Texas Instruments

MSP430F2013IPW - 16MHz Low-Power MCU | Texas Instruments

MPN: MSP430F2013IPW ✓ فعال
14-pin TSSOP Package 16 MHz Speed 2 KB Memory
MOQ: 1 |

MSP430F2013IPW جائزہ

Texas Instruments MSP430F2013IPW is a 16-bit ultra-low-power mixed-signal microcontroller operating at up to 16 MHz, with 2 KB of Flash memory, 128 bytes of RAM, one 16-bit sigma-delta ADC, and USI support for SPI or I2C communication in a 14-pin TSSOP package.

An ultra-low-power mixed-signal microcontroller is a semiconductor device designed to execute embedded control and measurement tasks while consuming very little energy. The MSP430 platform combines a 16-bit RISC processor, analog sensing capability, timers, communication peripherals, and GPIO in one compact component. Its architecture belongs to the microcontroller and embedded-processing hierarchy, making it especially useful for battery-operated instruments, industrial sensors, and compact control systems.

The MSP430F2013IPW combines a 16 MHz CPU16 core with 2 KB Flash and 128 bytes of RAM. Its mixed-signal resources include a 16-bit sigma-delta ADC and a versatile analog comparator. The Universal Serial Interface provides synchronous serial communication through SPI or I2C, while the built-in timer supports periodic measurement and control tasks. Ten I/O pins give the device enough external connectivity for compact sensor nodes and embedded control boards.

The MSP430 CPU16 uses 16-bit registers and a RISC instruction set optimized for low-power operation. The sigma-delta ADC is intended for measurement paths where resolution and noise performance matter more than conversion speed. Because the MCU combines digital processing and analog measurement, it can reduce external component count in sensing products. Firmware can configure the USI for either SPI or I2C according to the peripheral ecosystem and board-level requirements.

Typical uses include portable environmental monitors, industrial measurement instruments, low-power sensor interfaces, compact data-acquisition nodes, and embedded control products. The 14-pin TSSOP package is useful where a small PCB footprint is required. The MSP-TS430PW14 target board supports programming and debugging for MSP430F2x and MSP430G2x devices using JTAG or Spy-Bi-Wire, making it a practical development platform for initial firmware bring-up.

When laying out a design, reserve the decoupling and programming interface pins required by the device, keep sensitive analog routing away from fast digital switching, and validate the ADC input network against the measurement bandwidth. Program conversion and communication behavior through the USI and confirm the required clock, reset, and debugger connections against the manufacturer pin-description table before releasing the PCB.

This page combines manufacturer specifications, sourcing guidance, application analysis, and engineering design notes to support MCU selection and board development. It also highlights the importance of checking memory requirements, peripheral compatibility, and package-level pin assignments before committing MSP430F2013IPW to a production design.

کے لیے ڈراپ اِن متبادل MSP430F2013IPW — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MSP430F2013IPW (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف ADC Resolution, CPU Architecture, Package, Operating Temperature Range, Supply Voltage.

Texas Instruments
ADC Resolution: 10 bit
CPU Architecture: 16-bit RISC
موازنہ کریں MSP430F2013IPW →
Texas Instruments
ADC Resolution: 16-bit sigma-delta
CPU Architecture: 16-bit RISC
Package: 14-pin TSSOP (PW)
موازنہ کریں MSP430F2013IPW →
Texas Instruments
CPU Architecture: MSP430 16-bit RISC
Package: 14-TSSOP
Operating Temperature Range: -40 °C to +85 °C
موازنہ کریں MSP430F2013IPW →
Texas Instruments
ADC Resolution: 10 bits
CPU Architecture: 16-bit RISC
Package: 14-pin TSSOP (PW)
موازنہ کریں MSP430F2013IPW →
Texas Instruments
ADC Resolution: 10-bit
CPU Architecture: 16-bit RISC
Operating Temperature Range: -40°C to +105°C
موازنہ کریں MSP430F2013IPW →
Texas Instruments
ADC Resolution: 16 bit
CPU Architecture: MSP430 CPU16, 16-bit RISC
Package: 14-pin TSSOP (PW)
موازنہ کریں MSP430F2013IPW →

اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔

متبادل کی درخواست کریں

MSP430F2013IPW زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

CPU Architecture MSP430 CPU16 16-bit RISC
زیادہ سے زیادہ کلاک فریکوئنسی 16 MHz
Flash Memory 2 KB
RAM 128 bytes
ADC Type 16-bit sigma-delta ADC
ADC Quantity 1
Serial Interface USI supporting SPI and I2C
Analog Comparator 1
General-Purpose I/O 10 pins
Timer 16-bit
پیکیج 14-pin TSSOP
ماؤنٹنگ ٹائپ Surface mount
Operating Temperature Grade Industrial

MSP430F2013IPW 14-pin tssop پن کنفیگریشن گائیڈ

MSP430F2013IPW (14-pin tssop پیکیج) کے لیے پن کنفیگریشن۔ اس ڈیجیٹل IC میں GPIO، کمیونیکیشن انٹرفیس (UART، SPI، I2C) اور پاور پنز شامل ہیں۔ متبادل پن فنکشنز اور کنفیگریشن آپشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ ایمبیڈڈ سسٹم ڈیزائن اور PCB لے آؤٹ کے لیے ضروری۔

MSP430F2013IPW کے لیے 14-pin tssop پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MSP430F2013IPW.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

MSP430F2013IPW کے لیے موزوں ہے 6 ایپلیکیشنs: Portable Environmental Sensor, Industrial Process Measurement, Compact Data Acquisition Node, Battery-Powered Meter, SPI Sensor Interface, Programmable Threshold Controller.

🧩

Portable Environmental Sensor

The MSP430F2013IPW is well suited to a battery-powered environmental sensor because it combines a 16 MHz MSP430 CPU16 core with a 16-bit sigma-delta ADC in one 14-pin TSSOP device. The ADC can acquire low-bandwidth analog measurements while the microcontroller performs filtering, threshold evaluation, and sensor compensation. Its 2 KB Flash and 128 bytes of RAM support compact control firmware rather than demanding high-compute workloads. A practical design can configure the USI for I2C or SPI to connect a digital temperature, humidity, or gas sensor. Power consumption depends on the selected clock, ADC conversion schedule, communication rate, and duty cycle, so battery sizing should use the complete firmware operating profile.

🏭

Industrial Process Measurement

MSP430F2013IPW can serve as the controller for a compact industrial process-measurement node when the signal requires moderate resolution rather than high-rate conversion. Its 16-bit sigma-delta ADC is suited to slowly changing process variables, while the built-in comparator can support threshold detection and supervisory functions. The 16-bit timer provides a basis for periodic sampling and control timing, and the USI can communicate with remote sensor or actuator electronics through I2C or SPI. Industrial designs should verify the operating-temperature grade, isolation requirements, input protection, and analog accuracy at the intended supply voltage. Firmware can also compensate sensor offset and gain, detect open inputs, and transmit processed measurements over the selected serial interface.

📊

Compact Data Acquisition Node

The MSP430F2013IPW is appropriate for a low-channel-count data-acquisition node that must acquire, filter, and forward analog measurements without a large application processor. Its 16-bit sigma-delta ADC supports measurement of slow or band-limited signals, while the CPU16 core can apply calibration, digital filtering, and units conversion within the available 2 KB of Flash. The USI provides a practical path to a local display, external memory, or host processor through I2C or SPI. Because RAM is limited to 128 bytes, the firmware should use a streaming data model and avoid retaining large sample buffers. The 14-pin TSSOP package also helps reduce board area, although analog layout should preserve a clean return path and minimize coupling between sensor inputs and digital communication lines.

⚡

Battery-Powered Meter

MSP430F2013IPW fits a battery-powered meter that combines analog measurement with a compact serial interface. The 16-bit sigma-delta ADC can measure a conditioned sensor signal, while the MSP430 CPU16 core performs scaling, calibration, and limit checks. The USI can drive a display driver, data logger, or external radio through I2C or SPI, and the 128-byte RAM supports short working buffers and stack operations. Because the available Flash is limited to 2 KB, complex user interfaces and extensive data storage are better assigned to external components. Design work should focus on sleep-state behavior, startup-time requirements, reference accuracy, and the analog front end. Use the manufacturer ADC and electrical-characteristic sections to establish timing and accuracy limits.

🔧

SPI Sensor Interface

The MSP430F2013IPW is suitable for a compact SPI sensor interface because its Universal Serial Interface supports synchronous SPI communication. The 16 MHz CPU16 core provides enough processing capability to configure the sensor, collect measurements, perform basic filtering, and forward results over another serial link. Its 16-bit sigma-delta ADC can monitor an auxiliary analog channel or supply a threshold input, and the built-in comparator supports simple event detection. SPI clocking, chip-select handling, and sensor timing should be implemented against the peripheral and device data requirements. Board layout should keep clock and data traces short, provide a defined return path, and account for signal-integrity behavior at the intended clock rate. Firmware validation should cover startup delay, conversion timing, and sensor fault handling.

