MSP430F2013IPW - 16MHz Low-Power MCU | Texas Instruments
MPN: MSP430F2013IPW ✓ Hoạt độngMSP430F2013IPW Tóm tắt
An ultra-low-power mixed-signal microcontroller is a semiconductor device designed to execute embedded control and measurement tasks while consuming very little energy. The MSP430 platform combines a 16-bit RISC processor, analog sensing capability, timers, communication peripherals, and GPIO in one compact component. Its architecture belongs to the microcontroller and embedded-processing hierarchy, making it especially useful for battery-operated instruments, industrial sensors, and compact control systems.
The MSP430F2013IPW combines a 16 MHz CPU16 core with 2 KB Flash and 128 bytes of RAM. Its mixed-signal resources include a 16-bit sigma-delta ADC and a versatile analog comparator. The Universal Serial Interface provides synchronous serial communication through SPI or I2C, while the built-in timer supports periodic measurement and control tasks. Ten I/O pins give the device enough external connectivity for compact sensor nodes and embedded control boards.
The MSP430 CPU16 uses 16-bit registers and a RISC instruction set optimized for low-power operation. The sigma-delta ADC is intended for measurement paths where resolution and noise performance matter more than conversion speed. Because the MCU combines digital processing and analog measurement, it can reduce external component count in sensing products. Firmware can configure the USI for either SPI or I2C according to the peripheral ecosystem and board-level requirements.
Typical uses include portable environmental monitors, industrial measurement instruments, low-power sensor interfaces, compact data-acquisition nodes, and embedded control products. The 14-pin TSSOP package is useful where a small PCB footprint is required. The MSP-TS430PW14 target board supports programming and debugging for MSP430F2x and MSP430G2x devices using JTAG or Spy-Bi-Wire, making it a practical development platform for initial firmware bring-up.
When laying out a design, reserve the decoupling and programming interface pins required by the device, keep sensitive analog routing away from fast digital switching, and validate the ADC input network against the measurement bandwidth. Program conversion and communication behavior through the USI and confirm the required clock, reset, and debugger connections against the manufacturer pin-description table before releasing the PCB.
This page combines manufacturer specifications, sourcing guidance, application analysis, and engineering design notes to support MCU selection and board development. It also highlights the importance of checking memory requirements, peripheral compatibility, and package-level pin assignments before committing MSP430F2013IPW to a production design.
Bộ thay thế dễ dàng lắp đặt cho MSP430F2013IPW — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MSP430F2013IPW (cùng hình factor và footprint) — khác nhau ở ADC Resolution, CPU Architecture, Package, Operating Temperature Range, Supply Voltage.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếMSP430F2013IPW Tỷ lệ tối đa & tính chất điện
| CPU Architecture | MSP430 CPU16 16-bit RISC |
| Tần số xung maksimum | 16 MHz |
| Flash Memory | 2 KB |
| RAM | 128 bytes |
| ADC Type | 16-bit sigma-delta ADC |
| ADC Quantity | 1 |
| Serial Interface | USI supporting SPI and I2C |
| Analog Comparator | 1 |
| General-Purpose I/O | 10 pins |
| Timer | 16-bit |
| Hộp | 14-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Operating Temperature Grade | Industrial |
Hướng dẫn cấu hình chân MSP430F2013IPW 14-pin tssop
Cấu hình chân cho MSP430F2013IPW (14-pin tssop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho MSP430F2013IPW.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MSP430F2013IPW phù hợp cho 6 Áp dụngs: Portable Environmental Sensor, Industrial Process Measurement, Compact Data Acquisition Node, Battery-Powered Meter, SPI Sensor Interface, Programmable Threshold Controller.
Portable Environmental Sensor
The MSP430F2013IPW is well suited to a battery-powered environmental sensor because it combines a 16 MHz MSP430 CPU16 core with a 16-bit sigma-delta ADC in one 14-pin TSSOP device. The ADC can acquire low-bandwidth analog measurements while the microcontroller performs filtering, threshold evaluation, and sensor compensation. Its 2 KB Flash and 128 bytes of RAM support compact control firmware rather than demanding high-compute workloads. A practical design can configure the USI for I2C or SPI to connect a digital temperature, humidity, or gas sensor. Power consumption depends on the selected clock, ADC conversion schedule, communication rate, and duty cycle, so battery sizing should use the complete firmware operating profile.
Được đề xuất
Industrial Process Measurement
MSP430F2013IPW can serve as the controller for a compact industrial process-measurement node when the signal requires moderate resolution rather than high-rate conversion. Its 16-bit sigma-delta ADC is suited to slowly changing process variables, while the built-in comparator can support threshold detection and supervisory functions. The 16-bit timer provides a basis for periodic sampling and control timing, and the USI can communicate with remote sensor or actuator electronics through I2C or SPI. Industrial designs should verify the operating-temperature grade, isolation requirements, input protection, and analog accuracy at the intended supply voltage. Firmware can also compensate sensor offset and gain, detect open inputs, and transmit processed measurements over the selected serial interface.
Được đề xuất
Compact Data Acquisition Node
The MSP430F2013IPW is appropriate for a low-channel-count data-acquisition node that must acquire, filter, and forward analog measurements without a large application processor. Its 16-bit sigma-delta ADC supports measurement of slow or band-limited signals, while the CPU16 core can apply calibration, digital filtering, and units conversion within the available 2 KB of Flash. The USI provides a practical path to a local display, external memory, or host processor through I2C or SPI. Because RAM is limited to 128 bytes, the firmware should use a streaming data model and avoid retaining large sample buffers. The 14-pin TSSOP package also helps reduce board area, although analog layout should preserve a clean return path and minimize coupling between sensor inputs and digital communication lines.
Được đề xuất
Battery-Powered Meter
MSP430F2013IPW fits a battery-powered meter that combines analog measurement with a compact serial interface. The 16-bit sigma-delta ADC can measure a conditioned sensor signal, while the MSP430 CPU16 core performs scaling, calibration, and limit checks. The USI can drive a display driver, data logger, or external radio through I2C or SPI, and the 128-byte RAM supports short working buffers and stack operations. Because the available Flash is limited to 2 KB, complex user interfaces and extensive data storage are better assigned to external components. Design work should focus on sleep-state behavior, startup-time requirements, reference accuracy, and the analog front end. Use the manufacturer ADC and electrical-characteristic sections to establish timing and accuracy limits.
Được đề xuất
SPI Sensor Interface
The MSP430F2013IPW is suitable for a compact SPI sensor interface because its Universal Serial Interface supports synchronous SPI communication. The 16 MHz CPU16 core provides enough processing capability to configure the sensor, collect measurements, perform basic filtering, and forward results over another serial link. Its 16-bit sigma-delta ADC can monitor an auxiliary analog channel or supply a threshold input, and the built-in comparator supports simple event detection. SPI clocking, chip-select handling, and sensor timing should be implemented against the peripheral and device data requirements. Board layout should keep clock and data traces short, provide a defined return path, and account for signal-integrity behavior at the intended clock rate. Firmware validation should cover startup delay, conversion timing, and sensor fault handling.
Được đề xuất
Programmable Threshold Controller
MSP430F2013IPW can implement a programmable threshold controller for industrial or instrumentation systems that require local analog decision-making. The integrated analog comparator can observe a reference or sensor signal, while the 16-bit sigma-delta ADC provides a higher-resolution measurement path when the application needs calibrated readings. The 16-bit timer can establish measurement intervals or output timing, and the USI can report state changes to a supervisory controller. The device’s 2 KB Flash and 128 bytes of RAM favor a focused firmware structure with compact calibration tables. Designers should evaluate comparator and ADC input ranges, noise behavior, threshold stability, and output timing before fixing the control architecture. A development board such as MSP-TS430PW14 can support firmware bring-up and peripheral validation before the embedded design is finalized.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MSP430F2013IPW — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Texas Instruments |
| Package | 14-pin TSSOP |
| CPU Architecture | 16-bit MSP430 CPU16 RISC |
| Maximum Clock Frequency | 16 MHz |
| Flash Memory | 2 KB |
| RAM | 128 bytes |
| ADC | One 16-bit sigma-delta ADC |
| Serial Interface | USI supporting SPI and I2C |
| General-Purpose I/O | 10 pins |
| Temperature Grade | Industrial |
Bảo phân biệt quan trọng
- Integrated high-resolution sigma-delta conversion (vsHigher-memory MSP430 variants)
- Compact mixed-signal integration (vsExternal ADC implementations)
- Protocol-flexible serial communications (vsSerial-interface-free microcontroller variants)
Ghi chú thiết kế
Confirm the complete power-consumption profile with the manufacturer electrical characteristics before selecting the supply and battery. The MSP430F2013IPW has a 16 MHz clock rating, but real operating current depends on the active clock, ADC conversion schedule, USI activity, GPIO state, and whether the CPU is running or placed into a low-power state. Use the datasheet current figures for each operating mode and avoid leaving unused inputs floating. Decoupling and supply sequencing must follow the power-pin requirements shown in the manufacturer pin-description and application guidance.
Keep analog sensor traces short and isolate them from clock, USI, and other switching paths. The sigma-delta ADC is intended for measurement of suitable bandwidth-limited signals, so a slow signal does not justify a long high-impedance route through electrically noisy PCB areas. Use a continuous ground reference, place input components near the ADC source, and keep return-current paths direct. Validate the final input filter against both the desired measurement bandwidth and the ADC acquisition requirements before releasing the layout.
Do not select MSP430F2013IPW solely from its 16 MHz clock rating. Confirm that 2 KB of Flash and 128 bytes of RAM accommodate the application code, stack, constants, and communication buffers. Also verify that one ADC, ten I/O pins, and the USI satisfy the interface plan. During programming, connect the target correctly to a supported JTAG or Spy-Bi-Wire setup and use the manufacturer pin-description table for test, reset, power, ground, and GPIO assignments.
For a SPI sensor design, calculate the communication duty cycle from the transaction rate, bus width, and required settling time. The USI supports SPI or I2C, but the selected protocol, slave address strategy, pull resistors, and maximum clock determine the implementation. Keep the sensor and MCU rails local to the relevant circuitry, provide the required bypass capacitance close to the device, and verify the ADC reference relationship if analog and digital measurements are correlated.
Thông tin tuân thủ
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status is stated for this orderable code. AEC-Q100 is not applicable because MSP430F2013IPW is an industrial mixed-signal microcontroller rather than an automotive-qualified device.