Texas Instruments

OPA404AG - 6.4MHz Precision Quad Op Amp | Texas Instruments

Teilenummer: OPA404AG ✓ Aktiv
±750 uV maximum Vdss ±4 pA maximum Id 14-CDIP Package
MOQ: 1 |

OPA404AG Übersicht

The Texas Instruments OPA404AG is a four-channel, high-speed precision DiFET operational amplifier with 6.4 MHz gain-bandwidth product, 35 V/us slew rate, and ±750 uV maximum input offset voltage. The OPA404AG is supplied in a 14-CDIP package and is specified for operation from a minimum total supply of 10 V to a maximum total supply of 36 V.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to control gain and bandwidth. The OPA404 belongs to the precision operational-amplifier hierarchy, which includes voltage-feedback amplifiers, analog signal-chain ICs, and broader semiconductor devices. Its input-cascode architecture combines precision input characteristics with high-speed performance, while its standard quad pin configuration allows four amplifiers to be used in one package.

Key features include a 6.4 MHz wide bandwidth, 35 V/us high slew rate, ±750 uV maximum offset voltage, and ±4 pA maximum bias current. The amplifier is unity-gain stable, allowing direct use in voltage-follower configurations without a frequency-compensation network. Its specified 0.01% settling performance supports precise, high-speed feedback systems where waveform accuracy must be maintained after a transition.

The DiFET input stage and input-cascode design are central to the OPA404's performance. The cascode arrangement supports high precision input specifications while preserving wide bandwidth and rapid slew performance. With four independent channels in one package, the device can implement matched amplifier functions, current-feedback paths, instrumentation circuits, active filters, or general-purpose analog signal conditioning where one package per channel is undesirable.

Typical uses include precision signal conditioning, low-level sensor amplification, instrumentation, data-acquisition front ends, active filtering, and audio or communications circuits. Designers can use the unity-gain stability for voltage followers, or apply external feedback networks for inverting, non-inverting, and differential amplifier configurations. Care must be taken to maintain adequate phase margin, observe the supply-voltage limits, and account for input and output common-mode restrictions.

When laying out a board, place each input, feedback component, and decoupling capacitor close to the corresponding amplifier pins. Use a stable low-noise reference for precision measurements, verify common-mode and output-swing limits at the selected supply voltage, and test the completed circuit for stability across the intended gain and frequency ranges. The ceramic-DIP package is mechanically larger than typical surface-mount alternatives, so board area and socket availability should be considered before design release.

This page combines the manufacturer's key electrical characteristics with package information, application guidance, comparison parameters, and a conservative drop-in assessment. It also identifies where OPA404AG alternatives were not established, helping engineers distinguish a verified pin-compatible replacement from a merely similar amplifier.

Drop-in-Alternativen für OPA404AG – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit OPA404AG (gleiche Bauform und Footprint) – abweichend in Number of Channels, Package.

Texas Instruments
Number of Channels: 4
Package: 14-CDIP (ceramic dual-in-line)
Vergleichen mit OPA404AG →

OPA404SG

✅ Drop-In
Texas Instruments
📦 14-CDIP
4 · 6.4 MHz · 35 V/us · +/-750 uV · +/-4 pA · 0.01% · 36 V · 10 V

Preis auf Anfrage

Datenblatt ansehen →

OPA404AG Grenzwerte & elektrische Eigenschaften

Amplifier Type Quad precision voltage-feedback operational amplifier
Number of Channels 4 channels
Gain-Bandwidth Product 6.4 MHz
Slew Rate 35 V/us
Input Offset Voltage ±750 uV maximum
Input Bias Current ±4 pA maximum
Minimum Total Supply Voltage 10 V
Maximum Total Supply Voltage 36 V
Nominal Total Supply Voltage 30 V
Unity-Gain Stability Yes
Settling Accuracy 0.01%
Input Architecture Input-cascode DiFET operational amplifier
Gehäuse 14-CDIP
Montageart Through-hole

OPA404AG 14-cdip Pinbelegungsleitfaden

Pinbelegung für OPA404AG (14-cdip-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für OPA404AG im 14-cdip-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für OPA404AG.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

OPA404AG ist geeignet für 6 Anwendungs: Precision Instrumentation Signal Conditioning, Data Acquisition Front End, Active Audio Filters, High-Impedance Sensor Amplification, Communication Signal Conditioning, Precision Reference Buffering.

