MSP430F2013IPW - 16MHz Low-Power MCU | Texas Instruments
Teilenummer: MSP430F2013IPW ✓ AktivMSP430F2013IPW Übersicht
An ultra-low-power mixed-signal microcontroller is a semiconductor device designed to execute embedded control and measurement tasks while consuming very little energy. The MSP430 platform combines a 16-bit RISC processor, analog sensing capability, timers, communication peripherals, and GPIO in one compact component. Its architecture belongs to the microcontroller and embedded-processing hierarchy, making it especially useful for battery-operated instruments, industrial sensors, and compact control systems.
The MSP430F2013IPW combines a 16 MHz CPU16 core with 2 KB Flash and 128 bytes of RAM. Its mixed-signal resources include a 16-bit sigma-delta ADC and a versatile analog comparator. The Universal Serial Interface provides synchronous serial communication through SPI or I2C, while the built-in timer supports periodic measurement and control tasks. Ten I/O pins give the device enough external connectivity for compact sensor nodes and embedded control boards.
The MSP430 CPU16 uses 16-bit registers and a RISC instruction set optimized for low-power operation. The sigma-delta ADC is intended for measurement paths where resolution and noise performance matter more than conversion speed. Because the MCU combines digital processing and analog measurement, it can reduce external component count in sensing products. Firmware can configure the USI for either SPI or I2C according to the peripheral ecosystem and board-level requirements.
Typical uses include portable environmental monitors, industrial measurement instruments, low-power sensor interfaces, compact data-acquisition nodes, and embedded control products. The 14-pin TSSOP package is useful where a small PCB footprint is required. The MSP-TS430PW14 target board supports programming and debugging for MSP430F2x and MSP430G2x devices using JTAG or Spy-Bi-Wire, making it a practical development platform for initial firmware bring-up.
When laying out a design, reserve the decoupling and programming interface pins required by the device, keep sensitive analog routing away from fast digital switching, and validate the ADC input network against the measurement bandwidth. Program conversion and communication behavior through the USI and confirm the required clock, reset, and debugger connections against the manufacturer pin-description table before releasing the PCB.
This page combines manufacturer specifications, sourcing guidance, application analysis, and engineering design notes to support MCU selection and board development. It also highlights the importance of checking memory requirements, peripheral compatibility, and package-level pin assignments before committing MSP430F2013IPW to a production design.
Drop-in-Alternativen für MSP430F2013IPW – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MSP430F2013IPW (gleiche Bauform und Footprint) – abweichend in ADC Resolution, CPU Architecture, Package, Operating Temperature Range, Supply Voltage.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernMSP430F2013IPW Grenzwerte & elektrische Eigenschaften
| CPU Architecture | MSP430 CPU16 16-bit RISC |
| Maximale Taktfrequenz | 16 MHz |
| Flash Memory | 2 KB |
| RAM | 128 bytes |
| ADC Type | 16-bit sigma-delta ADC |
| ADC Quantity | 1 |
| Serial Interface | USI supporting SPI and I2C |
| Analog Comparator | 1 |
| General-Purpose I/O | 10 pins |
| Timer | 16-bit |
| Gehäuse | 14-pin TSSOP |
| Montageart | Surface mount |
| Operating Temperature Grade | Industrial |
MSP430F2013IPW 14-pin tssop Pinbelegungsleitfaden
Pinbelegung für MSP430F2013IPW (14-pin tssop-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für MSP430F2013IPW.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MSP430F2013IPW ist geeignet für 6 Anwendungs: Portable Environmental Sensor, Industrial Process Measurement, Compact Data Acquisition Node, Battery-Powered Meter, SPI Sensor Interface, Programmable Threshold Controller.
Portable Environmental Sensor
The MSP430F2013IPW is well suited to a battery-powered environmental sensor because it combines a 16 MHz MSP430 CPU16 core with a 16-bit sigma-delta ADC in one 14-pin TSSOP device. The ADC can acquire low-bandwidth analog measurements while the microcontroller performs filtering, threshold evaluation, and sensor compensation. Its 2 KB Flash and 128 bytes of RAM support compact control firmware rather than demanding high-compute workloads. A practical design can configure the USI for I2C or SPI to connect a digital temperature, humidity, or gas sensor. Power consumption depends on the selected clock, ADC conversion schedule, communication rate, and duty cycle, so battery sizing should use the complete firmware operating profile.
Empfohlen
Industrial Process Measurement
MSP430F2013IPW can serve as the controller for a compact industrial process-measurement node when the signal requires moderate resolution rather than high-rate conversion. Its 16-bit sigma-delta ADC is suited to slowly changing process variables, while the built-in comparator can support threshold detection and supervisory functions. The 16-bit timer provides a basis for periodic sampling and control timing, and the USI can communicate with remote sensor or actuator electronics through I2C or SPI. Industrial designs should verify the operating-temperature grade, isolation requirements, input protection, and analog accuracy at the intended supply voltage. Firmware can also compensate sensor offset and gain, detect open inputs, and transmit processed measurements over the selected serial interface.
Empfohlen
Compact Data Acquisition Node
The MSP430F2013IPW is appropriate for a low-channel-count data-acquisition node that must acquire, filter, and forward analog measurements without a large application processor. Its 16-bit sigma-delta ADC supports measurement of slow or band-limited signals, while the CPU16 core can apply calibration, digital filtering, and units conversion within the available 2 KB of Flash. The USI provides a practical path to a local display, external memory, or host processor through I2C or SPI. Because RAM is limited to 128 bytes, the firmware should use a streaming data model and avoid retaining large sample buffers. The 14-pin TSSOP package also helps reduce board area, although analog layout should preserve a clean return path and minimize coupling between sensor inputs and digital communication lines.
Empfohlen
Battery-Powered Meter
MSP430F2013IPW fits a battery-powered meter that combines analog measurement with a compact serial interface. The 16-bit sigma-delta ADC can measure a conditioned sensor signal, while the MSP430 CPU16 core performs scaling, calibration, and limit checks. The USI can drive a display driver, data logger, or external radio through I2C or SPI, and the 128-byte RAM supports short working buffers and stack operations. Because the available Flash is limited to 2 KB, complex user interfaces and extensive data storage are better assigned to external components. Design work should focus on sleep-state behavior, startup-time requirements, reference accuracy, and the analog front end. Use the manufacturer ADC and electrical-characteristic sections to establish timing and accuracy limits.
Empfohlen
SPI Sensor Interface
The MSP430F2013IPW is suitable for a compact SPI sensor interface because its Universal Serial Interface supports synchronous SPI communication. The 16 MHz CPU16 core provides enough processing capability to configure the sensor, collect measurements, perform basic filtering, and forward results over another serial link. Its 16-bit sigma-delta ADC can monitor an auxiliary analog channel or supply a threshold input, and the built-in comparator supports simple event detection. SPI clocking, chip-select handling, and sensor timing should be implemented against the peripheral and device data requirements. Board layout should keep clock and data traces short, provide a defined return path, and account for signal-integrity behavior at the intended clock rate. Firmware validation should cover startup delay, conversion timing, and sensor fault handling.
Empfohlen
Programmable Threshold Controller
MSP430F2013IPW can implement a programmable threshold controller for industrial or instrumentation systems that require local analog decision-making. The integrated analog comparator can observe a reference or sensor signal, while the 16-bit sigma-delta ADC provides a higher-resolution measurement path when the application needs calibrated readings. The 16-bit timer can establish measurement intervals or output timing, and the USI can report state changes to a supervisory controller. The device’s 2 KB Flash and 128 bytes of RAM favor a focused firmware structure with compact calibration tables. Designers should evaluate comparator and ADC input ranges, noise behavior, threshold stability, and output timing before fixing the control architecture. A development board such as MSP-TS430PW14 can support firmware bring-up and peripheral validation before the embedded design is finalized.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MSP430F2013IPW – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Brand | Texas Instruments |
| Package | 14-pin TSSOP |
| CPU Architecture | 16-bit MSP430 CPU16 RISC |
| Maximum Clock Frequency | 16 MHz |
| Flash Memory | 2 KB |
| RAM | 128 bytes |
| ADC | One 16-bit sigma-delta ADC |
| Serial Interface | USI supporting SPI and I2C |
| General-Purpose I/O | 10 pins |
| Temperature Grade | Industrial |
Wichtigste Unterscheidungsmerkmale
- Integrated high-resolution sigma-delta conversion (vs. Higher-memory MSP430 variants)
- Compact mixed-signal integration (vs. External ADC implementations)
- Protocol-flexible serial communications (vs. Serial-interface-free microcontroller variants)
Designhinweise
Confirm the complete power-consumption profile with the manufacturer electrical characteristics before selecting the supply and battery. The MSP430F2013IPW has a 16 MHz clock rating, but real operating current depends on the active clock, ADC conversion schedule, USI activity, GPIO state, and whether the CPU is running or placed into a low-power state. Use the datasheet current figures for each operating mode and avoid leaving unused inputs floating. Decoupling and supply sequencing must follow the power-pin requirements shown in the manufacturer pin-description and application guidance.
Keep analog sensor traces short and isolate them from clock, USI, and other switching paths. The sigma-delta ADC is intended for measurement of suitable bandwidth-limited signals, so a slow signal does not justify a long high-impedance route through electrically noisy PCB areas. Use a continuous ground reference, place input components near the ADC source, and keep return-current paths direct. Validate the final input filter against both the desired measurement bandwidth and the ADC acquisition requirements before releasing the layout.
Do not select MSP430F2013IPW solely from its 16 MHz clock rating. Confirm that 2 KB of Flash and 128 bytes of RAM accommodate the application code, stack, constants, and communication buffers. Also verify that one ADC, ten I/O pins, and the USI satisfy the interface plan. During programming, connect the target correctly to a supported JTAG or Spy-Bi-Wire setup and use the manufacturer pin-description table for test, reset, power, ground, and GPIO assignments.
For a SPI sensor design, calculate the communication duty cycle from the transaction rate, bus width, and required settling time. The USI supports SPI or I2C, but the selected protocol, slave address strategy, pull resistors, and maximum clock determine the implementation. Keep the sensor and MCU rails local to the relevant circuitry, provide the required bypass capacitance close to the device, and verify the ADC reference relationship if analog and digital measurements are correlated.
Compliance-Informationen
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated for this orderable code. AEC-Q100 is not applicable because MSP430F2013IPW is an industrial mixed-signal microcontroller rather than an automotive-qualified device.