PCA9518DWT - 5-Channel I2C Hub | Texas Instruments
Teilenummer: PCA9518DWT ✓ AktivPCA9518DWT Übersicht
An I2C hub is an interface IC that buffers two-way serial-bus signals and divides one electrical bus into multiple branches. This topology extends practical bus reach beyond the 400 pF limit associated with a conventional I2C segment, reduces loading on individual branches, and improves system partitioning. The PCA9518 belongs to the broader I2C interface-controller and interface-IC hierarchy within semiconductor and bus-management electronics.
The PCA9518 includes five downstream channels, bidirectional SDA and SCL propagation, and support for I2C and SMBus systems. Its 3 V to 3.6 V operating range suits low-voltage embedded equipment, while the 400 kHz bus speed covers standard- and fast-mode I2C traffic. Power-up or reset configuration and an enable or shutdown function provide control over how the hub behaves when the system starts or enters a low-power state.
Buffering creates separate bus branches, but correct implementation still depends on termination, pull-up placement, channel enable sequencing, and compliance with the I2C specification. The device does not generate protocol timing; it reproduces and buffers the SCL and SDA signals. Downstream devices still require suitable pull-up resistors, and each channel should be analyzed for capacitance, voltage rise time, and signal integrity.
Typical uses include sensor aggregation, industrial instrumentation, embedded control modules, programmable-logic systems, test equipment, and compact computer peripherals where several low-speed devices share a controller interface. The hub is particularly useful when cable length, device count, or branch capacitance would otherwise exceed the practical loading of one unbuffered I2C segment.
Designers should preserve the recommended input and output capacitance, route SDA and SCL consistently, and review timing behavior across every enabled channel. Verify voltage compatibility, enable polarity, reset behavior, and bus rise time against the attached devices. Because the downstream branches are electrically distinct, each branch should be tested independently for contention, ringing, and recovery after clock stretching.
This page summarizes the PCA9518 interface architecture, package and operating limits, verified replacement availability, and practical bus-segmentation guidance. It also identifies where a same-footprint substitute must be confirmed rather than inferred from a similar channel count, helping engineers shorten sourcing review while protecting PCB compatibility.
Drop-in-Alternativen für PCA9518DWT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernPCA9518DWT Technische Daten
| Device Type | Expandable five-channel I2C/SMBus buffer hub |
| Number of Channels | 5 downstream channels |
| Betriebsversorgungsspannung | 3 V to 3.6 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Maximum Bus Capacitance per Group | 400 pF |
| Signal Direction | Bidirectional |
| Supported Protocols | I2C and SMBus |
| Buffered Signals | SDA and SCL |
| Power-Up or Reset Configuration | Supported |
| Enable or Shutdown Function | Supported |
| Gehäuse | 20-pin SOIC |
| Montageart | Surface mount |
| Device Classification | Interface IC / I2C buffer hub |
PCA9518DWT 20-pin soic Pinbelegungsleitfaden
Pinbelegung für PCA9518DWT (20-pin soic-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für PCA9518DWT.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PCA9518DWT ist geeignet für 6 Anwendungs: Industrial Sensor Aggregation, Embedded Control Module Expansion, Programmable Logic Crossbar, Test and Measurement Front Ends, Smart Home and IoT Peripherals, Compact Computer Peripherals.
Industrial Sensor Aggregation
The PCA9518DWT fits industrial sensor systems that must distribute an I2C or SMBus connection across several groups of remote or densely packaged sensors. Its five bidirectional channels separate up to 400 pF per bus group, while the controller side remains connected to a single upstream interface. The 3 V to 3.6 V supply range and 400 kHz operating limit suit low-voltage measurement equipment. Use separate pull-ups on the downstream branches and confirm rise time for the longest branch, because buffering capacity does not remove transmission-line effects or determine resistor values by itself.
Empfohlen
Embedded Control Module Expansion
The PCA9518DWT is useful in embedded control modules where a microcontroller must connect to multiple I2C peripherals without concentrating all capacitance on one bus segment. Five downstream branches allow peripherals to be grouped by power state, sampling rate, or physical location. The hub buffers SDA and SCL bidirectionally at up to 400 kHz and operates from 3 V to 3.6 V. Firmware can use the enable and shutdown functions to avoid powering or driving unused branch devices, while reset and power-up configuration should be checked against the system startup sequence.
Empfohlen
Programmable Logic Crossbar
The PCA9518DWT can organize I2C peripherals connected to programmable logic systems where fan-out, predictable branch loading, and compact routing are important. The five-channel structure allows configuration devices, sensors, and status components to occupy separate downstream groups, each with a maximum stated capacitance of 400 pF. At 400 kHz, timing margin remains sensitive to trace length, pull-up strength, and downstream device behavior. Review the FPGA or programmable-logic I/O voltage against the 3 V to 3.6 V hub supply before applying it to low-voltage fabric interfaces.
Empfohlen
Test and Measurement Front Ends
The PCA9518DWT fits test and measurement front ends that combine several low-speed control peripherals, sensors, or data-acquisition components behind one host or embedded-controller bus. Separate branches reduce the capacitive burden presented by grouped devices and make channel troubleshooting more systematic. Its 400 kHz maximum rate is appropriate for configuration and status traffic rather than high-volume real-time acquisition. The design should include deterministic enable control, branch-specific pull-up networks, and continuity checks for each SDA and SCL path to prevent one peripheral from obscuring fault isolation.
Empfohlen
Smart Home and IoT Peripherals
The PCA9518DWT is applicable to smart-home and IoT controller boards that aggregate sensors, EEPROMs, display controllers, and other low-speed peripherals. Five downstream branches simplify partitioning of capacitive loads and can isolate groups according to power consumption or update rate. The 3 V to 3.6 V operating range aligns with many embedded platforms, and the 400 kHz bus rate supports standard I2C transactions. Keep each branch within 400 pF and avoid excessive cable lengths; long wiring should include appropriate protection and signal-conditioning measures rather than relying on hub buffering alone.
Empfohlen
Compact Computer Peripherals
The PCA9518DWT can serve compact computer peripherals requiring several I2C targets behind a controller-side bus, including configuration, status, and auxiliary sensor functions. Buffering SDA and SCL into five groups limits the electrical loading seen by the host interface and makes each peripheral group easier to power down. The device operates up to 400 kHz, which is suitable for configuration traffic and ordinary peripheral transactions. Designers should confirm that all downstream devices share a compatible logic level and verify hot-plug, power-up sequencing, and bus contention behavior before using the hub with removable or independently switched modules.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PCA9518DWT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Package | 20-pin SOIC |
| Brand | Texas Instruments |
| Device Type | Expandable five-channel I2C/SMBus buffer hub |
| Number of Channels | 5 |
| Operating Supply Voltage | 3 V to 3.6 V |
| Maximum Bus Frequency | 400 kHz |
| Maximum Capacitance per Group | 400 pF |
| Signal Direction | Bidirectional SDA and SCL |
| Power-Up or Reset Configuration | Supported |
| Enable or Shutdown Function | Supported |
Wichtigste Unterscheidungsmerkmale
- Five-channel buffered fan-out (vs. PCA9545AD,118)
- Higher per-group capacitance accommodation (vs. PCA9545AD,118)
- Bidirectional bus buffering with shutdown control (vs. PCA9545AD,118)
Designhinweise
Route the controller-side SDA and SCL connections directly to the hub, then assign a separate downstream route for each enabled channel. Keep each SDA and SCL pair on consistent PCB layers and minimize stubs and vias. The hub can isolate bus groups electrically, but long branches can still behave like transmission lines; confirm rise time and ringing with the intended peripheral population rather than relying only on the 400 pF group limit.
Determine pull-up placement for the controller-side bus and every downstream branch. The correct resistor value depends on the 3 V to 3.6 V bus voltage, total branch capacitance, pull-up current, and the required rise time at 400 kHz. Do not duplicate strong pull-ups across every branch without checking the aggregate sink current seen by the driver. Verify enable and shutdown sequencing so partially powered peripherals cannot drive an inactive channel during startup.
Do not treat a four-channel switch as a substitute for this five-channel hub. Confirm the 20-pin SOIC footprint, numbered pins, supply pins, ground connections, channel functions, enable polarity, reset behavior, and voltage range before approving any substitute. Similar operating descriptions do not establish pin-to-pin compatibility. For production purchasing, require the exact MPN or manufacturer confirmation that the alternative retains every function required by the target PCB.
Compliance-Informationen
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product page or lot documentation.