🏭

Precision Instrumentation Signal Conditioning

OPA404AG fits precision instrumentation because each of its four channels combines a 6.4 MHz gain-bandwidth product with a maximum input offset voltage of ±750 uV. Place the amplifier in a non-inverting or differential conditioning stage between a sensor and an ADC, then use the fourth channel for reference buffering or active compensation. The 35 V/us slew rate allows relatively fast signal transitions, while unity-gain stability supports direct voltage-follower use. Validate the selected gain, common-mode range, output swing, and noise contribution against the actual sensor impedance and measurement bandwidth before release.

📊

Data Acquisition Front End

OPA404AG can serve as the analog front end of a data-acquisition system when low offset and controlled bias current are important. Its ±750 uV maximum offset and ±4 pA maximum bias current help reduce systematic error when conditioning moderate- or high-impedance sources, while the 6.4 MHz bandwidth is well suited to many multiplexed acquisition channels. Use one or more channels for differential gain, add another for reference buffering, and reserve the fourth for monitor or test functions. Account for ADC input range, settling requirements, source capacitance, and the amplifier's output-swing limits in the system design.

🎧

Active Audio Filters

OPA404AG is appropriate for active audio filtering when a low-offset, high-speed voltage-feedback amplifier is needed. Its 6.4 MHz gain-bandwidth product gives ample bandwidth for many audio-band filter stages, and the 35 V/us slew rate helps preserve low-distortion large-signal behavior. The unity-gain-stable configuration also permits filter stages that approach unity gain. Select resistor and capacitor values with practical tolerances in mind, check the resulting gain at the highest operating frequency, and verify that the output remains within the available rail-dependent swing.

🧩

High-Impedance Sensor Amplification

OPA404AG is useful for high-impedance sensor amplification because its maximum input bias current is ±4 pA. The low-bias-current input stage helps prevent source loading in sensor circuits, while the ±750 uV maximum input offset limits the DC error introduced by a precision gain stage. Use the amplifier with suitable feedback resistors and, where required, input biasing and guarding to control parasitic capacitance. Verify common-mode operating range, output swing, noise, and stability at the selected closed-loop gain before connecting a high-impedance transducer.

🌐

Communication Signal Conditioning

OPA404AG can condition low-level communication signals when a design requires both precision offset behavior and wide bandwidth. Its 6.4 MHz gain-bandwidth product supports moderate-bandwidth gain stages, and 35 V/us slew rate helps maintain signal amplitude through rapidly varying waveforms. A quad package allows separate paths for receive amplification, transmit-loop shaping, level detection, and buffering. Confirm common-mode range and output headroom for the interface voltage, keep trace lengths short where feedback loops are sensitive, and test crosstalk, settling, and stability with the actual source and load impedances.

⚡

Precision Reference Buffering

OPA404AG can buffer a precision reference voltage where low offset, unity-gain stability, and fast settling are desirable. The ±750 uV maximum input offset is important when the buffer output accuracy directly contributes to the system reference, and the 35 V/us slew rate allows the output to follow reference transitions more rapidly than a general-purpose amplifier. Use one channel for the main buffer and additional channels for reference distribution or auxiliary functions. Check capacitive loading, output swing, noise, and the reference source's stability characteristics to ensure the buffered node remains accurate.

What is the OPA404AG?
The OPA404AG is a four-channel, high-speed precision DiFET operational amplifier from Texas Instruments. According to the manufacturer datasheet, it combines a 6.4 MHz gain-bandwidth product, 35 V/us slew rate, ±750 uV maximum input offset voltage, and unity-gain stability in a 14-CDIP package. Its input-cascode design supports precision input specifications while preserving wide-bandwidth operation.
What are the key specifications of OPA404AG that engineers should know?
The OPA404AG provides four amplifier channels, 6.4 MHz gain-bandwidth product, 35 V/us slew rate, and ±750 uV maximum input offset voltage. The manufacturer datasheet also specifies ±4 pA maximum bias current, 0.01% settling, and a standard quad pin configuration. Its total supply-voltage range is 10 V to 36 V, allowing operation at ±5 V, +12 V, ±15 V, or other supported rail combinations.
Where can I download the OPA404AG datasheet PDF?
The official OPA404AG datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/opa404.pdf. The manufacturer product page at https://www.ti.com/product/OPA404 provides ordering options, quality information, and additional product support. Use the pin-description table and electrical-characteristics tables in the manufacturer datasheet when assigning PCB functions or checking operating limits.
Where can I find the OPA404AG pinout?
Use the standard quad-op-amplifier pin configuration shown in the OPA404 manufacturer datasheet for the OPA404AG. The device is a 14-CDIP containing four amplifiers, with power connections and signal inputs distributed across the 14 leads. Because the exact lead names and exposed connection details are not stated in the product snippets, consult the manufacturer pinout table before assigning tracks or designing a socket.
Is the OPA404AG unity-gain stable?
Yes, the OPA404AG is unity-gain stable. According to the manufacturer datasheet, this allows the amplifier to operate as a voltage follower with a feedback factor of one while retaining its 6.4 MHz gain-bandwidth product. It also supports conventional inverting and non-inverting feedback networks, provided the selected closed-loop gain and external component values provide adequate phase margin.
What supply voltage can be used with the OPA404AG?
The OPA404AG operates from 10 V to 36 V total supply voltage. Texas Instruments describes this as a nominal 30 V maximum total supply configuration, with the equivalent common rail ranges including ±5 V, ±12 V, and ±15 V. The verified OPA404AG comparison also reports minimum and maximum total supply values of 10 V and 36 V, respectively.
What can replace the OPA404AG?
No verified five-part drop-in replacement set was established for the OPA404AG. OPA404SG is the closest documented same-family candidate from the available comparison, but its electrical details and suitability for every OPA404AG application require confirmation in the manufacturer datasheet. Treat functionally similar quad amplifiers as redesign candidates unless their package, pinout, supply range, offset, bandwidth, slew rate, and stability have all been verified.
Is OPA404AG the same as OPA404SG?
The OPA404AG and OPA404SG belong to the same Texas Instruments OPA404 family, but they should not be treated as automatically interchangeable without reviewing the ordering table and datasheet. The available comparison shows both devices with four channels and the same 10 V to 36 V total supply range. Confirm package, temperature grade, electrical limits, and orderable status before substituting OPA404SG for OPA404AG.
OPA404AG vs OPA404SG: which is better for precision instrumentation?
OPA404AG is the appropriate choice when the documented 14-CDIP construction and its associated operating grade suit the instrument. OPA404SG is a same-family candidate that may be useful when its package, temperature rating, and electrical characteristics meet the design. The available comparison confirms four channels and the same 10 V to 36 V total supply range for both, but it does not provide enough data for a universal performance winner.
When should I choose OPA404AG over another precision quad op amp?
Choose OPA404AG when a design needs four high-speed precision amplifiers in a single 14-CDIP package, a 6.4 MHz gain-bandwidth product, 35 V/us slew rate, low maximum offset of ±750 uV, and unity-gain stability. It is especially suitable for precision signal conditioning, instrumentation, active filtering, and data-acquisition front ends where the through-hole package and analog performance justify the larger board footprint.
Is OPA404AG suitable for active filters and sensor interfaces?
Yes, OPA404AG is suitable for active filters and precision sensor interfaces when the circuit remains within the device's specified supply, common-mode, output-swing, offset, and stability limits. Its 6.4 MHz bandwidth and 35 V/us slew rate support moderate-frequency signal paths, while ±4 pA maximum bias current is useful with high-impedance sensors. Confirm actual source impedance, noise requirements, and phase margin during design verification.
What power and thermal considerations apply to OPA404AG?
OPA404AG is a precision analog amplifier rather than a power semiconductor, so it does not require a safe-operating-area chart. Thermal design should focus on total supply current, ambient temperature, and the thermal resistance of the specific 14-CDIP package and PCB environment. Keep dissipation calculations and temperature-rise estimates separate from the manufacturer's absolute maximum ratings, and confirm the final operating region against the datasheet.
Where can I buy OPA404AG and check its current lead time?
Use the Request a Quote form on this page to request OPA404AG availability, quantity, and current lead time from XAIPART. The available distributor listing confirms a 14-CDIP, four-circuit general-purpose amplifier listing for the exact MPN, but its snippet does not print qualifying quantity-break prices or a firm lead-time commitment. A current quote should therefore confirm stock, packaging form, and delivery timing.
How much does OPA404AG cost?
Request a current OPA404AG quotation through the Request a Quote form on this page because pricing and availability can change with quantity, package form, and market conditions. The verified distributor listing contains no numeric quantity-break table, so no current unit-price tiers are reproduced in the structured offer. The quote team can confirm one-piece, production-volume, and scheduled-delivery pricing for the exact 14-CDIP MPN.
Is OPA404AG currently in stock and what is its lead time?
Current OPA404AG stock and lead time should be requested through the Request a Quote form on this page. The product listing indicates that OPA404AG is offered as a standard four-circuit, 14-CDIP amplifier, but it does not establish a guaranteed stock quantity or delivery date. Include the required quantity, target package form, and production schedule when requesting the commitment.
What compliance and lifecycle information is available for OPA404AG?
The OPA404AG is presented as an active Texas Instruments product, but the verified material does not provide a specific RoHS, REACH, AEC-Q100, lead-free, or halogen-free statement. Treat those compliance fields as unknown until the manufacturer product page or current material declaration is checked. For automotive use, confirm AEC-Q100 qualification explicitly; it should not be inferred merely because the amplifier is precision and low-offset.

Technische Referenzdaten für OPA404AG – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose OPA404AG when the design requires four precision, high-speed amplifiers in a 14-CDIP package and can benefit from 6.4 MHz bandwidth, 35 V/us slew rate, ±750 uV maximum offset, and ±4 pA maximum bias current. It is well matched to instrumentation, sensor interfaces, active filters, reference buffering, and general precision signal-conditioning systems. OPA404SG is the closest same-family alternative documented here and is reasonable to investigate when its package grade and full electrical characteristics meet the design. It should not replace the OPA404AG without a direct review of pinout, temperature range, offset, bandwidth, bias current, and stability. Do not substitute general-purpose or precision quad amplifiers solely on channel count; a true drop-in decision requires compatibility with the 10 V to 36 V total supply requirement and the existing feedback network. For new compact designs, a surface-mount alternative may be preferable when the 14-CDIP footprint is undesirable, provided the electrical and layout changes are evaluated rather than treated as a drop-in replacement.

Vergleich mit Alternativen

Parameter Dieses Produkt OPA404SG
Package 14-CDIP 14-CDIP
Brand Texas Instruments Texas Instruments
Number of Channels 4 channels 4 channels
Amplifier Family OPA404 high-speed precision DiFET operational amplifier OPA404 high-speed precision DiFET operational amplifier
Minimum Total Supply Voltage 10 V 10 V
Maximum Total Supply Voltage 36 V 36 V

Wichtigste Unterscheidungsmerkmale

  • Combines precision offset performance with high-speed operation (vs. OPA404SG)
  • Provides four amplifiers in one 14-CDIP package (vs. OPA404SG)
  • Supports direct voltage-follower operation (vs. OPA404SG)

Designhinweise

Place each amplifier's input and feedback components close to its corresponding pins, and route the feedback loop away from high-impedance input and output traces. The input-cascode architecture supports precision operation, but long parallel input runs can increase parasitic capacitance and sensitivity to interference. Use a solid ground plane, minimize loop area, and verify the assembled board with a scope when working near the amplifier's 6.4 MHz bandwidth.

Decouple each supply connection with local high-frequency bypass capacitance and provide adequate bulk capacitance where the board-level distribution network requires it. Confirm the actual total supply voltage remains between 10 V and 36 V and that the output does not exceed the rail-dependent swing. OPA404AG is a precision analog IC rather than a power semiconductor, so SOA data is not applicable; thermal review should instead use total supply current and the package's specified operating limits.

Do not equate unity-gain stability with unconditional stability at every externally configured gain. Check the closed-loop gain, feedback resistor values, load impedance, and source capacitance, especially in active filters. Also avoid selecting a replacement solely because it is a quad op amp: confirm the 14-CDIP pin configuration, supply limits, offset voltage, bias current, bandwidth, slew rate, and operating temperature before approving a substitution.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was present in the verified product material.

Ähnliche Suchanfragen

OPA404AG datasheet OPA404AG pinout OPA404AG datasheet pdf OPA404AG equivalent OPA404AG replacement OPA404AG cross reference OPA404AG vs OPA404SG OPA404AG price OPA404AG stock Texas Instruments OPA404AG OPA404 14-CDIP precision op amp OPA404AG active filter OPA404AG instrumentation amplifier OPA404AG 6.4MHz 35V/us OPA404AG 14 pin pinout

Verwandte Bauteile & Begriffe

Texas Instruments OPA404AG OPA404SG OPA404 operational amplifier precision operational amplifier voltage-feedback amplifier quad amplifier DiFET operational amplifier input cascode gain-bandwidth product slew rate input offset voltage input bias current unity-gain stability common-mode input voltage 14-CDIP through-hole package signal conditioning precision instrumentation active filter data acquisition high-impedance sensor reference buffer communication signal conditioning
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen