanced product form. The exact ordering-code definitions should be checked in the manufacturer data sheet. For an existing MAX350CWN+ footprint, MAX350CWN can serve as a same-package candidate, subject to temperature-grade and ordering-code review.
When should I choose MAX350CWN+ over MAX349?
Choose MAX350CWN+ when the design requires two independent 4:1 analog multiplexer sections with serial control and an 18-pin wide SOIC footprint. The Analog Devices MAX350 family is the dual 4-channel option, whereas the MAX349 is the 8-channel family member. A design should not substitute one architecture for the other without verifying pin assignments, channel count, and control protocol.
What is the best drop-in replacement for MAX350CWN+?
MAX350CWN is the closest same-package replacement candidate for MAX350CWN+ because it retains the MAX350 dual 4:1 architecture, 100 ohm on-resistance, 18-SOIC package, and serial-control function. The MAX350EWN and MAX350CWN+T ordering variants provide additional candidates for temperature-grade or packaging review. Verify the exact suffix, pinout, temperature range, and lifecycle status in the manufacturer documentation.
Can MAX350EWN+T replace MAX350CWN+?
The MAX350EWN+T is a MAX350-family candidate for the same 18-pin wide SOIC footprint, but replacement depends on the exact suffix definition, temperature grade, and ordering requirements. Its MAX350 architecture retains the dual 4:1 multiplexer function and 100 ohm maximum on-resistance. Compare the manufacturer pin configuration and ordering table before treating it as a drop-in substitution.
Where can I buy MAX350CWN+ and check its availability?
Use the Request a Quote form on this page to request MAX350CWN+ availability, current commercial terms, and a lead-time quotation. The manufacturer product page lists the MAX350 family as production, while distributor search results identify MAX350CWN+ in an 18-SOIC package. XAIPART’s quote team can confirm exact suffix matching and order quantities without relying on a static price.
What is the price of MAX350CWN+?
Use the Request a Quote form on this page for the current MAX350CWN+ commercial price and quantity schedule. The manufacturer product page displays a family-level starting list value, but that figure is not treated as an exact unit-price schedule for this ordering code. The quote form allows the exact MPN, package suffix, quantity, and delivery requirements to be confirmed.
What is the lead time and stock status for MAX350CWN+?
Submit the MAX350CWN+ MPN through the Request a Quote form on this page to obtain current lead time, minimum order quantity, and available quantity. The Analog Devices MAX350 product page identifies the family as production, and distributor search results show listings for MAX350CWN+, but those listings do not establish a guaranteed XAIPART allocation. A quotation confirms the current supply position for the exact suffix.
Is MAX350CWN+ RoHS compliant?
The RoHS status of MAX350CWN+ must be confirmed from the manufacturer’s current material or compliance declaration for the exact ordering code. The verified product information identifies the MAX350 family and its 18-pin package but does not provide a specific RoHS statement. Request the manufacturer compliance record or a lot-specific declaration before treating the device as compliant for a regulated production release.
What are the key specifications of MAX350CWN+ that engineers should know?
The key MAX350CWN+ specifications are its dual 4:1 configuration, two independent circuits, eight total channels, 100 ohm maximum on-resistance, 16 ohm maximum on-resistance matching, and 10 ohm maximum flatness over the specified signal range. It uses serial control, supports bidirectional CMOS signal conduction, operates from ±2.7 V to ±8 V in dual-supply mode, and uses an 18-pin wide SOIC package.
What can replace MAX350CWN+?
MAX350CWN, MAX350EWN, MAX350EWN+T, and MAX350CWN+T are the identified MAX350-family candidates for a MAX350CWN+ replacement review. They retain the family’s serial-controlled dual 4:1 function and 18-pin wide SOIC format, while suffix differences may affect packaging or temperature grade. Confirm the ordering-code definition and compare the manufacturer pin and specification tables before approving a substitution.

Technische Referenzdaten für MAX350CWN+ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MAX350CWN+ for a new design that requires a serial-controlled, dual 4:1 analog multiplexer in an 18-pin wide SOIC package, especially when two related low-voltage signal groups must be routed to shared measurement resources. Its 100 ohm maximum on-resistance is appropriate for applications where source and receiver impedances limit the resulting attenuation, while the 16 ohm maximum matching specification helps control channel-to-channel variation. MAX350CWN is the closest direct ordering-form candidate when the MAX350CWN+ enhanced suffix is not required. Consider MAX350EWN when a different manufacturer temperature-grade suffix is appropriate for the deployment, and use MAX350EWN+T or MAX350CWN+T when their documented grade and tape-and-reel logistics match production needs. In every case, verify the manufacturer ordering table, complete 18-pin configuration, operating-temperature range, supply limits, and interface timing before releasing a substitution.