🖥️

Programmable Threshold Controller

MSP430F2013IPW can implement a programmable threshold controller for industrial or instrumentation systems that require local analog decision-making. The integrated analog comparator can observe a reference or sensor signal, while the 16-bit sigma-delta ADC provides a higher-resolution measurement path when the application needs calibrated readings. The 16-bit timer can establish measurement intervals or output timing, and the USI can report state changes to a supervisory controller. The device’s 2 KB Flash and 128 bytes of RAM favor a focused firmware structure with compact calibration tables. Designers should evaluate comparator and ADC input ranges, noise behavior, threshold stability, and output timing before fixing the control architecture. A development board such as MSP-TS430PW14 can support firmware bring-up and peripheral validation before the embedded design is finalized.

تجویز کردہ پروڈکٹس کا خلاصہ

MSP-TS430PW14 Programming and debug target board استعمال ہوتا ہے: Portable Environmental Sensor, Industrial Process Measurement, Compact Data Acquisition Node, Battery-Powered Meter, SPI Sensor Interface, Programmable Threshold Controller MSP430F2013 Base device family استعمال ہوتا ہے: Portable Environmental Sensor, Industrial Process Measurement, Compact Data Acquisition Node, Battery-Powered Meter, SPI Sensor Interface, Programmable Threshold Controller
What is the operating frequency of MSP430F2013IPW?
The MSP430F2013IPW operates at up to 16 MHz and uses a 16-bit MSP430 CPU16 RISC core. According to the Texas Instruments MSP430F20x1, MSP430F20x2, and MSP430F20x3 mixed-signal microcontroller datasheet, this processing capability supports efficient embedded control and measurement while retaining the low-power characteristics of the MSP430 family. The device is intended for designs where responsive control logic and compact memory are needed without a high-performance application processor.
How much Flash and RAM does MSP430F2013IPW have?
The MSP430F2013IPW provides 2 KB of Flash memory and 128 bytes of RAM. The Texas Instruments product page identifies the device as a 16 MHz sensing MCU with 2 KB Flash and 128 bytes of RAM. This memory footprint is suitable for compact control firmware, sensor configuration, calibration constants, and communication routines, but designers should check application size, bootloader requirements, and stack usage before finalizing the firmware architecture.
What peripherals are integrated in MSP430F2013IPW?
The MSP430F2013IPW integrates one 16-bit sigma-delta ADC, one analog comparator, a 16-bit timer, ten I/O pins, and a Universal Serial Interface supporting SPI or I2C. The manufacturer datasheet identifies the ADC and USI as central mixed-signal resources. Together, they allow the MCU to acquire analog measurements, compare threshold levels, control external timing, and communicate with sensors or peripherals without requiring separate interface ICs.
Is MSP430F2013IPW suitable for low-power sensor applications?
Yes, the MSP430F2013IPW is suitable for low-power sensor applications because it combines a 16-bit MSP430 CPU16 core, a 16-bit sigma-delta ADC, and 128 bytes of RAM in a compact device. The Texas Instruments manufacturer datasheet describes the MSP430F20xx family as an ultra-low-power mixed-signal microcontroller family. Final battery-life calculations should include the configured clock, ADC sampling rate, USI activity, duty cycle, and peripheral sleep states used by the finished product.
What is the difference between MSP430F2013IPW and MSP430F2013IPWR?
MSP430F2013IPW and MSP430F2013IPWR identify the same MSP430F2013 device and 14-pin TSSOP electrical configuration, while the final orderable suffix generally distinguishes the shipping format. The search comparison identifies MSP430F2013IPWR as the comparable reel-form ordering variant of MSP430F2013IPW. Because packing-code differences add little circuit-level value, engineers should compare memory, ADC, clock, USI, temperature grade, and pin assignments when evaluating interchangeability.
When should I choose MSP430F2013IPW over a higher-memory MSP430?
Choose MSP430F2013IPW when the application fits within 2 KB of Flash and 128 bytes of RAM while requiring a 16 MHz CPU, a 16-bit sigma-delta ADC, SPI or I2C through the USI, and only ten general-purpose I/O pins. Select a higher-memory MSP430 when firmware, communication buffers, logging, calibration tables, or application complexity exceed those limits. The MSP430F2013IPW is strongest in compact measurement and control designs with tightly scoped firmware.
Is MSP430F2013IPW suitable for SPI and I2C sensor designs?
The MSP430F2013IPW is suitable for both SPI and I2C sensor designs because its Universal Serial Interface supports these synchronous serial protocols. According to the Texas Instruments mixed-signal microcontroller datasheet, the F20x3 family adds communication capability using SPI or I2C. The protocol choice should account for clock rate, slave addressing, bus topology, pull-up requirements, and the peripheral’s specific timing characteristics.
Where can I download the MSP430F2013IPW datasheet PDF?
The official MSP430F2013 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/gpn/MSP430F2013, and the product support page is located at https://www.ti.com/product/MSP430F2013. The datasheet contains the authoritative pin descriptions, electrical characteristics, ADC information, timing details, and ordering information. Use the pin-description table when assigning PCB nets and confirm the device revision and orderable suffix before production release.
Where can I find the MSP430F2013IPW pinout?
The MSP430F2013IPW pinout is published in the pin-description section of the Texas Instruments MSP430F20x1, MSP430F20x2, and MSP430F20x3 mixed-signal microcontroller datasheet. The device uses a 14-pin TSSOP package. Because a complete pin list is not reproduced on this page, use the manufacturer diagram to verify power, ground, reset, test, clock, analog, and GPIO assignments before routing the PCB.
What can replace MSP430F2013IPW?
A drop-in replacement should preserve the MSP430F2013 core, 2 KB Flash, 128-byte RAM, 16-bit sigma-delta ADC, USI configuration, 16 MHz clock capability, 14-pin TSSOP footprint, and pin assignments. MSP430F2013IPWR is the closest documented orderable variant, differing primarily in packing format. Firmware, timing, ADC behavior, and exposed-debug requirements should still be reviewed before treating any alternate orderable code as interchangeable.
Is MSP430F2013IPW the same as MSP430F2013IPWR?
MSP430F2013IPW and MSP430F2013IPWR are electrically the same MSP430F2013 configuration in a 14-pin TSSOP package, with the alternate suffix primarily identifying a different shipping format. Both retain the 16 MHz 16-bit core, 2 KB Flash, 128-byte RAM, sigma-delta ADC, and USI communication resources. Production programmers and assemblers must match the required mechanical packing format even when the electrical substitution would appear direct.
What are the key specifications of MSP430F2013IPW that engineers should know?
The key specifications are a 16 MHz MSP430 CPU16 core, 2 KB Flash, 128 bytes of RAM, one 16-bit sigma-delta ADC, one analog comparator, a 16-bit timer, ten I/O pins, and USI support for SPI and I2C. Texas Instruments packages the device in a 14-pin TSSOP. These figures define its suitability for compact, low-power embedded measurement and control designs rather than high-compute or large-memory applications.
How do I program MSP430F2013IPW?
MSP430F2013IPW can be programmed through the device’s supported debugging interface using JTAG or the two-wire Spy-Bi-Wire protocol. Texas Instruments identifies the MSP-TS430PW14 as a standalone ZIF-socket target board for programming and debugging MSP430F2x and MSP430G2x devices. During board bring-up, connect the debugger to the appropriate test and reset signals, verify target power, and follow the developer documentation for the selected debugger and firmware toolchain.
Where can I buy MSP430F2013IPW online?
Use the Request a Quote form on this page to request MSP430F2013IPW availability, current unit pricing, minimum order quantity, and lead time. The form supports direct procurement review without relying on stale marketplace figures. Confirm the requested package, industrial temperature grade, tube or reel logistics, and programming or marking requirements when submitting the request.
What is the price of MSP430F2013IPW?
Current MSP430F2013IPW pricing is obtained through the Request a Quote form on this page. The form is the appropriate route for a quantity-specific quote because distributor pricing, inventory, and pack quantities can change without notice. Include the required order quantity, delivery location, acceptable packing format, and target date so the quote reflects the complete procurement requirement.
What is the lead time and stock status for MSP430F2013IPW?
Request the current MSP430F2013IPW stock position, manufacturing lead time, and minimum order quantity through the Request a Quote form on this page. Procurement review is necessary because availability can change with the exact orderable suffix and packing format. Include production quantity, scheduled build date, and any required traceability or quality documentation when requesting the quotation.

