OPA404AG - 6.4MHz Precision Quad Op Amp | Texas Instruments
Référence : OPA404AG ✓ ActifOPA404AG Présentation
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to control gain and bandwidth. The OPA404 belongs to the precision operational-amplifier hierarchy, which includes voltage-feedback amplifiers, analog signal-chain ICs, and broader semiconductor devices. Its input-cascode architecture combines precision input characteristics with high-speed performance, while its standard quad pin configuration allows four amplifiers to be used in one package.
Key features include a 6.4 MHz wide bandwidth, 35 V/us high slew rate, ±750 uV maximum offset voltage, and ±4 pA maximum bias current. The amplifier is unity-gain stable, allowing direct use in voltage-follower configurations without a frequency-compensation network. Its specified 0.01% settling performance supports precise, high-speed feedback systems where waveform accuracy must be maintained after a transition.
The DiFET input stage and input-cascode design are central to the OPA404's performance. The cascode arrangement supports high precision input specifications while preserving wide bandwidth and rapid slew performance. With four independent channels in one package, the device can implement matched amplifier functions, current-feedback paths, instrumentation circuits, active filters, or general-purpose analog signal conditioning where one package per channel is undesirable.
Typical uses include precision signal conditioning, low-level sensor amplification, instrumentation, data-acquisition front ends, active filtering, and audio or communications circuits. Designers can use the unity-gain stability for voltage followers, or apply external feedback networks for inverting, non-inverting, and differential amplifier configurations. Care must be taken to maintain adequate phase margin, observe the supply-voltage limits, and account for input and output common-mode restrictions.
When laying out a board, place each input, feedback component, and decoupling capacitor close to the corresponding amplifier pins. Use a stable low-noise reference for precision measurements, verify common-mode and output-swing limits at the selected supply voltage, and test the completed circuit for stability across the intended gain and frequency ranges. The ceramic-DIP package is mechanically larger than typical surface-mount alternatives, so board area and socket availability should be considered before design release.
This page combines the manufacturer's key electrical characteristics with package information, application guidance, comparison parameters, and a conservative drop-in assessment. It also identifies where OPA404AG alternatives were not established, helping engineers distinguish a verified pin-compatible replacement from a merely similar amplifier.
Alternatives de remplacement direct pour OPA404AG — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec OPA404AG (même facteur de forme et même empreinte) — différant par Number of Channels, Package.
OPA404SG
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →OPA404AG Valeurs maximales et caractéristiques électriques
| Amplifier Type | Quad precision voltage-feedback operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 6.4 MHz |
| Slew Rate | 35 V/us |
| Input Offset Voltage | ±750 uV maximum |
| Input Bias Current | ±4 pA maximum |
| Minimum Total Supply Voltage | 10 V |
| Maximum Total Supply Voltage | 36 V |
| Nominal Total Supply Voltage | 30 V |
| Unity-Gain Stability | Yes |
| Settling Accuracy | 0.01% |
| Input Architecture | Input-cascode DiFET operational amplifier |
| Boîtier | 14-CDIP |
| Type de montage | Through-hole |
Guide de configuration des broches du OPA404AG 14-cdip
Configuration des broches du OPA404AG (boîtier 14-cdip). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour OPA404AG.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
OPA404AG convient pour 6 applications: Precision Instrumentation Signal Conditioning, Data Acquisition Front End, Active Audio Filters, High-Impedance Sensor Amplification, Communication Signal Conditioning, Precision Reference Buffering.
Precision Instrumentation Signal Conditioning
OPA404AG fits precision instrumentation because each of its four channels combines a 6.4 MHz gain-bandwidth product with a maximum input offset voltage of ±750 uV. Place the amplifier in a non-inverting or differential conditioning stage between a sensor and an ADC, then use the fourth channel for reference buffering or active compensation. The 35 V/us slew rate allows relatively fast signal transitions, while unity-gain stability supports direct voltage-follower use. Validate the selected gain, common-mode range, output swing, and noise contribution against the actual sensor impedance and measurement bandwidth before release.
Recommandé
Data Acquisition Front End
OPA404AG can serve as the analog front end of a data-acquisition system when low offset and controlled bias current are important. Its ±750 uV maximum offset and ±4 pA maximum bias current help reduce systematic error when conditioning moderate- or high-impedance sources, while the 6.4 MHz bandwidth is well suited to many multiplexed acquisition channels. Use one or more channels for differential gain, add another for reference buffering, and reserve the fourth for monitor or test functions. Account for ADC input range, settling requirements, source capacitance, and the amplifier's output-swing limits in the system design.
Recommandé
Active Audio Filters
OPA404AG is appropriate for active audio filtering when a low-offset, high-speed voltage-feedback amplifier is needed. Its 6.4 MHz gain-bandwidth product gives ample bandwidth for many audio-band filter stages, and the 35 V/us slew rate helps preserve low-distortion large-signal behavior. The unity-gain-stable configuration also permits filter stages that approach unity gain. Select resistor and capacitor values with practical tolerances in mind, check the resulting gain at the highest operating frequency, and verify that the output remains within the available rail-dependent swing.
Recommandé
High-Impedance Sensor Amplification
OPA404AG is useful for high-impedance sensor amplification because its maximum input bias current is ±4 pA. The low-bias-current input stage helps prevent source loading in sensor circuits, while the ±750 uV maximum input offset limits the DC error introduced by a precision gain stage. Use the amplifier with suitable feedback resistors and, where required, input biasing and guarding to control parasitic capacitance. Verify common-mode operating range, output swing, noise, and stability at the selected closed-loop gain before connecting a high-impedance transducer.
Recommandé
Communication Signal Conditioning
OPA404AG can condition low-level communication signals when a design requires both precision offset behavior and wide bandwidth. Its 6.4 MHz gain-bandwidth product supports moderate-bandwidth gain stages, and 35 V/us slew rate helps maintain signal amplitude through rapidly varying waveforms. A quad package allows separate paths for receive amplification, transmit-loop shaping, level detection, and buffering. Confirm common-mode range and output headroom for the interface voltage, keep trace lengths short where feedback loops are sensitive, and test crosstalk, settling, and stability with the actual source and load impedances.
Recommandé
Precision Reference Buffering
OPA404AG can buffer a precision reference voltage where low offset, unity-gain stability, and fast settling are desirable. The ±750 uV maximum input offset is important when the buffer output accuracy directly contributes to the system reference, and the 35 V/us slew rate allows the output to follow reference transitions more rapidly than a general-purpose amplifier. Use one channel for the main buffer and additional channels for reference distribution or auxiliary functions. Check capacitive loading, output swing, noise, and the reference source's stability characteristics to ensure the buffered node remains accurate.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour OPA404AG — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | OPA404SG |
|---|---|---|
| Package | 14-CDIP | 14-CDIP |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 4 channels | 4 channels |
| Amplifier Family | OPA404 high-speed precision DiFET operational amplifier | OPA404 high-speed precision DiFET operational amplifier |
| Minimum Total Supply Voltage | 10 V | 10 V |
| Maximum Total Supply Voltage | 36 V | 36 V |
Principaux différenciateurs
- Combines precision offset performance with high-speed operation (vs OPA404SG)
- Provides four amplifiers in one 14-CDIP package (vs OPA404SG)
- Supports direct voltage-follower operation (vs OPA404SG)
Notes de conception
Place each amplifier's input and feedback components close to its corresponding pins, and route the feedback loop away from high-impedance input and output traces. The input-cascode architecture supports precision operation, but long parallel input runs can increase parasitic capacitance and sensitivity to interference. Use a solid ground plane, minimize loop area, and verify the assembled board with a scope when working near the amplifier's 6.4 MHz bandwidth.
Decouple each supply connection with local high-frequency bypass capacitance and provide adequate bulk capacitance where the board-level distribution network requires it. Confirm the actual total supply voltage remains between 10 V and 36 V and that the output does not exceed the rail-dependent swing. OPA404AG is a precision analog IC rather than a power semiconductor, so SOA data is not applicable; thermal review should instead use total supply current and the package's specified operating limits.
Do not equate unity-gain stability with unconditional stability at every externally configured gain. Check the closed-loop gain, feedback resistor values, load impedance, and source capacitance, especially in active filters. Also avoid selecting a replacement solely because it is a quad op amp: confirm the 14-CDIP pin configuration, supply limits, offset voltage, bias current, bandwidth, slew rate, and operating temperature before approving a substitution.
Informations de conformité
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was present in the verified product material.