Vergleich mit Alternativen

Parameter Dieses Produkt MAX350CWN MAX350EWN MAX350EWN+T MAX350CWN+T
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 18-SOIC 18-SOIC 18-SOIC 18-SOIC 18-SOIC
Multiplexer Configuration Dual 4:1 Dual 4:1 Dual 4:1 Dual 4:1 Dual 4:1
Number of Circuits 2 circuits 2 circuits 2 circuits 2 circuits 2 circuits
Total Channels 8 channels 8 channels 8 channels 8 channels 8 channels
Maximum On-Resistance 100 ohm 100 ohm 100 ohm 100 ohm 100 ohm
Control Interface Serial Serial Serial Serial Serial
Dual-Supply Operating Range ±2.7 V to ±8 V ±2.7 V to ±8 V ±2.7 V to ±8 V ±2.7 V to ±8 V ±2.7 V to ±8 V
Signal Conduction Bidirectional Bidirectional Bidirectional Bidirectional Bidirectional
Ordering-Suffix Difference CWN+ enhanced ordering form CWN without plus suffix E temperature-grade suffix E temperature-grade and tape-and-reel suffix C temperature-grade and tape-and-reel suffix

Wichtigste Unterscheidungsmerkmale

  • Two independent 4:1 sections in one device (vs. MAX350CWN)
  • Specified channel matching for measurement accuracy (vs. MAX350EWN+T)
  • Bidirectional low-voltage signal routing (vs. MAX350CWN+T)

Designhinweise

Route the serial clock and data lines away from switched analog inputs and sensitive amplifier inputs. Place the device close to the sources of the signals it selects, maintain a continuous ground plane, and avoid long parallel paths between the multiplexer and receiver. Use the manufacturer’s 18-pin package drawing to confirm pin order, exposed connections, and the orientation of pin 1 before releasing the PCB layout.

Include the switch resistance when calculating signal attenuation. Estimated with a 100 ohm maximum switch resistance and a 10 kilohm receiver input, the maximum resistive divider would attenuate the signal to approximately 99.0 percent of its original value. Actual error also depends on leakage, source impedance, and bandwidth. Evaluate on-resistance matching and the 16 ohm maximum matching specification as separate contributors to channel-to-channel variation.

Bypass each supply connection near the device using the capacitance and placement specified by the manufacturer. The MAX350 family supports dual supplies from ±2.7 V to ±8 V and single-supply operation beginning at +2 V. Confirm the complete allowable supply combinations, logic thresholds, and sequencing requirements before power-up. Use separate, low-impedance return paths for analog and digital currents to reduce supply coupling through the shared ground network.

Do not interpret the family-level product-page starting price as an exact MAX350CWN+ unit price, and do not approve a suffix substitution without reviewing the manufacturer ordering table. The MAX350CWN, MAX350EWN, MAX350EWN+T, and MAX350CWN+T candidates differ in ordering-code meaning even though they retain the same core dual 4:1 architecture and 18-SOIC footprint.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The MAX350 family is identified as production by Analog Devices. A specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for MAX350CWN+ was not identified in the available product information.

Daten verifiziert am: 2026-11-14 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MAX350CWN+ datasheet MAX350CWN+ pinout MAX350CWN+ datasheet pdf Analog Devices MAX350CWN+ MAX350CWN+ 18-SOIC MAX350CWN+ dual 4:1 multiplexer MAX350CWN+ 100 ohm on resistance MAX350CWN+ equivalent MAX350CWN+ replacement MAX350CWN+ vs MAX350CWN MAX350CWN+ price MAX350CWN+ stock MAX350CWN+ application circuit MAX350 18-SOIC pinout MAX350CWN+ drop-in replacement

Verwandte Bauteile & Begriffe

Analog Devices MAX350CWN+ MAX350 MAX349 MAX350CWN MAX350EWN MAX350EWN+T MAX350CWN+T dual 4:1 analog multiplexer serially controlled multiplexer analog switch interface IC CMOS bidirectional signal conduction on-resistance on-resistance matching on-resistance flatness 18-SOIC wide SOIC surface-mount package dual power supply data acquisition automated test equipment instrumentation industrial control
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen