MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
料号: MAX350CWN+ ✓ 量产中MAX350CWN+ 概述
A multiplexer is a semiconductor switch that connects one of several inputs to a common output. The 4:1 architecture reduces the number of physical signal connections required in instrumentation, test, measurement, and data-acquisition systems. The MAX350 family combines eight switched signal paths into two serial-controlled 4:1 groups, making it useful when a system must route several low-voltage analog signals while keeping board wiring and control logic compact.
The MAX350CWN+ uses serial control to select the active input path. According to the Analog Devices MAX350 product page, the MAX349 and MAX350 multiplexers conduct equally well in either direction and use CMOS implementations. Their specified dual-supply operating range extends from ±2.7 V to ±8 V. The MAX350CWN+ is identified by the distributor listings as a two-circuit, 4:1, 100 ohm device in an 18-SOIC package.
On-resistance matching is particularly important when several channels carry similar or low-level analog signals. A matched network reduces channel-dependent gain and attenuation errors introduced by the multiplexer. The specified 100 ohm maximum on-resistance also indicates that the device is intended for low-voltage signal-routing applications where substantially lower resistance is generally not required.
Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and industrial control modules. In these systems, the MAX350CWN+ can present one selected signal to a measurement or conversion channel while a microcontroller or test controller operates the serial interface. The dual 4:1 organization allows two multiplexed groups to support paired, differential, or otherwise related signal paths.
PCB implementation requires careful placement of the interface and routed signal nets to limit coupling, crosstalk, and impedance discontinuities. Keep serial-control traces away from sensitive analog paths, use a continuous ground reference, and observe the manufacturer's recommended bypass-capacitor and layout practices. Confirm supply sequencing, logic levels, input-voltage limits, and the exact 18-pin pinout against the manufacturer datasheet before fabrication.
This product record combines the manufacturer product description with distributor package and channel information, then adds practical routing, matching, and selection guidance. It also identifies genuine same-family drop-in candidates while clearly separating verified facts from parameters that require confirmation from the manufacturer datasheet.
直接替换替代料: MAX350CWN+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX350CWN+ (相同外形与封装尺寸) ——差异在于 Number of Channels, Package.
MAX350CWN
✅ 直接替换📋 参考替代料(不在目录中)
MAX350EWN+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX350EWN+T
✅ 直接替换📋 参考替代料(不在目录中)
MAX350CWN+T
✅ 直接替换📋 参考替代料(不在目录中)
MAX350CWN+ 规格参数
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| Number of Channels | 8 channels |
| On-Resistance | 100 ohm maximum |
| On-Resistance Matching | 16 ohm maximum |
| On-Resistance Flatness | 10 ohm maximum over specified signal range |
| Signal Conduction Direction | Bidirectional |
| Control Interface | Serial |
| Dual-Supply Operating Range | ±2.7 V to ±8 V |
| Technology | CMOS |
| 封装 | 18-pin wide SOIC |
| Package Dimensions | 7.50 mm wide |
| 安装类型 | Surface mount |
MAX350CWN+ 7.50 mm wide 引脚配置指南
MAX350CWN+(7.50 mm wide 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX350CWN+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX350CWN+ 适用于 6 应用s: Automated Test Equipment, Data Acquisition Systems, Precision Signal Routing, Industrial Control Modules, Portable Measurement Instruments, Communications and Interface Routing.
Automated Test Equipment
The MAX350CWN+ fits automated test systems that must connect several low-voltage signals to a shared measurement channel. Its dual 4:1 organization provides two independent groups of four switched inputs, reducing the number of external signal connections required at a test fixture. Serial control allows a controller to select paths without dedicating one parallel control line per channel. The 100 ohm maximum on-resistance is suitable when source impedance and measurement accuracy permit that resistance. Engineers should calculate the resulting divider error with the source and input impedances, while the specified 16 ohm maximum switch-to-switch matching helps limit channel-dependent errors.
推荐
Data Acquisition Systems
The MAX350CWN+ can route multiple analog inputs into a shared data-acquisition front end while its serial interface reduces backplane wiring. Two independent 4:1 sections allow related signal groups, such as paired inputs, to be selected with a common controller. Bidirectional conduction is useful when source and destination roles can change. Designers should compare the 100 ohm maximum on-resistance with the selected sensor and converter input impedances, and should assess the 10 ohm maximum on-resistance flatness across the signal range. Decoupling and grounding remain important because the device can operate from dual supplies of ±2.7 V to ±8 V.
推荐
Precision Signal Routing
The MAX350CWN+ is appropriate for multiplexed low-level signal routing where repeatable channel behavior is more important than extremely low resistance. On-resistance is matched between switches to 16 ohm maximum, which limits switch-induced gain differences between channels, while flatness is specified to 10 ohm maximum over the operating signal range. These characteristics help engineers select a channel without introducing large channel-to-channel attenuation changes. The architecture also supports bidirectional routing, allowing the same switch network to be used in measurement and stimulus paths. Source impedance, amplifier input impedance, leakage, and injection error should be evaluated together in the complete signal chain.
推荐
Industrial Control Modules
The MAX350CWN+ can reduce analog-routing complexity in industrial control equipment by connecting several process signals to one controller or measurement channel. Its eight total channels are divided into two 4:1 sections, allowing two related signal groups to be multiplexed within an 18-pin wide SOIC footprint. Serial control supports integration with a microcontroller or test sequencer. For equipment using 24 V field wiring, the MAX350 is not connected directly to that rail; interface circuitry must translate field-level signals to the device’s ±2.7 V to ±8 V dual-supply range or supported single-supply conditions. Production designs should also include protection against transients and verify logic-level compatibility.
推荐
Portable Measurement Instruments
The MAX350CWN+ supports compact handheld or portable measurement instruments where multiple sensors must reach a shared analog front end without a large connector or matrix switch. The serial-control architecture reduces control wiring, while the 18-SOIC package preserves board area. Its bidirectional conduction allows signal paths to be reused for excitation and measurement where the system architecture permits. Designers should include local bypass capacitors, maintain a low-impedance ground plane, and keep serial clock and data traces away from sensitive input nets. Because the switch resistance can reach 100 ohm, error calculations must include sensor impedance and downstream amplifier bias current to prevent gain errors.
推荐
Communications and Interface Routing
The MAX350CWN+ can serve as a low-voltage auxiliary signal router in communications equipment when several control, status, or monitor lines must reach a common interface controller. Its serial selection mechanism limits parallel control overhead, and the bidirectional CMOS switches accommodate varied routing directions. The MAX350 is intended for low-voltage multiplexing rather than high-impedance RF distribution, so engineers should verify bandwidth, capacitance, and insertion-loss behavior against the manufacturer data. Keep the serial bus away from high-energy clock and power paths, use a continuous reference plane, and place supply bypass capacitors close to the device. Firmware should avoid changing routes during sensitive conversions unless the system timing permits the resulting transient.
推荐
推荐产品汇总
工程参考数据: MAX350CWN+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX350CWN | MAX350EWN | MAX350EWN+T | MAX350CWN+T |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 18-SOIC | 18-SOIC | 18-SOIC | 18-SOIC | 18-SOIC |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Total Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Maximum On-Resistance | 100 ohm | 100 ohm | 100 ohm | 100 ohm | 100 ohm |
| Control Interface | Serial | Serial | Serial | Serial | Serial |
| Dual-Supply Operating Range | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V | ±2.7 V to ±8 V |
| Signal Conduction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Ordering-Suffix Difference | CWN+ enhanced ordering form | CWN without plus suffix | E temperature-grade suffix | E temperature-grade and tape-and-reel suffix | C temperature-grade and tape-and-reel suffix |
关键差异点
- Two independent 4:1 sections in one device (对比 MAX350CWN)
- Specified channel matching for measurement accuracy (对比 MAX350EWN+T)
- Bidirectional low-voltage signal routing (对比 MAX350CWN+T)
设计说明
Route the serial clock and data lines away from switched analog inputs and sensitive amplifier inputs. Place the device close to the sources of the signals it selects, maintain a continuous ground plane, and avoid long parallel paths between the multiplexer and receiver. Use the manufacturer’s 18-pin package drawing to confirm pin order, exposed connections, and the orientation of pin 1 before releasing the PCB layout.
Include the switch resistance when calculating signal attenuation. Estimated with a 100 ohm maximum switch resistance and a 10 kilohm receiver input, the maximum resistive divider would attenuate the signal to approximately 99.0 percent of its original value. Actual error also depends on leakage, source impedance, and bandwidth. Evaluate on-resistance matching and the 16 ohm maximum matching specification as separate contributors to channel-to-channel variation.
Bypass each supply connection near the device using the capacitance and placement specified by the manufacturer. The MAX350 family supports dual supplies from ±2.7 V to ±8 V and single-supply operation beginning at +2 V. Confirm the complete allowable supply combinations, logic thresholds, and sequencing requirements before power-up. Use separate, low-impedance return paths for analog and digital currents to reduce supply coupling through the shared ground network.
Do not interpret the family-level product-page starting price as an exact MAX350CWN+ unit price, and do not approve a suffix substitution without reviewing the manufacturer ordering table. The MAX350CWN, MAX350EWN, MAX350EWN+T, and MAX350CWN+T candidates differ in ordering-code meaning even though they retain the same core dual 4:1 architecture and 18-SOIC footprint.
合规信息
The MAX350 family is identified as production by Analog Devices. A specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for MAX350CWN+ was not identified in the available product information.