MKE06Z64VLD4 - 48MHz 64KB Flash Cortex-M0+ MCU | NXP
Teilenummer: MKE06Z64VLD4 ✓ AktivMKE06Z64VLD4 Übersicht
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The MKE06Z64VLD4 belongs to the Kinetis E series, where the Cortex-M0+ core provides a compact, energy-efficient architecture for control-oriented tasks. This device hierarchy connects the ARM Cortex-M0+ processor, 32-bit microcontroller, embedded controller, and semiconductor categories within a single integrated component.
Key features include a 48 MHz Cortex-M0+ core, 64 KB of Flash program memory, 8 KB of SRAM, and integrated 6-bit and 12-bit ADC channels. Its 5 V robust design emphasizes enhanced ESD and EMC performance for high-reliability products used in electrically noisy environments. An integrated low-voltage detector and power-on reset module supports reliable startup and supply monitoring.
The 44-LQFP package provides a conventional leaded surface-mount footprint that is inspectable after assembly and appropriate for prototypes, industrial controllers, and cost-sensitive production boards. The device combines a 2.7 V to 5.5 V operating range with 64 KB of embedded Flash, avoiding an external memory interface for many control applications while retaining sufficient SRAM for protocol handling, acquisition, and supervisory logic.
Typical applications include industrial control panels, appliance controllers, building equipment, automotive accessories, sensor nodes, and compact embedded systems. The ADC resources support analog measurement, while the Cortex-M0+ instruction set and integrated memories are suited to real-time monitoring, state-machine control, communications, and actuator supervision where deterministic peripheral behavior and low system complexity matter.
PCB design should preserve clean supply distribution because high-current return paths can disturb sensitive ADC measurements. Place the decoupling capacitor close to the supply pins, route analog inputs away from switching nodes, and connect all ground pins according to the manufacturer pin and layout guidance. Firmware should also exercise reset and low-voltage conditions because the integrated LVD/POR circuitry does not replace application-level validation of brownout behavior.
This product page combines NXP device information with package, memory, application, sourcing, and replacement guidance for engineers evaluating the MKE06Z64VLD4. It also highlights the limits of direct substitution: a same-package candidate must match the critical clock, memory, voltage, peripheral, and pin-level requirements rather than relying on package similarity alone.
Drop-in-Alternativen für MKE06Z64VLD4 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MKE06Z64VLD4 (gleiche Bauform und Footprint) – abweichend in Operating Voltage.
MKE06Z64VLH4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MKE06Z64VLD4 Grenzwerte & elektrische Eigenschaften
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Product Series | Kinetis KE06 |
| Maximale Taktfrequenz | 48 MHz |
| CPU Core | ARM Cortex-M0+ |
| Flash Memory | 64 KB |
| SRAM | 8 KB |
| Operating Voltage | 2.7 V to 5.5 V |
| ADC Resolution | 6-bit and 12-bit |
| Gehäuse | 44-LQFP, 10 x 10 mm |
| Montageart | Surface mount |
| Supply Type | 5 V robust |
| ESD and EMC Features | Enhanced ESD/EMC performance |
| Voltage Monitoring | Integrated LVD/POR module |
| Packaging | Tray |
| RoHS-Status | Compliant |
| Moisture Sensitivity Level | MSL 3 |
| REACH Status | Unspecified |
MKE06Z64VLD4 44-lqfp, 10 x 10 mm Pinbelegungsleitfaden
Pinbelegung für MKE06Z64VLD4 (44-lqfp, 10 x 10 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für MKE06Z64VLD4.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MKE06Z64VLD4 ist geeignet für 6 Anwendungs: Industrial Control Module, Automotive Accessory Controller, Appliance Controller, Building Equipment Interface, Sensor and Measurement Node, Robust IoT Control Node.
Industrial Control Module
The MKE06Z64VLD4 fits industrial control modules that combine 2.7 V to 5.5 V operation with a 48 MHz Cortex-M0+ core, 64 KB Flash, and 8 KB SRAM. Its 5 V robust construction and enhanced ESD/EMC characteristics are useful when the controller operates near relays, contactors, motor drivers, or other electrically noisy equipment. The MCU can supervise inputs, sequence actuators, and manage local communications without external program memory. Validate grounding and surge requirements at the board level, and review the exact temperature and qualification grade before using the device in a deployed industrial enclosure.
Empfohlen
Automotive Accessory Controller
The MKE06Z64VLD4 is suitable for compact automotive accessory controllers where a 48 MHz Cortex-M0+ processor, 64 KB Flash, and 8 KB SRAM provide enough capability for switch monitoring, diagnostics, and actuator sequencing. Its integrated LVD/POR module supports dependable initialization, while the 5 V robust design targets high-reliability equipment in electrically noisy environments. The 44-LQFP package also permits visual inspection after board assembly. Automotive production approval depends on confirming the exact qualification, temperature rating, change-notice status, and manufacturer-approved operating conditions.
Empfohlen
Appliance Controller
The MKE06Z64VLD4 can serve as the central controller in an appliance because its 48 MHz processing speed supports real-time state management while 64 KB Flash and 8 KB SRAM accommodate embedded control firmware. The 2.7 V to 5.5 V supply range is convenient for mixed 3.3 V and 5 V system architectures, and the 12-bit ADC channel can measure analog inputs such as temperature or load signals. A designer should place the supply bypass capacitor correctly, isolate ADC routing from motor and heater switching paths, and confirm that all peripheral timing is compatible with the selected clock configuration.
Empfohlen
Building Equipment Interface
The MKE06Z64VLD4 fits building equipment interfaces that monitor switches, sensors, and remote modules while maintaining a compact 44-LQFP footprint. Its 64 KB Flash provides room for protocol and supervisory routines, and the 8 KB SRAM supports buffering or state management without requiring a separate memory device. The integrated LVD/POR circuitry assists startup reliability in systems where the supply can fluctuate. For long cable runs or high-energy loads, apply the manufacturer's ESD/EMC layout practices and use appropriate external protection rather than relying on the MCU alone.
Empfohlen
Sensor and Measurement Node
The MKE06Z64VLD4 is appropriate for compact sensor nodes that acquire analog measurements and perform local filtering, thresholding, or diagnostics. Its ADC supports 6-bit and 12-bit conversion, while the 48 MHz Cortex-M0+ core can service multiple acquisition and communication routines within limited memory. The 2.7 V minimum operating voltage supports low-voltage designs, although the complete node must remain within 2.7 V to 5.5 V. Keep sensitive analog traces short and away from switching nodes, follow the reference layout, and confirm the required sampling rate and source impedance.
Empfohlen
Robust IoT Control Node
The MKE06Z64VLD4 supports compact IoT control nodes that must acquire data, execute local logic, and manage communication under a 5 V robust power environment. Its 64 KB Flash accommodates networking and update-related code, while 8 KB SRAM provides working memory for protocol handling. The enhanced ESD/EMC characteristics are particularly relevant to nodes installed near motors, relays, or poorly controlled external wiring. Designers should isolate field-facing connectors, provide appropriate surge protection, preserve continuous ground paths, and verify firmware behavior across reset and low-voltage conditions.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MKE06Z64VLD4 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MKE06Z64VLH4 |
|---|---|---|
| Package | 44-LQFP, 10 x 10 mm | 44-LQFP |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Product Series | Kinetis KE06 | Kinetis KE06 |
| CPU Core | ARM Cortex-M0+ | ARM Cortex-M0+ |
Wichtigste Unterscheidungsmerkmale
- 48 MHz processing performance in the KE06 family (vs. MKE06Z64VLH4)
- Integrated memory for self-contained control designs (vs. MKE06Z64VLH4)
- Robust electrical design for noisy environments (vs. MKE06Z64VLH4)
Designhinweise
Place the required bypass capacitor as close as practical to the MKE06Z64VLD4 supply pins and provide an uninterrupted ground return. Route high-current loads and switching-regulator connections away from the MCU. The 2.7 V to 5.5 V operating range does not eliminate the need for clean local supply distribution, particularly when ADC measurements and reset behavior must remain reliable.
Separate analog inputs from digital and switching traces, keep analog traces short, and connect the analog ground reference according to the manufacturer layout diagram. Because the device includes 6-bit and 12-bit ADC channels, source impedance, acquisition time, and routing can influence measurement accuracy. Test the completed layout across the intended supply range rather than relying only on nominal simulation conditions.
Do not substitute a related KE04, KE02, or alternate ordering code solely because it uses a similar 44-LQFP package. The KE06 target runs at 48 MHz and includes 64 KB Flash, while lower family members have different timing and resource characteristics. Review the manufacturer pin table, clock setup, peripheral mapping, memory organization, temperature grade, and qualification before treating any alternative as a drop-in replacement.
Compliance-Informationen
RoHS compliance and MSL 3 are reported for the exact MPN. REACH status is not confirmed. Automotive application suitability does not by itself establish AEC-Q100 qualification for this ordering code.