کے لیے انجینئرنگ ریفرنس ڈیٹا MSP430F2013IPW — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose MSP430F2013IPW for compact, low-power measurement and control products where a 16 MHz MSP430 CPU16 core, one 16-bit sigma-delta ADC, 128 bytes of RAM, and 2 KB of Flash are sufficient. The USI’s support for SPI and I2C makes the device suitable for small sensor nodes, industrial measurement modules, and programmable threshold controllers. Select a higher-memory MSP430 when code size, buffering, logging, or application complexity exceeds the target’s resources. Use a different MCU family when software requirements include a larger operating system, substantially more RAM, more ADC channels, faster conversion, or a broader communications portfolio. MSP430F2013IPW should also be selected only when the 14-pin TSSOP footprint, industrial temperature grade, ADC bandwidth, and available GPIO meet the mechanical and functional requirements of the finished product.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ
Brand Texas Instruments
Package 14-pin TSSOP
CPU Architecture 16-bit MSP430 CPU16 RISC
Maximum Clock Frequency 16 MHz
Flash Memory 2 KB
RAM 128 bytes
ADC One 16-bit sigma-delta ADC
Serial Interface USI supporting SPI and I2C
General-Purpose I/O 10 pins
Temperature Grade Industrial

اہم امتیازی خصوصیات

  • Integrated high-resolution sigma-delta conversion (بمقابلہHigher-memory MSP430 variants)
  • Compact mixed-signal integration (بمقابلہExternal ADC implementations)
  • Protocol-flexible serial communications (بمقابلہSerial-interface-free microcontroller variants)

ڈیزائن نوٹس

Confirm the complete power-consumption profile with the manufacturer electrical characteristics before selecting the supply and battery. The MSP430F2013IPW has a 16 MHz clock rating, but real operating current depends on the active clock, ADC conversion schedule, USI activity, GPIO state, and whether the CPU is running or placed into a low-power state. Use the datasheet current figures for each operating mode and avoid leaving unused inputs floating. Decoupling and supply sequencing must follow the power-pin requirements shown in the manufacturer pin-description and application guidance.

Keep analog sensor traces short and isolate them from clock, USI, and other switching paths. The sigma-delta ADC is intended for measurement of suitable bandwidth-limited signals, so a slow signal does not justify a long high-impedance route through electrically noisy PCB areas. Use a continuous ground reference, place input components near the ADC source, and keep return-current paths direct. Validate the final input filter against both the desired measurement bandwidth and the ADC acquisition requirements before releasing the layout.

Do not select MSP430F2013IPW solely from its 16 MHz clock rating. Confirm that 2 KB of Flash and 128 bytes of RAM accommodate the application code, stack, constants, and communication buffers. Also verify that one ADC, ten I/O pins, and the USI satisfy the interface plan. During programming, connect the target correctly to a supported JTAG or Spy-Bi-Wire setup and use the manufacturer pin-description table for test, reset, power, ground, and GPIO assignments.

For a SPI sensor design, calculate the communication duty cycle from the transaction rate, bus width, and required settling time. The USI supports SPI or I2C, but the selected protocol, slave address strategy, pull resistors, and maximum clock determine the implementation. Keep the sensor and MCU rails local to the relevant circuitry, provide the required bypass capacitance close to the device, and verify the ADC reference relationship if analog and digital measurements are correlated.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated for this orderable code. AEC-Q100 is not applicable because MSP430F2013IPW is an industrial mixed-signal microcontroller rather than an automotive-qualified device.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-20 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

MSP430F2013IPW MSP430F2013IPW datasheet MSP430F2013IPW pinout MSP430F2013IPW datasheet pdf Texas Instruments MSP430F2013IPW MSP430F2013IPW equivalent MSP430F2013IPW replacement MSP430F2013IPW cross reference MSP430F2013IPW schematic MSP430F2013IPW programming MSP430F2013IPW price MSP430F2013IPW stock MSP430F2013 14-TSSOP pinout MSP430F2013 application circuit

متعلقہ اجزاء اور اصطلاحات

Texas Instruments MSP430F2013IPW MSP430F2013IPWR MSP430F2013 MSP-TS430PW14 MSP430 CPU16 microcontroller mixed-signal microcontroller embedded processor semiconductor ultra-low-power MCU 16-bit sigma-delta ADC analog comparator Universal Serial Interface SPI I2C JTAG Spy-Bi-Wire 14-pin TSSOP TSSOP package family surface-mount package Flash memory RAM industrial sensor mixed-signal measurement
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں