MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MPN: MAX350CWN+ ✓ 啟用中MAX350CWN+ 概覽
A multiplexer is a semiconductor switch that connects one of several inputs to a common output. The 4:1 architecture reduces the number of physical signal connections required in instrumentation, test, measurement, and data-acquisition systems. The MAX350 family combines eight switched signal paths into two serial-controlled 4:1 groups, making it useful when a system must route several low-voltage analog signals while keeping board wiring and control logic compact.
The MAX350CWN+ uses serial control to select the active input path. According to the Analog Devices MAX350 product page, the MAX349 and MAX350 multiplexers conduct equally well in either direction and use CMOS implementations. Their specified dual-supply operating range extends from ±2.7 V to ±8 V. The MAX350CWN+ is identified by the distributor listings as a two-circuit, 4:1, 100 ohm device in an 18-SOIC package.
On-resistance matching is particularly important when several channels carry similar or low-level analog signals. A matched network reduces channel-dependent gain and attenuation errors introduced by the multiplexer. The specified 100 ohm maximum on-resistance also indicates that the device is intended for low-voltage signal-routing applications where substantially lower resistance is generally not required.
Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and industrial control modules. In these systems, the MAX350CWN+ can present one selected signal to a measurement or conversion channel while a microcontroller or test controller operates the serial interface. The dual 4:1 organization allows two multiplexed groups to support paired, differential, or otherwise related signal paths.
PCB implementation requires careful placement of the interface and routed signal nets to limit coupling, crosstalk, and impedance discontinuities. Keep serial-control traces away from sensitive analog paths, use a continuous ground reference, and observe the manufacturer's recommended bypass-capacitor and layout practices. Confirm supply sequencing, logic levels, input-voltage limits, and the exact 18-pin pinout against the manufacturer datasheet before fabrication.
This product record combines the manufacturer product description with distributor package and channel information, then adds practical routing, matching, and selection guidance. It also identifies genuine same-family drop-in candidates while clearly separating verified facts from parameters that require confirmation from the manufacturer datasheet.
直接替換替代品,適用於 MAX350CWN+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX350CWN+ (相同外形與佔位) — 差異在於 Number of Channels, Package.
MAX350CWN
✅ 直接替換📋 參考替代品(不在目錄中)
MAX350EWN+
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MAX350EWN+T
✅ 直接替換📋 參考替代品(不在目錄中)
MAX350CWN+T
✅ 直接替換📋 參考替代品(不在目錄中)
MAX350CWN+ 規格
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| Number of Channels | 8 channels |
| On-Resistance | 100 ohm maximum |
| On-Resistance Matching | 16 ohm maximum |
| On-Resistance Flatness | 10 ohm maximum over specified signal range |
| Signal Conduction Direction | Bidirectional |
| Control Interface | Serial |
| Dual-Supply Operating Range | ±2.7 V to ±8 V |
| Technology | CMOS |
| 封裝 | 18-pin wide SOIC |
| Package Dimensions | 7.50 mm wide |
| 安裝類型 | Surface mount |
MAX350CWN+ 7.50 mm wide 腳位配置指南
MAX350CWN+(7.50 mm wide 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX350CWN+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX350CWN+ 適用於 6 應用s: Automated Test Equipment, Data Acquisition Systems, Precision Signal Routing, Industrial Control Modules, Portable Measurement Instruments, Communications and Interface Routing.
Automated Test Equipment
The MAX350CWN+ fits automated test systems that must connect several low-voltage signals to a shared measurement channel. Its dual 4:1 organization provides two independent groups of four switched inputs, reducing the number of external signal connections required at a test fixture. Serial control allows a controller to select paths without dedicating one parallel control line per channel. The 100 ohm maximum on-resistance is suitable when source impedance and measurement accuracy permit that resistance. Engineers should calculate the resulting divider error with the source and input impedances, while the specified 16 ohm maximum switch-to-switch matching helps limit channel-dependent errors.
推薦
Data Acquisition Systems
The MAX350CWN+ can route multiple analog inputs into a shared data-acquisition front end while its serial interface reduces backplane wiring. Two independent 4:1 sections allow related signal groups, such as paired inputs, to be selected with a common controller. Bidirectional conduction is useful when source and destination roles can change. Designers should compare the 100 ohm maximum on-resistance with the selected sensor and converter input impedances, and should assess the 10 ohm maximum on-resistance flatness across the signal range. Decoupling and grounding remain important because the device can operate from dual supplies of ±2.7 V to ±8 V.
推薦
Precision Signal Routing
The MAX350CWN+ is appropriate for multiplexed low-level signal routing where repeatable channel behavior is more important than extremely low resistance. On-resistance is matched between switches to 16 ohm maximum, which limits switch-induced gain differences between channels, while flatness is specified to 10 ohm maximum over the operating signal range. These characteristics help engineers select a channel without introducing large channel-to-channel attenuation changes. The architecture also supports bidirectional routing, allowing the same switch network to be used in measurement and stimulus paths. Source impedance, amplifier input impedance, leakage, and injection error should be evaluated together in the complete signal chain.
推薦
Industrial Control Modules
The MAX350CWN+ can reduce analog-routing complexity in industrial control equipment by connecting several process signals to one controller or measurement channel. Its eight total channels are divided into two 4:1 sections, allowing two related signal groups to be multiplexed within an 18-pin wide SOIC footprint. Serial control supports integration with a microcontroller or test sequencer. For equipment using 24 V field wiring, the MAX350 is not connected directly to that rail; interface circuitry must translate field-level signals to the device’s ±2.7 V to ±8 V dual-supply range or supported single-supply conditions. Production designs should also include protection against transients and verify logic-level compatibility.
推薦
Portable Measurement Instruments
The MAX350CWN+ supports compact handheld or portable measurement instruments where multiple sensors must reach a shared analog front end without a large connector or matrix switch. The serial-control architecture reduces control wiring, while the 18-SOIC package preserves board area. Its bidirectional conduction allows signal paths to be reused for excitation and measurement where the system architecture permits. Designers should include local bypass capacitors, maintain a low-impedance ground plane, and keep serial clock and data traces away from sensitive input nets. Because the switch resistance can reach 100 ohm, error calculations must include sensor impedance and downstream amplifier bias current to prevent gain errors.
推薦
Communications and Interface Routing
The MAX350CWN+ can serve as a low-voltage auxiliary signal router in communications equipment when several control, status, or monitor lines must reach a common interface controller. Its serial selection mechanism limits parallel control overhead, and the bidirectional CMOS switches accommodate varied routing directions. The MAX350 is intended for low-voltage multiplexing rather than high-impedance RF distribution, so engineers should verify bandwidth, capacitance, and insertion-loss behavior against the manufacturer data. Keep the serial bus away from high-energy clock and power paths, use a continuous reference plane, and place supply bypass capacitors close to the device. Firmware should avoid changing routes during sensitive conversions unless the system timing permits the resulting transient.
推薦
推薦產品摘要
工程參考資料,適用於 MAX350CWN+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX350CWN | MAX350EWN | MAX350EWN+T | MAX350CWN+T |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 18-SOIC | 18-SOIC | 18-SOIC | 18-SOIC | 18-SOIC |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Total Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Maximum On-Resistance | 100 ohm | 100 ohm | 100 ohm | 100 ohm | 100 ohm |
| Control Interface | Serial | Serial | Serial | Serial | Serial |
| Dual-Supply Operating Range | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V |
| Signal Conduction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Ordering-Suffix Difference | CWN+ enhanced ordering form | CWN without plus suffix | E temperature-grade suffix | E temperature-grade and tape-and-reel suffix | C temperature-grade and tape-and-reel suffix |
主要差異化特點
- Two independent 4:1 sections in one device (對比MAX350CWN)
- Specified channel matching for measurement accuracy (對比MAX350EWN+T)
- Bidirectional low-voltage signal routing (對比MAX350CWN+T)
設計說明
Route the serial clock and data lines away from switched analog inputs and sensitive amplifier inputs. Place the device close to the sources of the signals it selects, maintain a continuous ground plane, and avoid long parallel paths between the multiplexer and receiver. Use the manufacturer’s 18-pin package drawing to confirm pin order, exposed connections, and the orientation of pin 1 before releasing the PCB layout.
Include the switch resistance when calculating signal attenuation. Estimated with a 100 ohm maximum switch resistance and a 10 kilohm receiver input, the maximum resistive divider would attenuate the signal to approximately 99.0 percent of its original value. Actual error also depends on leakage, source impedance, and bandwidth. Evaluate on-resistance matching and the 16 ohm maximum matching specification as separate contributors to channel-to-channel variation.
Bypass each supply connection near the device using the capacitance and placement specified by the manufacturer. The MAX350 family supports dual supplies from ±2.7 V to ±8 V and single-supply operation beginning at +2 V. Confirm the complete allowable supply combinations, logic thresholds, and sequencing requirements before power-up. Use separate, low-impedance return paths for analog and digital currents to reduce supply coupling through the shared ground network.
Do not interpret the family-level product-page starting price as an exact MAX350CWN+ unit price, and do not approve a suffix substitution without reviewing the manufacturer ordering table. The MAX350CWN, MAX350EWN, MAX350EWN+T, and MAX350CWN+T candidates differ in ordering-code meaning even though they retain the same core dual 4:1 architecture and 18-SOIC footprint.
合規資訊
The MAX350 family is identified as production by Analog Devices. A specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for MAX350CWN+ was not identified in the available product information.